Irradiation effects of boron carbide used as control rod elements in fast breeder reactors

The paper describes radiation effects on 8₄C pellets used as control rod elements in the Enrico Fermi Fast Breeder Reactor. Pellet swelling (Δ$\text{V/V}$) caused by irradiation was less than 1% in which crystal lattice swelling was less than 20%. Many microcracks, a main cause of pellet swelling, appeared in the irradiated pellets. The production of microcracks was related to graphite precipitation in the pellets before irradiation. Open pores which did not exist in the unirradiated pellets were formed in the irradiated ones. In a unit cell of B₄C, the α-axis elongated by 0.025 Å and the $\text{c-}\text{axis}$ shrank by 0.07 Å by irradiation. Moreover, we found three recovery stages which were from room temperature to 400°C, from 400 to 750°C and from 850 to 1100°C. The recovery mechanisms in the irradiated pellets are discussed in terms of the helium behavior.     

Loss of H19 imprinting and up-regulation of H19 and SNRPN in a case with malignant mixed Müllerian tumor of the uterus

An unusual clinical presentation of a patient with neuronal intestinal dysplasia is presented. A 46-year-old male noted a palpable mass in the right lower quadrant of his abdomen for two months. A computed axial tomographic scan showed a thickened wall of the cecum with a tumor-like appearance. The excised specimen consisted of a mass caused by the thickened, edematous wall of the dilated cecum and appendix. The wall of the cecum and appendix measured up to 2.5 and 0.8 cm, respectively, in thickness. Microscopic studies showed extensive hyperplasia and hypertrophy of the ganglia and nerve plexuses and hypertrophy of the muscularis propria, consistent with neuronal intestinal dysplasia.     

Relationship between local structure and stability in hen egg white lysozyme mutant with alanine substituted for glycine

We prepared five mutant lysozymes in which glycines whose dihedralangles are located in the region of the left-handed helix, Gly49,Gly67, Gly71, Gly102 and Gly117, were mutated to an alanineresidue. From analyses of their thermal stabilities using differentialscanning calorimetry, most of them were more destabilized thanthe native lysozyme, except for the G102A mutant, which hasa stability similar to that of the native lysozyme at pH 2.7.As for the destabilized mutant lysozymes, their X-ray crystallographicanalyses showed that their global structures did not changebut that the local structures changed slightly. By examiningthe dihedral angles at the mutation sites based on X-ray crystallographicresults, it was found that the dihedral angles at these mutationsites tended to adopt favorable values in a Ramachandran plotand that the extent and direction of their shifts from the originalvalue had similar tendencies. Therefore, the change in dihedralangles may be the cause of the slight local structural changesaround the mutation site. On the other hand, regarding the mutationof G102A, the global structure was almost identical with thatof the native structure but the local structure was drasticallychanged. Therefore, it was suggested that the drastic localconformational change might be effective in releasing the unfavorableinteraction of the native state at the mutation site.     

Concentration of docosahexaenoic acid in glyceride by hydrolysis of fish oil withcandida cylindracea lipase

In an attempt to concentrate the content of DHA (docosahexaenoic acid) in a glyceride mixture containing triglyceride, diglyceride and monoglyceride, fish oil was hydrolyzed with six kinds of microbial lipase. After the hydrolysis, free fatty acid was removed and fatty acid components of the glyceride mixtures were analyzed. When the hydrolysis withCandida cylindracea lipase was 70% complete, the DHA content in the glyceride mixture was three times more than that in the original fish oil. The EPA (eicosapentaenoic acid) content became almost 70% of the original fish oil. Hydrolysis with other lipases did not result in an increase in the DHA content in the glyceride mixtures. Hydrolysis of DHA-rich tuna oil (DHA content is about 25%) withCandida cylindracea lipase resulted in 53% DHA in the glyceride mixture. The EPA content, however, remained close to that of the original tuna oil. In this report, the acyl chain specificity of lipases is evaluated in terms of hydrolysis resistant value (HRV). HRV is the ratio between the DHA contents in the glyceride mixture of hydrolyzed oil and original oil. HRV clearly indicates differences in hydrolysis between DHA and other fatty acids (e.g., saturated and monoenoic acids).     

Ru-catalyzed anode materials for direct hydrocarbon SOFCs

A solid oxide fuel cell using a thin ceria-based electrolyte film with a Ru-catalyzed anode was directly operated on hydrocarbons, including methane, ethane, and propane, at 600 °C. The role of the Ru catalyst in the anode reaction was to promote the reforming reaction of the unreacted hydrocarbons by the produced steam and CO₂, which avoided interference from steam and CO₂ in the gas-phase diffusion of the fuels. The resulting peak power density reached 750 mW cm⁻² with dry methane, which was comparable to the peak power density of 769 mW cm⁻² with wet (2.9 vol.% H₂O) hydrogen. More important was the fact that the cell performance was maintained at a high level regardless of the change in the methane utilization from 12 to 46% but was significantly reduced by increasing the hydrogen utilization from 13 to 42%. While the anodic reaction of hydrogen was controlled by the slow gas diffusion, the anodic reaction of methane was not subject to the onset of such a gas-diffusion process.     

Synthesis of single-phase Ti3SiC2 powder

In this study, free 2Ti/2Si/3TiC powder mixture was heated at high temperatures in vacuum, in order to reveal the possibility for the synthesis of high Ti₃SiC₂ content powder. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used for the evaluation of phase identities and the morphology of the powder after different treatments. Results showed that almost single phase Ti₃SiC₂ powder (99.3 wt.%) can be synthesized by heat treatment with free 2Ti/2Si/3TiC powders in vacuum at 1210°C for about 3 h. The nucleation and growth of Ti₃SiC₂ within TiC particles was observed. The typical appearance of the formed Ti₃SiC₂ is equiaxed with particle size of 2–4 μm. Effects of temperature and heating time on the morphology and the particle sizes of the synthesized Ti₃SiC₂ powders are not obvious.     

Effects of support and additive on oxidation state and activity of Pt catalyst in propane combustion

The effects of support and additive on the oxidation state and catalytic activity of Pt catalyst in the low temperature propane combustion were systematically investigated on Pt/MgO, Pt/Al₂O₃ and Pt/SiO₂–Al₂O₃. The catalytic activity varied much with both support materials and additives. The catalyst on the more acidic support showed higher activity, and the catalytic activity on every support materials increased as the electronegativity of additives increased, while some additives decreased the activity. The oxidation state of platinum, estimated by white line intensity of Pt L_III-edge XANES spectrum, also varied with the support and additives, and additives with higher electronegativity greatly prevented the platinum from its oxidation under oxidising atmosphere. Among almost all the catalysts with various supports and various additives, a clear relationship was observed between the oxidation state of platinum and the catalytic activity; the more metallic platinum showed higher activity. Thus, it was concluded that the total electrophilic/electrophobic property derived from those of the support and additive controls the oxidation state of platinum, which intensively affects the catalytic activity; i.e. higher electrophilic property provides less oxidised platinum, resulting in high catalytic activity. The mechanism of this effect was also discussed on the basis of thermochemical data, and it was proposed that the electrophobic materials promote the noble metal oxidation since the noble metal oxo-anion such as PtO^δ− is more stabilised with electrophobic cation.     

Oxidation kinetics for <Emphasis Type="Italic">cis</Emphasis>-9,<Emphasis Type="Italic">trans</Emphasis>-11 and <Emphasis Type="Italic">trans</Emphasis>-10,<Emphasis Type="Italic">cis</Emphasis>-12 isomers of CLA

The autoxidation processes of the cis-9,trans-11 (c9,t11) and trans-10,cis-12 (t10,c12) isomers of CLA were separately observed at ca. 0% RH and different temperatures. The t10,c12 CLA oxidized faster than the c9,t11 isomer at all tested temperatures. The first half of the oxidation process of t10,c12 CLA obeyed an autocatalytic-type rate expression, but the latter half followed first-order kinetics. On the other hand, the entire oxidation process of c9,t11 CLA could be expressed by the autocatalytic-type rate expression. The apparent activation energies and frequency factors for the autoxidation of the isomers were estimated from the rate constants obtained at various temperatures based on the Arrhenius equation. The apparent activation energies for the CLA isomers were greater than those for the nonconjugated n−6 and n−3 PUFA or their esters. However, the enthalpyentropy compensation held during the autoxidation of both the CLA and PUFA. This suggested that the autoxidation mechanisms for the CLA and PUFA were essentially the same.     

Fabrication and Microstructure Characterization of Ti3SiC2 Synthesized from Ti/Si/2TiC Powders Using the Pulse Discharge Sintering (PDS) Technique

Ti/Si/2TiC powders were prepared using a mixture method (M) and a mechanical alloying (MA) method to fabricate Ti₃SiC₂ at 1200°–1400°C using a pulse discharge sintering (PDS) technique. The results showed that the Ti₃SiC₂ samples with <5 wt% TiC could be rapidly synthesized from the M powders; however, the TiC content was always >18 wt% in the MA samples. Further sintering of the M powder showed that the purity of Ti₃SiC₂ could be improved to >97 wt% at 1250°–1300°C, which is ∼200°–300°C lower than that of sintered Ti/Si/C and Ti/SiC/C powders using the hot isostatic pressing (HIPing) technique. The microstructure of Ti₃SiC₂ also could be controlled using three types of powders, i.e., fine, coarse, or duplex-grained, within the sintering temperature range. In comparison with Ti/Si/C and Ti/SiC/C mixture powders, it has been suggested that high-purity Ti₃SiC₂ could be rapidly synthesized by sintering the Ti/Si/TiC powder mixture at relatively lower temperature using the PDS technique.