Chemistry and melting characteristics of fireside deposits taken from boiler tubes in waste incinerators

Twenty-three tube deposits taken from seven heat-recovery boilers of municipal solid waste incinerators were examined by chemical analyses and X-ray diffraction. These deposits were measured by Differential Scanning Calorimeter (DSC) in N₂ to investigate their melting characteristics. Sixteen deposits were used to evaluate their corrosiveness to carbon steel by high-temperature corrosion test conducted at 400 °C for 20 h in 1500 ppm HCl – 300 ppm SO₂ – 7.5%O₂ – 7.5%CO₂ – 20%H₂O – N₂. Total heat of endothermic reactions of the deposits taking place between 200 and 400 °C can be related to the corrosion rate of carbon steel at 400 °C. Corrosion initiated at temperatures when the deposits started to melt, became severe when fused salt constituents increased, and alleviated when the majority of the deposits became fused. The corrosion can be interpreted as fused salt corrosion caused by chloride and sulfate salts.     

Grain growth and crystallinity of ultrafine barium titanate particles prepared by various routes

Variations in tetragonal distortion and the degree of crystallinity of ultrafine BaTiO₃ particles—both industrially applied criteria qualifying their polar characteristics—upon growth during annealing were studied on powders, prepared by the hydrothermal synthesis and by the oxalate route respectively. Regardless of the synthetic route both these properties were found to develop approximately to the same extent with increasing primary particle size. The degree of crystallinity was detectable only above a critical value of c/a=1.007 at an average particle size of around 120 nm. Intragranular porosity in hydrothermal powders and the stoichiometric Ba/Ti-ratio are of minor influence. However, distinct differences in particle growth behavior for both powders were observed. This discrepancy is ascribed to a special morphology of the hydrothermal product, where enhanced particle growth was found to be governed by oriented attachment of individual crystallites and by the motion of solid–solid interfaces.     

Effects of crystalline form on the tableting compression mechanism of phenobarbital polymorphs

The effects of the polymorphic form on the compression mechanism of forms A, B, and F of phenobarbital were investigated using a compression simulator, mercury porosimetry, X-ray diffraction analysis, BET gas absorption method, and scanning electron microscopic (SEM) photography. The order of tablet hardness obtained from all phenobarbital polymorphs was form A ≥ form B ≥ form F in accordance with that of the specific surface area. The Cooper and Eaton method was applied to evaluate two individual compression processes: particle rearrangement (phase I) and fragmentation and/or deformation (phase II). The parameters for compression processes were calculated using a nonlinear regression analyses program, and the compression energies of phases I and II were calculated from these parameters. The relationship between specific surface area after compression and compression energy at phase I showed a good linear correlation, but their ratio did not. In contrast, the specific surface area ratio showed a linear relationship with the compression energy on phase II, but again the ratio of these two parameters did not. The tablet hardness showed a linear relationship with the specific surface area ratio, but not with the specific surface area. Again, the ratio of these two parameters did not show a linear relationship.     

Effects of water-soluble

The effect of the amount of a water-soluble, lactose, on cephalexin (CEX) release from bioactive bone cement consisting of bisphenol--glycidyl methacrylate (bis-GMA), triethylene-glycol dimethacrylate (TEGDMA) resin and apatite- and wollastonite-containing glass-ceramic (A–W GC) powder was investigated. A–W GC powder containing 5% CEX and lactose powders hardened within 5 min after mixing with bis-GMA/TEGDMA resin, and furthermore its compressive strength was expected to be higher than that of polymethylmethacrylate cement. In vitro CEX release from bioactive bone cement pellets in a simulated body fluid at pH 7.25 and 37°C continued for more than 2 wk. The drug-release rate increased with increasing amount of lactose powder in the mixture. CEX release profiles followed the Higuchi equation in the initial stage, but not in later stages. As hydroxyapatite was precipitated out on the cement surface, the CEX release rate decreased. The micropore distribution of the cements measured by mercury porosimetry also supported the variation in drug release due to cement porosity being mainly a result of the dissolution of lactose in the cements. These results suggest that the rate of CEX release from bioactive bone cement could be controlled by varying the amount of lactose in the cement system. © 1999 Kluwer Academic Publishers     

Stabilization of oscillating modes in a LiNdP4O12laser

Suppression of mode competition in a LiNdP4O12(LNP) laser is reported. The stabilization of the oscillating modes was achieved with a quartz quarter-wave plate placed within an optical resonator without any external modulation.     

Two-dimensional multiarray formation of hepatocyte spheroids on a microfabricated PEG-brush surface

A two-dimensional microarray of ten thousand (100 x 100) hepatocyte heterospheroids, underlaid with endothelial cells, was successfully constructed with 100 microm spacing in an active area of 20 x 20 mm on microfabricated glass substrates that were coated with poly(ethylene glycol) brushes. Cocultivation of hepatocytes with endothelial cells was essential to stabilize hepatocyte viability and liver-specific functions, allowing us to obtain hepatocyte spheroids with a diameter of 100 microm, functioning as a miniaturized liver to secret albumin for at least one month. The most important feature of this study is that these substrates are defined to provide an unprecedented control of substrate properties for modulating cell behavior, employing both surface engineering and synthetic polymer chemistry. The spheroid array constructed here is highly useful as a platform of tissue and cell-based biosensors and detects a wide variety of clinically, pharmacologically, and toxicologically active compounds through a cellular physiological response.     

Analysis of the response of lasers to external signal injection

The rate equation including the injection term was extended and solved numerically. The relation between the peak photon number in the onset of relaxation oscillations of lasers and the injected photon number is shown. The step response of the CW laser to the external signal injection and the reshaping property of the laser for the distorted optical pulse are reported.     

Electromyographic prosthetic hand using grasping-force-magnification mechanism with five independently driven fingers

This paper proposes an electromyographic (EMG) prosthetic hand that has five independently driven fingers, a flexion drive, and a force-magnification drive. The flexion drive allows for rapid finger motion, and the force-magnification drive allows for a firm grasp. To realize the natural feeling of control similar to that of movements with nonamputated parts, the control system includes the impedance model of human forearms and utilizes the muscle contraction level extracted from a user’s EMG signals. We experimentally verified that the maximum fingertip force of the hand exceeds 20 N, and the time required to fully close the hand by the flexion drive is 0.53 s. We also experimentally verified that in response to EMG signals, the fingers can flex smoothly and the grasping force can be modulated. Furthermore, we show that taking EMG signals as inputs makes it possible to control six operations, including ones that use the five fingers in distinctive ways.     

Analyses of mode-hopping phenomena in an AlGaAs laser

Intensity fluctuations of the longitudinal modes of a 0.8 μm AlGaAs laser were precisely measured during the occurrence of hopping between two modes. It was found from this result that mode hopping follows the stochastics of a Poisson process. The frequency of mode hopping was measured asf_{c} = [exp [-95(I/I_{th} - 1)]] times 10^{7}(Hz). whereI/I_{th}is the injection current normalized to its threshold value. Results of analog computer simulations showed that spontaneous emission worked as a triggering force for mode hopping. Results of the analysis based on the Fokker-Planck equation were compared to the experimental results, from which the root-mean-square value of the fluctuating electric field of spontaneous emission was estimated as2.3 times 10^{2)(V/m)leqlanglesim{E}_{N} leq 3.2 times 10^{2}(V/m). It is concluded that an effective reduction of mode hopping is achieved if the laser is operated at a higher bias or if the coupling constant between the two modes is increased.     

Robust disturbance-rejection problems for linear ω-periodicdiscrete-time systems

Two robust disturbance-rejection problems with state feedback and with incomplete-state feedback for linear ω-periodic discrete-time systems are studied in the framework of the so-called geometric approach. Also, some necessary conditions and/or sufficient conditions for the problems to be solvable are presented