An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

Organic matter release in low temperature thermal treatment of biological sludge for reduction of excess sludge production.

Thermal treatment applied in association with a biological system allows for a significant reduction in excess sludge production (approximately 50%). In general, heat treatment is described as a sludge disintegration technique. This paper offers a thorough study on the impact of heat treatment, at temperatures below 100 degrees C, on the solubilisation of the sludge COD and its biodegradability. Discontinuous heating experiments were performed on activated and digested sludge. At all temperatures tested the released COD for digested sludge was systematically higher than that for activated sludge (15 and 40%, respectively, at 95 degrees C for 40 min of contact time). For the first 30 min, a 1st order kinetic, with respect to the residual COD, was systematically found. In the range of 40-95 degrees C, digested sludge had a lower activation energy than activated sludge (26 kcal/mol compared to 70-160 kcal/mol). COD solubilisation is thus more positively influenced by temperature in the case of activated sludge. This may be due to the significant difference in the ratio of protein/carbohydrate in digested and activated sludge (1-5 and 0.2-0.7, respectively). The increase in the COD/TKN ratio in the solubilised fraction after thermal treatment of activated sludge suggests a preferential solubilisation of proteins over carbohydrates. Respirometric tests performed on the solubilised COD showed that whatever the sludge origin, only 40-50% of released COD is biodegradable at a conventional hydraulic retention time (i.e., 24 h). Hence, heat treatment would act more through organic matter solubilisation rather than by a biodegradability increase.     

Evaluating software reuse alternatives: a model and its application to an industrial case study

We propose a model that enables software developers to systematically evaluate and compare all possible alternative reuse scenarios. The model supports the clear identification of the basic operations involved and associates a cost component with each basic operation in a focused and precise way. The model is a practical tool that assists developers to weigh and evaluate different reuse scenarios, based on accumulated organizational data, and then to decide which option to select in a given situation. The model is currently being used at six different companies for cost-benefit analysis of alternative reuse scenarios; we give a case study that illustrates how it has been used in practice.     

Thermal Transformations of an Aluminoborophosphate Binder

Thermal transformations of a commercial aluminoborophosphate binder are studied in a broad temperature range by optical microscopy, x-ray diffraction, IR spectroscopy, and thermal analysis. The introduction of B₂O₃ reduces the temperature of phosphate polycondensation, enhances the stability of cyclometaphosphates in a broad temperature range (180–1100°C), and reduces the stability of hydrogen phosphates.     

A test for the statistical significance of DNA sequence similarities for application in databank searches

A method is developed, based on word-searching, which provides a rapid test for the statistical significance of DNA sequence similarities for use in databank searching. The method makes allowance for the lengths and dinucleotide compositions of the sequences being compared. A way is also described to calculate the power of the test, i.e. the probability of detecting a given similarity as being statistically significant. The effects on the power of the test of the scoring method, word length, sequence length, and sequence composition are examined. A novel scoring method is shown to be superior to the method currently used in most word-searching algorithms.     

Use of electrochemical oxidation process as post-treatment for the effluents of a UASB reactor treating cellulose pulp mill wastewater.

The main purpose of this study was to evaluate the performance of the electrochemical oxidation process as a post-treatment for the effluents of a bench-scale UASB reactor treating simulated wastewater from an unbleached pulp plant. The oxidation process was performed using a single compartment cell with two plates as electrodes. The anode was made of Ti/Ru0.3Ti0.7O2 and the cathode of stainless steel. The following variables were evaluated: current density (75, 150 and 225 mA cm(-2)) and recirculation flow rate in the electrochemical cell (0.22, 0.45 and 0.90 L h(-1)). The increase in current density from 75 to 225 mA cm(-2) did not increased the color removal efficiency for the tested flow rates, 0.22, 0.45 and 0.90 L h(-1), however the energy consumption increased significantly. The results indicated the technical feasibility of the electrochemical treatment as post-treatment for UASB reactors treating wastewaters from pulp and paper plants.     

Markov analysis of qualitative dynamics1

Common sense sometimes predicts events to be likely or unlikely rather than merely possible. We extend methods of qualitative reasoning to predict the relative likelihoods of possible qualitative behaviors by viewing the dynamics of a system as a Markov chain over its transition graph. This involves adding qualitative or quantitative estimates of transition probabilities to each of the transitions and applying the standard theory of Markov chains to distinguish persistent states from transient states and to calculate recurrence times, settling times, and probabilities for ending up in each state. Much of the analysis depends solely on qualitative estimates of transition probabilities, which follow directly from theoretical considerations and which lead to qualitative predictions about entire classes of systems. Quantitative estimates for specific systems are derived empirically and lead to qualitative and quantitative conclusions, most of which are insensitive to small perturbations in the estimated transition probabilities. The algorithms are straightforward and efficient.     

An intrinsic observer for a class of Lagrangian systems

We propose a new design method of asymptotic observers for a class of nonlinear mechanical systems: Lagrangian systems with configuration (position) measurements. Our main contribution is to introduce a state (position and velocity) observer that is invariant under any changes of the configuration coordinates. The observer dynamics equations, as the Euler-Lagrange equations, are intrinsic. The design method uses the Riemannian structure defined by the kinetic energy on the configuration manifold. The local convergence is proved by showing that the Jacobian of the observer dynamics is negative definite (contraction) for a particular metric defined on the state-space, a metric derived from the kinetic energy and the observer gains. From a practical point of view, such intrinsic observers can be approximated, when the estimated configuration is close to the true one, by an explicit set of differential equations involving the Riemannian curvature tensor. These equations can be automatically generated via symbolic differentiations of the metric and potential up to order two. Numerical simulations for the ball and beam system, an example where the scalar curvature is always negative, show the effectiveness of such approximation when the measured positions are noisy or include high frequency neglected dynamics.