Wide frequency range sine wave VCO with a tunable inductor andcapacitor

A voltage-controlled oscillator (VCO) with sine wave output has been built using a tunable inductor along with a tunable capacitor to operate at frequencies ranging from 100 kHz to over 20 MHz. The method of tuning the inductor by changing the permeability of its ferrite core and the ability to extend the frequency response of the core are discussed. Dynamic characteristics of the VCO are explained with examples of a parallel and series tank implementation     

Effects of manufacturing defects on the mechanical properties of carbon fibre reinforced polyethersulphone laminates

The effects of defects on the mechanical properties of carbon fibre reinforced polyethersulphone laminates have been measured. The defects studied were cut fibre plies, omission of polymer films and local delamination produced by the inclusion of foreign matter. Of these it was found that only cut plies had a significant detrimental effect on the strength of a laminate. For specimens with two cut plies, the failure stress, tensile, flexural and compressive in the remaining continuous plies was the same as in the defect-free material, provided that the cut plies were widely separated. However the failure stresses were 15–18% lower in the continuous plies in the specimens containing two cut plies which were more closely spaced and in specimens containing four cut plies.     

Study of dielectric properties of RbNO3 single crystals

Dielectric properties, dielectric constant (k), dielectric loss (tan δ) and a.c. conductivity (σ) in the solution-grown single crystals of RbNO₃ are presented from room temperature to about 200°C covering the frequency range 10² to 10⁵ Hz. A broad peak observed in tan δ-frequency data between 10³ and 10⁵Hz is thought to be due to impurity-vacancy dipoles. The sudden rise of three parameters near 160°C is attributed to the known phase transition from trigonal to CsCl structure.     

Influence of ash deposits on the heat resistance of materials for gas turbine engine blades

Leningrad. Translated from Problemy Prochnosti, No. 1, pp. 71–76, January, 1989.     

Thermomechanical behaviour of composites

This paper derives the governing equations for the thermomechanical behaviour of composites. When the basic equations for the thermoelastic behaviour of solids were first derived in the nineteenth century several approximations were made. The effect of these assumptions are discussed and illustrated by the results of a simple laboratory test. The implications of this work on the analysis of impact damaged laminates are then discussed.     

Stress distribution in orthotropic plates with coupled elastic properties

Summary If the roots of the characteristic equation of the governing differential equation for the stress function of an orthotropic plate under generalized plane stress conditions are equal classical solutions of anisotropic elasticity theory do not hold anymore. The general form of the stress function for such orthotropic materials is discussed and the exact solution is given for the plate with an elliptic opening loaded in tension.Comparison of the stress distribution for the material with distinct characteristic roots indicated that in produces much higher stress concentrations than the model with equal roots. For the latter case solution of any boundary value problem may be obtained very easily through an existing solution for the isotropic material.Given also that there are several problems involving stress concentrations in orthotropic plates as yet unsolved, the analysis presented here might be of considerable help in the, designing of the structure of composite laminates.With 8 Figures     

Toughening of Dental Porcelain by Tetragonal ZrO2 Additions

The effect on mechanical behavior of ZrO₂ additions to a dental porcelain was investigated. The ZrO₂ was introduced into the glassy matrix phase of the porcelain by refritting the all-glass porcelain constituent. X-ray diffraction indicated that a sizeable fraction of the ZrO₂ was retained in the tetragonal form after the porcelain was fired. Zirconia additions to the porcelain produced substantial improvements in fracture toughness, strength, and thermal shock resistance.     

Long-term working memory in the rat: Effects of hippocampally applied anisomycin.

The extent to which protein synthesis is involved in working memory was investigated with the protein synthesis inhibitor anisomycin (ANI). Male albino and Long-Evans rats were trained to perform accurately on a 12-arm radial maze when delays of 240 min were interposed between Choice 6 and Choice 7. Bilateral hippocampal cannulas were then implanted. Accuracy on Choices 7–22 was studied when ANI (80 μg/μl) or saline was injected either 30 min before Choice 1 or 5–20 min after Choice 6 in Exp I. Pretrial injection of ANI significantly impaired performance following the 240-min delay, whereas ANI injected during the delay had no such effect. In Exps II and III, the ANI-induced amnesia was replicated, and the temporal course of development of the amnesia was determined. Pretrial administration of ANI did not significantly affect retention after a 2-min delay but produced amnesia after delays of 15 min or longer. Data suggest that protein synthesis is important for the formation of temporary memories, provided the retention interval is long enough. It is suggested that working memory includes both short- and long-term components. Protein synthesis appears to be important for formation of the long-term component, but not the short-term component, of working memory. (31 ref) (PsycINFO Database Record (c) 2010 APA, all rights reserved)