Influence of Cu metal on the domain structure and carrier mobility in single-layer graphene

We demonstrate that domain structure of single-layer graphene grown by ambient pressure chemical vapor deposition is strongly dependent on the crystallinity of the Cu catalyst. Low energy electron microscopy analysis reveals that graphene grown using a Cu foil gives small and mis-oriented graphene domains with a number of domain boundaries. On the other hand, no apparent domain boundaries are observed in graphene grown over a heteroepitaxial Cu(111) film deposited on sapphire due to unified orientation of graphene hexagons. The difference in the domain structures is correlated with the difference in the crystal plane and grain structure of the Cu metal. The graphene film grown on the heteroepitaxial Cu film exhibits much higher carrier mobility than that grown on the Cu foil.     

Investigation of Precipitation Behavior in Age-Hardenable Cu-Ti Alloys by an Extraction-Based Approach

We investigated the precipitation processes in Cu-4 mol pct Ti alloy specimens aged at 723 K (450 °C), by means of X-ray diffraction and chemical analyses of the precipitates extracted from the parent alloy specimens. Aging-induced precipitate particles of a spinodally decomposed disorder, α′; those of a metastable order, β′-Cu₄Ti; and those of a stable order, β-Cu₄Ti, were continuously formed in the aged specimens. The extraction of the precipitate particles from the aged specimens by submergence in a nitric solution allowed for not only the structural analyses of the constituent precipitate phases but also the quantitative evaluation of their chemical compositions and volume fractions. Early during the aging process, the supersaturated Cu solid solution decomposes spinodally in a continuous manner, and an unstable disorder, α′, appears. Then, fine needle-shaped β′-Cu₄Ti particles, which have a Ti content of approximately 37.5 mol pct, form in the Cu matrix. During prolonged aging, coarse cellular components composed of the terminal Cu solid solution and stable β-Cu₄Ti particles which have a Ti content of 20.5 mol pct nucleate and grow, primarily in the grain boundaries, at the expense of the metastable β′-Cu₄Ti particles. The volume fraction of the β′-Cu₄Ti particles in the alloy reaches a maximum of approximately 1.7 pct after aging for 24 hours, while that of the β-Cu₄Ti particles increases steadily to more than 18 pct after 480 hours. The volume fraction of the fine β′-Cu₄Ti particles in the alloy specimens remained constant throughout the age-hardening, indicating that the hardening is primarily owing to the fine dispersion of the β′-Cu₄Ti particles and not because of the large volume fraction of coarse β-Cu₄Ti particles.     

Preparation of ultrafine polyurethane fiber web by laser‐electrospinning combined with air blowing

Thermoplastic polyurethane fiber webs were prepared using a laser‐heated electrospinning process combined with air blowing. The effect of spinning conditions such as air flow rate and air temperature on fiber diameter and molecular weight was investigated. Although the average fiber diameter decreased with increased air flow rate at each air temperature, the diameter increased when the air flow rate was >15 NL min^?1. In addition, the fiber was comparatively thicker with an increase in the air temperature. The variation in the fiber diameter tends to increase with the air flow rate, and a reduction in the molecular weight of the fiber by thermal degradation was suppressed. The thinnest and most uniform fiber with a diameter of 0.9 µm and a diameter coefficient variation of 15% was obtained at an air temperature of 25°C under an air flow rate of 15 NL min^?1. This fiber also had a minimum of decreased molecular weight. POLYM. ENG. SCI., 54:2605–2609, 2014. © 2013 Society of Plastics Engineers     

Correlations of Hepatic Hemodynamics,Liver Function,and Fibrosis Markers in Nonalcoholic Fatty Liver Disease: Comparison with Chronic Hepatitis Related to Hepatitis C Virus

The progression of chronic liver disease differs by etiology. The aim of this study was to elucidate the difference in disease progression between chronic hepatitis C (CHC) and nonalcoholic fatty liver disease (NAFLD) by means of fibrosis markers, liver function, and hepatic tissue blood flow (TBF). Xenon computed tomography (Xe-CT) was performed in 139 patients with NAFLD and 152 patients with CHC (including liver cirrhosis (LC)). The cutoff values for fibrosis markers were compared between NAFLD and CHC, and correlations between hepatic TBF and liver function tests were examined at each fibrosis stage. The cutoff values for detection of the advanced fibrosis stage were lower in NAFLD than in CHC. Although portal venous TBF (PVTBF) correlated with liver function tests, PVTBF in initial LC caused by nonalcoholic steatohepatitis (NASH-LC) was significantly lower than that in hepatitis C virus (C-LC) (p = 0.014). Conversely, the liver function tests in NASH-LC were higher than those in C-LC (p < 0.05). It is important to recognize the difference between NAFLD and CHC. We concluded that changes in hepatic blood flow occurred during the earliest stage of hepatic fibrosis in patients with NAFLD; therefore, patients with NAFLD need to be followed carefully.     

Fracture behaviour and numerical study of resistance spot welded joints in high-strength steel sheet

Cross tension tests of resistance spot welded joints with varying nugget diameter were carried out using 980 MPa high strength steel sheet of 1.6 mm thickness. In proportion, as nugget diameter increased from 3√t to 5√t (where t is thickness), cross tension strength (CTS) increased while fracture morphology simultaneously transferred from interface fracture to full plug fracture. In cases of interface fracture, circumferential crack initiation due to separation of the corona bond arose at an early stage of loading. The crack opening process without propagation was recognized until just before fracture and then the crack propagated to the nugget immediately in a brittle manner around CTS. In full plug fracture, main ductile crack initiation from the notch-like part at the end of sheet separation occurred with the sub-crack initiated at an early stage. The ductile crack propagated toward the HAZ and base material to form full plug fracture. The mode I stress intensity factor was considered as a suitable fracture parameter because the circumferential crack behaved pre-crack for brittle fracture in the nugget region at the final stage. Based on the FE analysis, the mode I stress intensity factor was calculated as 116 MPa √m at CTS as fracture toughness for the nugget. With respect to full plug fracture, ductile crack initiation behaviour from the notch-like part was expressed by concentration of equivalent plastic strain. On the assumption that the ductile crack arose in critical value of equivalent plastic strain, the value was calculated as 0.34 by FE analysis. Reasonable interpretation for interface fracture and full plug fracture in the resistance spot welded joint was proposed due to first crack initiation by stress concentration, brittle fracture by using mode I stress intensity factor, and ductile crack initiation by using equivalent plastic strain.     

Investigation report of geotechnical disaster on river area due to typhoon landfall three times on Okhotsk region,Hokkaido, Japan

For one week from August 17 to 23, 2016, three consecutive typhoons made landfall in Hokkaido for the first time on record. These typhoons and the front they stimulated brought record-breaking torrential rain over the eastern part of Hokkaido. To investigate the damage to grounds and rivers resulting from this rainfall, the Japan Society of Civil Engineers (JSCE) and the Japanese Geotechnical Society (JGS) formed a disaster research group to conduct an investigation. This report provides the results of the investigation into damage to the grounds of areas along the Tokoro River of the Okhotsk region, Hokkaido, that suffered from this tremendous and diverse disaster. Specifically, the report describes the situation of the levees which were broken and eroded by the overflowing water, the shape of the levee bodies, the levee body soil properties examined by observation of the sections, as well as the occurrence of sand boiling and air blows. The washout of road embankments as well as damage to road bridge mounting fills and abutment backfills were also investigated. The investigation has demonstrated the need to clarify the resistance of the abutment backfills and levee bodies to flowing water as well as the geotechnical predominant factors in order to clarify the mechanisms behind erosion and washout, the need to review new measures that allow for the scale of sand boiling and resultant changes in levee body stability, and the fact that the existing embankments were able to temporarily suppress the flooding water which had spilled over from the river. Furthermore, although it has been identified that the findings of a study on an embankment washout associated with a tsunami can be applied to measures taken against the overflowing water, it has also been found necessary to clarify the predominant geotechnical factors using model tests and to use a more sophisticated analytical approach to establish a geotechnical stability review as soon as possible in order to prevent the levees and embankments from being eroded and washed out due to overflowing water.     

Polypropylene plasticization and photodegradation with a TiO2/poly(ethylene oxide)/methyl linoleate paint photocatalyst system

The photodegradation of polypropylene (PP) film was performed by a TiO₂/polyethylene oxide (PEO)/plant oil paint photocatalyst system. The photodegradation underwent two stages of development as follows: Initially PP reacted with linoleic acid radical originated from the photoreaction of plant oil component. Second, the linoleic acid graft‐polymer was decomposed, and then PP chain scission was caused. The process was studied using methyl linoleate (ML) in detail. The melting point of the 24 h‐photodegraded PP slightly decreased, and those of the 48 h‐ and 96 h‐ones drastically did as compared with the pristine PP. The crystallinity (χ_c) decreased at the 48 h photodegradation time and drastically increased at the 96 h one. The 24 h‐photodegraded PP showed the 77% Young's modulus, 88% tensile strength, and 103% strain at break values to those of the pristine PP. The ML graft‐polymerization and decomposition brought about the PP plasticizing and chemi‐crystallization, causing the PP degradation. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39909.     

Influence of metal ion concentration in the glycol mediated synthesis of Gd2O3:Eu nanophosphor

The solvothermal synthesis of highly luminescent and homogeneous Gd₂O₃:Eu³⁺ nanophosphor using diethylene glycol as medium, followed by controlled combustion with citric acid as fuel is reported. The influence of concentrations of carboxylic acid and metal cations on the structure, morphology and luminescence properties are investigated in detail. The microscopic investigations indicate the nanocrystalline nature and the strong influence of cation concentration on the size, shape and agglomeration of the particles. It is found that increase in concentration of metal cations lead to the reduction in agglomeration of nanophosphors. The large value of intensity parameter Ω_2, suggested that Eu³⁺ ions reside in a more asymmetric environment, resulted in intense emission due to ⁵D₀–⁷F₂ electric dipole transition. Emission decay analysis of the samples exhibited one exponential nature. The samples prepared under optimum conditions showed a quantum efficiency of 78.63% and a moderately high life time of 1.217 ms.     

Nucleotide sequences of alcohol acetyltransferase genes from lager brewing yeast,Saccharomyces carlsbergensis

The nucleotide sequences of alcohol acetyltransferase genes isolated from lager brewing yeast, Saccharomyces carlsbergensis have been determined. S. carlsbergensis has one ATF1 gene and another homologous gene, the Lg-ATF1 gene. There was a high degree of homology between the amino acid sequences deduced for the ATF1 protein and the Lg-ATF1 protein (75·7%), but the N-terminal region has a relatively low degree of homology. Southern analysis and contour-clamped homogeneous electric field analysis of Saccharomyces strains suggest that the ATF1 gene is located on chromosome XV in S. cerevisiae and that the Lg-ATF1 gene might originate from the ‘non-S. cerevisiae’ genome of S. carlsbergensis, which is similar to that of S. bayanus and S. pastorianus. The nucleotide sequence data reported in this paper will appear in the DDBJ, EMBL and GenBank data banks with the Accession Numbers D63449 (ATF1) and D63450 (Lg-ATF1).