Deposition of DLC film with adhesive W-DLC layer on stainless steel and its tribological properties

Tribological properties of a diamond-like carbon (DLC) coating with an adhesive tungsten-containing DLC (W-DLC) layer were investigated. The coatings were deposited onto AISI316L steel substrates and Si wafers using plasma enhanced chemical vapor deposition and tungsten co-sputtering of the metal target. Methane and argon gases were used as the precursor of the coatings. In this study, three types of coatings were evaluated: DLC/W-DLC on AISI316L (DLC-1), DLC/W-DLC on Si wafer (DLC-2), and DLC on Si wafer (DLC-3). The structural characterizations were performed by transmission electron microscopy and tapping mode atomic force microscopy. At the boundary between the W-DLC layer and the AISI316L substrate, microscopic decohesion or delamination was not observed. The surface roughness of the DLC-1 coating was greater than that of the DLC-2 coating. This feature was derived from the surface roughness of the initial surface of the AISI316L substrate. Friction tests were performed using a rotation-type ball-on-flat configuration tribometer. The observed friction of the DLC-1 coating was unstable compared with the DLC-2 or DLC-3 coatings. This was due to wear debris which had risen to the friction surface resulting in unstable friction on the DLC-1 coating. During the friction studies, the top DLC layer was removed from the adhesive W-DLC layer because the adhesive strength at this part was not enough. In order to achieve the low and stable friction of the DLC coating with the W-DLC layer on AISI316L, it is necessary to improve the smoothness of the surface and the adhesion between the DLC coating and the W-DLC layer.     

Study of drive system for linear induction motor using magnetic energy recovery switch

This paper proposes a power supply suitable for driving linear induction motors. The power supply consists of a voltage source inverter (VSI) and a magnetic energy recovery switch (MERS). Circuit configuration and operation principles of the power supply are described. Power factor correction by MERS can increase the output power. Technical advantages of using MERS compared with increasing the rated voltage of VSI are discussed. Some experiments with a linear induction motor were conducted. The results confirm that MERS can reduce the capacity of the VSI or increase the output with the same VSI capacity. The number of devices and magnitude of losses are evaluated on a large‐scale drive system. A half‐bridge type of MERS is provided and discussed. The half‐bridge MERS mitigates disadvantages of using MERS. © 2009 Wiley Periodicals, Inc. Electr Eng Jpn, 169(4): 65–74, 2009; Published online in Wiley InterScience ( www.interscience. wiley.com ). DOI 10.1002/eej.20832     

Effect of Pore–Grain-Boundary Interactions on Discontinuous Grain Growth

Pore behavior as influenced by migration of an abnormal grain boundary was studied. The pore behavior during the discontinuous growth of hot-pressed spinel (MgAl₂O₄) — whether the pore can move attached to the grain boundary — is particularly governed by the pore size and the matrix grain size. These phenomena can be understood from the interaction between the pore and the abnormal grain boundary.     

Temperature Dependence of the Raman Spectrum in Lithium Oxide Single Crystal

Temperature dependence of the Raman spectrum of lithium oxide single crystal has been measured over a temperature range of 80 to 1073 K. The frequency shift and the line width of the Raman spectrum in lithium oxide were about 531 and 4.5 cm^-1 at 80 K, respectively. At 1073 K, the frequency shift and the line width attained the values of 464 and 112 cm^-1, respectively. The strong temperature dependence of the frequency shift and line width was compared with data from some crystals with a fluorite structure.     

EFFECT OF BAFFLE ON TRAY UNDER OSCILLATING CONDITION

Effect of baffle on a tray under oscillating conditions has been examined experimentally. To reduce the degree of liquid mixing and liquid channeling under oscillating conditions, it is necessary to install the baffles on tray.

Experiments were conducted with the air-water system, ft was found that the pressure drop change can be expressed as a sinusoidal function and the period coincides with tray oscillation. The degree of liquid mixing decreases when the baffles are installed on tray and it also decreases with the increase of liquid flow rate. The pressure drop increases with the installation of baffle on tray.

The suitable baffle number on tray is from 4 to 8 and in this region, the degree of liquid mixing reaches minimum and the liquid holdup takes a maximum value. @KEYWORDS: Tray, Oscillating, Liquid mixing, Baffle, Pressure drop, Liquid holdup.     

Binding of organic anions by synthetic supramolecular metallopores with internal Mg2+-aspartate complexes

We report that cation-selective transmembrane pores formed by synthetic p-octiphenyl beta barrels with internal aspartate residues can be transformed into anion-permeable metallopores with internal Mg(2+)-aspartate complexes. These metallopores are shown to be useful for fluorimetric sensing of a broad variety of organic anions of biological relevance such as phytate, heparin, thiamine phosphates, and adenosine triphosphate. The negligible flippase activity measurable for Mg(2+)-free pores indicates that transmembrane p-octiphenyl beta barrels do not disturb the lipid bilayer suprastructure, in other words, they form barrel-stave rather than toroidal pores.     

Dielectric properties of Permalloy granular composite materials

Dielectric and electrical properties of Permalloy granular composite materials have been studied considering the application to left-handed meta-materials. Surface oxidized Permalloy particles have high surface electrical resistance; the eddy current effect in the composite structure is suppressed. The electrical conductivity of compacted Permalloy particles increases with increasing temperature and indicates the semiconductive layer formation on the particle. The low frequency ac electrical conductivity of Permalloy composite materials shows a drastic increase in the particle content between 50 and 60 vol.%. Electrical permittivity spectra of Permalloy composites show a non-metallic characteristic and the enhancement of permittivity is observed with increase of Permalloy particle content.     

New dissimilarity measure for recognizing noisy subsequence trees

Tree is a data structure used to express various objects such as semistructured data and genes. When objects are represented as trees, computing tree similarity is essential for pattern recognition and retrieval. This paper considers the noisy subsequence tree recognition problem whose purpose is to recognize the original tree, given its noisy subsequence tree. Previous research on this problem relied on constrained tree edit distance to measure the dissimilarity. However, the number of relabelings must be predetermined to compute it. This paper proposes a new dissimilarity measure for this problem. Our dissimilarity measure is obtained by counting the node edit operations included in the unit‐cost tree edit distance that contribute to the matching of node labels. The number of relabelings need not be specified to compute our dissimilarity measure. Moreover, our measure achieves more accurate recognition performance and faster execution speed than the constrained tree edit distance. Our measure is also useful to solve the tree inclusion problem which is the problem of deciding whether a tree includes another tree and shows the extent of approximate tree inclusion when a tree incompletely includes another tree. © 2011 Wiley Periodicals, Inc.     

Logichart — Intelligible Program Diagram for Prolog and its Processing System

An intelligible program diagram called Logichart has been developed for Prolog visualization. Its syntax rules and layout rules are formalized in terms of an attribute graph grammar. This grammar is underlain by a context–free graph grammar whose productions are defined to formalize the graph–syntax rules of Logichart diagrams. Semantic rules attached to the productions are defined in such a way that they can extract the layout information needed to display a Logichart diagram as attributes. Our Prolog visualization system, which has been implemented based on the attribute graph grammar, can draw a Logichart diagram for any correct Prolog program (completeness), and any Logichart diagram displayed by the system is always valid for the grammar (soundness). The system can also display the execution of a Prolog program in real time; that is, the Logichart diagram is dynamically updated as the program runs.