Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

Fast DCT algorithm with fewer multiplication stages

A novel fast DCT scheme with reduced multiplication stages and fewer additions and multiplications is proposed. The proposed algorithm is structured so that most multiplications tend to be performed at the final stage, which reduces the propagation error that could occur in the fixed-point computation. Minimisation of the multiplication stages can further decrease the error     

Enhanced direct stiffness method for finite element analysis of textile composites

Traditional homogenization techniques are not useful when the microstructural scale of a material is of the same order of magnitude as the structural scale of a component. Such is the case for many textile composites. Since discrete modeling of the microstructure throughout a component is prohibitively expensive, continuum finite elements are needed which account for the microstructure within a single element. This paper describes a simple substructuring technique for formulating these special elements.     

Serum amyloid P component scintigraphy and turnover studies for diagnosis and quantitative monitoring of AA amyloidosis in juvenile rheumatoid arthritis

OBJECTIVE: To evaluate aspects of the natural history of AA amyloidosis complicating juvenile rheumatoid arthritis (JRA), and its response to therapy with chlorambucil. METHODS: Scintigraphy and 7-day turnover studies were performed in JRA patients with histologically proven (n = 35) or clinically suspected (n = 30) AA amyloidosis, following intravenous injection of 123I and 125I-labeled serum amyloid P component (SAP). Prospective monitoring studies were performed over 2-3 years in 20 patients with amyloidosis. All but 2 amyloidosis patients were treated with chlorambucil. RESULTS: Positive scanning results were obtained in all patients in whom imaging was performed within 12 years of positive biopsy findings of amyloid and in 5 patients with clinically suspected amyloidosis. Negative scanning results with normal SAP metabolism, indicating regression of amyloid, were obtained in 4 patients whose amyloidosis had been in full clinical remission for more than 12 years. Prospective monitoring studies in patients whose JRA-associated inflammatory activity was in remission demonstrated regression of amyloid in 8 patients and no substantial changes in 8 others; however, in 4 further patients with active inflammation, there was accumulation of amyloid. There was a very poor correlation between the amount of amyloid present at a particular site and the resultant organ dysfunction. CONCLUSION: Radiolabeled SAP scintigraphy and turnover studies are useful complementary tools in the diagnosis, screening, and quantitative monitoring of type AA amyloidosis in JRA. The amyloid deposits may progress and/or regress at different rates in different anatomic sites over short periods.     

Heat transfer enhancement by Marangoni convection in the NH3–H2O absorption process

The objectives of this paper are to quantify the effect of Marangini convection on the absorption performance for the ammonia–water absorption process, and to visualize Marangoni convection that is induced by adding a heat transfer additive, n-octanol. A real-time single-wavelength holographic interferometer is used for the visualization using a He–Ne gas laser. The interface temperature is always the highest due to the absorption heat release near the interface. It was found that the thermal boundary layer (TBL) increased faster than the diffusion boundary layer (DBL), and the DBL thickness increased by adding the heat transfer additive. At 5 s after absorption started, the DBL thickness for 5 mass% NH₃ without and with the heat transfer additive was 3.0 and 4.5 mm, respectively. Marangoni convection was observed near the interface only in the cases with heat transfer additive. The Marangoni convection was very strong just after the absorption started and it weakened as time elapsed. It was concluded that the absorption performance could be improved by increasing the absorption driving potential (x_vb−x_vi) and by increasing the heat transfer additive concentration. The absorption heat transfer was enhanced as high as 3.0–4.6 times by adding the heat transfer additive that generated Marangoni convection.     

High Gd Concentration GaGdN Grown at Low Temperatures

GaGdN layers were grown at temperatures below 300°C by radio-frequency plasma-assisted molecular beam epitaxy on sapphire substrates. GaGdN samples with high Gd concentration as high as 12.5% were obtained by lowering the growth temperature. X-ray diffraction results showed no obvious secondary phase, which means that the phase separation can be suppressed by the growth at low temperatures. All samples, including those grown at room temperature, showed ferromagnetic characteristics. Photoluminescence emission was observed, though spectra exhibit broad and sharp luminescence bands related to many kinds of defects. It is suggested that electrons coming from defects, especially, nitrogen vacancy, stabilize ferromagnetism, and that the carrier-induced ferromagnetism occurs in the low-temperature-growth GaGdN.     

Decreasing miscibility with greater heterogeneity in ternary polymer blend: poly(cyclohexyl methacrylate), poly(α‐methyl styrene) and poly(4‐methyl styrene)

A ternary blend system comprising poly(cyclohexyl methacrylate) (PCHMA), poly(α‐methyl styrene) (PαMS) and poly(4‐methyl styrene) (P4MS) was investigated by thermal analysis, optical and scanning electron microscopy. Ternary phase behaviour was compared with the behaviour for the three constituent binary pairs. This study showed that the ternary blends of PCHMA/PαMS/P4MS in most compositions were miscible, with an apparent glass transition temperature (T_g) and distinct cloud‐point transitions, which were located at lower temperatures than their binary counterparts. However, in a closed‐loop range of compositions roughly near the centre of the triangular phase diagram, some ternary blends displayed phase separation with heterogeneity domains of about 1 µm. Therefore, it is properly concluded that ternary PCHMA/PαMS/P4M is partially miscible with a small closed‐loop immisciblity range, even though all the constituent binary pairs are fully miscible. Thermodynamic backgrounds leading to decreased miscibility and greater heterogeneity in a ternary polymer system in comparison with the binary counterparts are discussed. © 2003 Society of Chemical Industry     

On teletraffic applications to OBS

We provide teletraffic models for loss probability evaluation of optical burst switching (OBS). We show that the popular Engset formula is not exact for OBS modeling and demonstrate that in certain cases it is not appropriate. A new exact model is provided. The various models are compared using numerical results for various OBS alternatives with and without burst segmentation.     

The oxidative inducation test applied to medical PVC and other polymers

We have examined the applicability of this simple and effective test to polymer systems widely used in the medical industry. First, it was found that not every polymer examined exhibited a distinct onset of autocatalytic oxidation detectable by DSC. However, for cases where distinct onsets are found, powerful insights can be obtained. These included activation energy of the degradation, thermal oxidative shelf life prediction, and correlation, with product performances. Actual examples are presented to illustrate the utility of the test.     

Electrical characterization of porous BaTiO3 using impedance spectroscopy in humid condition

The humidity response characteristics of La doped BaTiO₃ with different sintered densities and room temperature electrical conductivities were investigated using complex impedance measurement. The samples with low density and high resistivity showed the large and nearly linear sensitivity to the change of humidity. The impedance spectra of samples, when exposed to high humidity, can exhibit microstructure-related features, even though they do not give rise to a noticeable characteristic change when exposed to low humidity. The observed impedance patterns were dependent upon the density, and hence the oxidation kinetics of BaTiO₃.