Development of 170 GHz/500 kW gyrotron

A development of 170GHz/500kW level gyrotron was carried out as R&D work of ITER. The oscillation mode is TE_31,8. In a short pulse experiment, the maximum power of 750kW was achieved at 85kV/40A. The efficiency was 22%. In the depressed collector operation, 500kW/36%/50ms was obtained. The maximum efficiency of 40% was obtained at P_RF=470kW whereas the power decrease by the electron trapping was observed. Pulse extension was done up to 10s at P_RF=170kW with the depressed collector operation. The power was limited by the temperature increase of the output window.     

Fibre transmission distance determined by eye opening degradation due to selfphase modulation and group-velocity dispersion

Numerical analysis of IM signal propagation in an optical fibre is carried out taking selfphase modulation and group-velocity dispersion into account. The transmission distance yielding a prescribed eye opening penalty, in the normal dispersion region, is shown to be inversely proportional to the square root of the signal power.<>     

Preparation of SiB4±x and SiB6 plates by chemical vapour deposition of SiCl4 + B2H6 system

SiB_4±x and SiB₆ plates were prepared by chemical vapour deposition (CVD) using SiCl₄, B₂H₆ and H₂ gases under the conditions of deposition temperatures (T _dep) from 1323–1773 K, total gas pressures (P _tot) from 4–40 kPa and B/Si source gas ratio (m _B/Si=2B₂H₆/SiCl₄) from 0.2–2.8. The effects of CVD conditions on the morphology, structure and composition of the deposits were examined. High-purity and high-density SiB_4±x and SiB₆ plates about 1 mm thick were obtained at the deposition rates of 71 and 47 nm s⁻¹, respectively. The lattice parameter, composition and density of CVD SiB_4±x plates were dependent on their non-stoichiometry. The lattice parameter,a, was 0.6325 nm, butc ranged from 1.262–1.271 nm.The B/Si atomic ratio ranged from 3.1–5.0, and the density ranged from 2.39–2.45×10³ kg m⁻³. The CVD SiB₆ plates showed constant values of lattice parameters (a=1.444 nm,b=1.828 nm,c=0.9915 nm), composition (B/Si=6.0) and density (2.42×10³ kg m⁻³), independent of CVD conditions.     

Hydrothermal synthesis and in situ surface modification of boehmite nanoparticles in supercritical water

In situ surface modification of boehmite (AlOOH) nanoparticles during hydrothermal synthesis in supercritical water was examined by adding CH₃(CH₂)₄CHO and CH₃(CH₂)₅NH₂ as modifier reagents to the reactants. Changes in surface properties of the nanoparticles by surface modification was observed by FTIR, dispersion in solvents and TEM analyses, which demonstrated that reagents chemically binded onto the surface of the AlOOH nanoparticles. The results of SEM and TEM pictures show that the surface modification affects crystal growth and reduces the particle size and changes the morphology of the particles.     

High performance liquid chromatographic separation of stereoisomeric bile acids as their UV-sensitive esters

High performance liquid chromatographic separation of a series of mono-, di- and trihydroxylated 5β-cholanic acids which differ only in position and configuration of hydroxyl groups at positions C-3, C-7 and/or C-12, is reported. The C-24 free acids were derivatized to four different classes of UV-sensitive esters, i.e.,p-bromophenacyl (BP),m-methoxyphenacyl (MP), 4-nitrophthalimidemethyl (NPM) and 9-anthrylmethyl (AM) esters, and chromatographed on two, variants of C₁₈ reversed-phase columns (Nova-Pak C₁₈ and Zorbax ODS) with methanol-water systems as mobile phase. Separation efficiency and elution order of some isomeric pairs were influenced by both the structure of the C-24 ester groups and the nature of the columns used. Excellent chromatographic properties were found for those derivatives, particularly for the NPM esters.     

Generation of adaptive gait patterns for quadruped robot with CPG network including motor dynamic model

This paper describes the generation of adaptive gait patterns using new Central Pattern Generators (CPGs) including motor dynamic models for a quadruped robot under various environments. The CPGs act as the flexible oscillators of the joints and adjust joint angles to required values. The CPGs are interconnected with each other and sets of their coupling parameters are adjusted by a genetic algorithm so that the quadruped robot can realize stable and adequate gait patterns. Generation of gait patterns results in the formation of the CPG networks suitable for the formation of not only a straight walking pattern but also of rotating gait patterns. Experimental results demonstrate that the proposed CPG networks are effective for the automatic adjustment of the adaptive gait patterns for the tested quadruped robot under various environments. Furthermore, the target tracking control based on image processing is achieved by combining the general gait patterns. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(1): 35–43, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20225     

Tissue compatibility of polylactic acids in the skeletal site

This study was undertaken to examine the osseous tissue compatibility of polylactic acid (PLA) with properties of bioabsorbability and plasticity. Two kinds of granular PLA with different molecular weight (PLA-H: 28 000 MW, PLA-L: 10 600 MW) were implanted into rat tibiae and light microscopic sections were prepared at 1, 2, 4, 8, 16, and 24 weeks following surgery. The tissue compatibility of the PLAs was compared with that of hydroxyapatite (HAP) which is a non-absorbable biocompatible material. After implantation, both PLAs were gradually absorbed and replaced by marrow tissue at 24 weeks. PLA-H degraded slower than PLA-L. New bone formation was observed around each PLA by 4 weeks, and a vast amount of bone deposited on PLA-H at 16 weeks. Phagocytic reactions to the PLAs were noted, however, severe inflammation was not seen. HAP was not absorbed and bone surrounded it throughout the experiment. These results indicate good tissue compatibility of PLA as a bioabsorbable material at the skeletal site.     

Systematic analysis of neutron yields from thick targets bombarded by heavy ions and protons with moving source model

A simple phenomenological analysis using the moving source model has been performed on the neutron energy spectra produced by bombarding thick targets with high energy heavy ions which have been systematically measured at the Heavy-Ion Medical Accelerator (HIMAC) facility (located in Chiba, Japan) of the National Institute of Radiological Sciences (NIRS). For the bombardment of both heavy ions and protons in the energy region of 100–500 MeV per nucleon, the moving source model incorporating the knock-on process could be generally successful in reproducing the measured neutron spectra within a factor of two margin of accuracy. This phenomenological analytical equation is expressed having several parameters as functions of atomic number Z_p, mass number A_p, energy per nucleon E_p for projectile, and atomic number Z_T, mass number A_T for target. By inputting these basic data for projectile and target into this equation we can easily estimate the secondary neutron energy spectra at an emission angle of 0–90° for bombardment with heavy ions and protons in the aforementioned energy region. This method will be quite useful to estimate the neutron source term in the neutron shielding design of high energy proton and heavy ion accelerators.     

Superconductivity in W-containing diamond-like nanocomposite films

Superconductivity in a tungsten-containing carbon-oxide film was reported. The film with 500 nm thickness was deposited onto polycrystalline silicon oxides using chemical vapor deposition and the co-sputtering of a tungsten metal target. The bonding state of the carbon atoms and the macroscopic and microscopic crystal structure of the film were investigated by Raman spectroscopy, X-ray diffraction and transmission electron microscopy measurements. From the experimental results, we determined that this film essentially had an amorphous structure. The temperature dependence on resistivity was measured in the temperature range of 2–300 K. Resistive superconducting transition was observed at 3.8 K. The dc magnetizations were measured in the temperature range of 1.8–6.5 K. The diamagnetism resulting from a superconductive state was observed below 3.75 K, which is consistent with a resistive superconducting transition. It is thought that the finite sized clusters of the different superconductive transition temperatures cooperatively produce a macroscopic superconducting phenomenon.