Generation of adaptive gait patterns for quadruped robot with CPG network including motor dynamic model

This paper describes the generation of adaptive gait patterns using new Central Pattern Generators (CPGs) including motor dynamic models for a quadruped robot under various environments. The CPGs act as the flexible oscillators of the joints and adjust joint angles to required values. The CPGs are interconnected with each other and sets of their coupling parameters are adjusted by a genetic algorithm so that the quadruped robot can realize stable and adequate gait patterns. Generation of gait patterns results in the formation of the CPG networks suitable for the formation of not only a straight walking pattern but also of rotating gait patterns. Experimental results demonstrate that the proposed CPG networks are effective for the automatic adjustment of the adaptive gait patterns for the tested quadruped robot under various environments. Furthermore, the target tracking control based on image processing is achieved by combining the general gait patterns. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(1): 35–43, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20225     

Tissue compatibility of polylactic acids in the skeletal site

This study was undertaken to examine the osseous tissue compatibility of polylactic acid (PLA) with properties of bioabsorbability and plasticity. Two kinds of granular PLA with different molecular weight (PLA-H: 28 000 MW, PLA-L: 10 600 MW) were implanted into rat tibiae and light microscopic sections were prepared at 1, 2, 4, 8, 16, and 24 weeks following surgery. The tissue compatibility of the PLAs was compared with that of hydroxyapatite (HAP) which is a non-absorbable biocompatible material. After implantation, both PLAs were gradually absorbed and replaced by marrow tissue at 24 weeks. PLA-H degraded slower than PLA-L. New bone formation was observed around each PLA by 4 weeks, and a vast amount of bone deposited on PLA-H at 16 weeks. Phagocytic reactions to the PLAs were noted, however, severe inflammation was not seen. HAP was not absorbed and bone surrounded it throughout the experiment. These results indicate good tissue compatibility of PLA as a bioabsorbable material at the skeletal site.     

Fine physical mapping of Ph1, a chromosome pairing regulator gene in polyploid wheat

The diploid-like chromosome pairing in polyploid wheat is controlled by the Ph1 (pairing homoeologous) gene that is located on chromosome arm 5BL. By using a combination of cytogenetic and molecular techniques, we report the physical location of the Ph1 gene to a submicroscopic chromosome region (Ph1 gene region) that is flanked by the breakpoints of two deletions (5BL-1 and ph1c) and is marked by a DNA probe (XksuS1). The Ph1 gene region is present distal to the breakpoint of deletion 5BL-1 but proximal to the C-band 5BL2.1. Two other DNA probes (Xpsr128 and Xksu75) flank the region-Xpsr128 being proximal and Xksu75 being distal. The estimated size of the region is less than 3 Mb. The chromosome region around the Ph1 gene is high in recombination as the genetic distance of the region between 5BL-1 breakpoint and C-band 5BL2.1 (not resolved by the microscope) is at least 9.3 cM.     

Systematic analysis of neutron yields from thick targets bombarded by heavy ions and protons with moving source model

A simple phenomenological analysis using the moving source model has been performed on the neutron energy spectra produced by bombarding thick targets with high energy heavy ions which have been systematically measured at the Heavy-Ion Medical Accelerator (HIMAC) facility (located in Chiba, Japan) of the National Institute of Radiological Sciences (NIRS). For the bombardment of both heavy ions and protons in the energy region of 100–500 MeV per nucleon, the moving source model incorporating the knock-on process could be generally successful in reproducing the measured neutron spectra within a factor of two margin of accuracy. This phenomenological analytical equation is expressed having several parameters as functions of atomic number Z_p, mass number A_p, energy per nucleon E_p for projectile, and atomic number Z_T, mass number A_T for target. By inputting these basic data for projectile and target into this equation we can easily estimate the secondary neutron energy spectra at an emission angle of 0–90° for bombardment with heavy ions and protons in the aforementioned energy region. This method will be quite useful to estimate the neutron source term in the neutron shielding design of high energy proton and heavy ion accelerators.     

Superconductivity in W-containing diamond-like nanocomposite films

Superconductivity in a tungsten-containing carbon-oxide film was reported. The film with 500 nm thickness was deposited onto polycrystalline silicon oxides using chemical vapor deposition and the co-sputtering of a tungsten metal target. The bonding state of the carbon atoms and the macroscopic and microscopic crystal structure of the film were investigated by Raman spectroscopy, X-ray diffraction and transmission electron microscopy measurements. From the experimental results, we determined that this film essentially had an amorphous structure. The temperature dependence on resistivity was measured in the temperature range of 2–300 K. Resistive superconducting transition was observed at 3.8 K. The dc magnetizations were measured in the temperature range of 1.8–6.5 K. The diamagnetism resulting from a superconductive state was observed below 3.75 K, which is consistent with a resistive superconducting transition. It is thought that the finite sized clusters of the different superconductive transition temperatures cooperatively produce a macroscopic superconducting phenomenon.     

Examination of the role of oxygen in the photografting of methacrylic acid on a polyethylene film with a mixed solvent consisting of water and organic solvents

The photografting of methacrylic acid (MAA) on a linear low‐density polyethylene film (thickness = 30 μm) under air and nitrogen atmospheres was investigated at 60°C in mixed solvents consisting of water and an organic solvent, with xanthone as a photoinitiator. The organic solvents used were acetone, methanol, tetrahydrofuran, and dioxane. A maximum percentage of grafting occurred at a certain concentration of the organic solvent in the mixed solvent. This was observed for the systems under both air and nitrogen. The grafting reaction under air exhibited an induction period, but the rate of grafting after the period was greater than that under nitrogen. The formation of poly(ethylene peroxide)s by photoirradiation seemed to be a factor for the accelerated photografting under air. On the basis of attenuated total reflection infrared spectroscopy and scanning electron microscopy of the grafted film, the MAA‐grafted chains of the sample prepared under air tended to penetrate more deeply inside the film than those of the sample prepared under nitrogen. The resulting grafted films exhibited a pH‐responsive character: the grafted films shrank in an acidic medium but swelled in alkaline medium. This was evaluated from measurements of dimensional changes in the grafted films. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 992–998, 2003     

Development of a fast neutron radiography converter using wavelength-shifting fibers

A fluorescent converter for fast neutron radiography (FNR) comprising a scintillator and hydrogen-rich resin has been developed and applied to electronic imaging. The rate of the reaction between fast neutrons and the converter is increased by thickening the converter, but its opaqueness attenuates emitted light photons before they reach its surface. To improve the luminosity of a fluorescent converter for FNR, a novel type of converter was designed in which wavelength-shifting fibers were adopted to transport radiated light to the observation end face. The performance of the converter was compared with that of a polypropylene-based fluorescent converter in an experiment conducted at the fast-neutron-source reactor YAYOI in the University of Tokyo.     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.