Investigation and consideration on landslide zoning of multiple slope failures and debris flows of 2014 disaster in Hiroshima,Japan

This study was intended to examine the mechanism of multiple slope failures and debris flows that occurred in the outskirts of Hiroshima on 20th August 2014. A field survey of the mountain stream where large-scale damage was incurred was carried out and the characteristics of debris flows which made serious damages were investigated. There were five findings of this study. (1) The initiation of debris flows was not limited to thin and planar shallow failures, but also showed V or U shapes, where the eroded sediments seemed to be pushed out by artesian water, and the eroded depth exceeded several meters at many locations. (2) There were areas with high permeability, such as faults, fracture zones, and joints in Mt. Abusan. It is inferred that the constantly present groundwater in these areas became artesian water because of a large amount of rainfall in upstream locations. This quickly destabilized the slopes on a large scale. (3) There were at least three estimated debris flows at the mountain stream above Midorigaoka prefectural apartments in Yagi 3-Chome, where the worst damage occurred. The mountain stream near Abu-no-Sato housing complex also had multiple debris flows. Here, the secondary debris flow changed its flow path because of the presence of sediments from an earlier debris flow. (4) The actual volumes of flowed mass were much larger than that predicted at 11 of the 18 mountain streams in Midori-i and Yagi districts. The volume of the mass of five of these mountain streams was more than twice the estimated volume. It is necessary to modify the method of calculating the volume of unstable sediments in the mountain stream. (5) It was found that the devastating damage of buildings and human lives took place in the areas well beyond the special restricted zones. The present method to designate the special restricted zone must be revised considering such problems as the underestimation of the volume of unstable sediments, the assumptions of a single debris flow and on the direction of debris flow, and the effect of the difference on rock and soil types.     

Rh/γ-Al2O3 Catalytic Layer Integrated with Sol–Gel Synthesized Microporous Silica Membrane for Compact Membrane Reactor Applications

An efficient and compact catalytic membrane reactor for reforming of CH₄ was developed by integrating a hydrogen perm-selective silica membrane with an Rh/-Al₂O₃ catalyst layer. The catalytic layer was sandwiched between the outer surface of the -Al₂O₃ support tube and the silica membrane with an aim of improving the heat and mass transfer rates through the system and to simplify the reactor geometry. The system showed improved efficiency for reforming of CH₄ at comparatively lower operating temperatures and steam to C molar ratios than the conventional fixed-bed steam reforming systems. Under optimized conditions, a nearly 25-30% improvement from the equilibrium conversion level was achieved as a result of abstraction of hydrogen from the product stream by the silica membrane integrated with the catalyst layer. The performance of the system was evaluated as a function of various process parameters. Because of the compactness and efficiency, the present system emerges as a promising alternative to the conventional membrane reactors, which possess separate catalytic and membrane units.     

Corrosion characteristics of reduced activation ferritic steel, JLF-1 (8.92Cr–2W) in molten salts Flibe and Flinak

Static corrosion tests were performed in molten salts, LiF–BeF₂ (Flibe) and LiF–NaF–KF (Flinak), at 500 °C and 600 °C for 1000 h. The purpose is to investigate the corrosion characteristics of reduced activation ferritic steels, JLF-1 (8.92Cr–2W) in the fluids. The concentration of hydrogen fluoride (HF) in the fluids was measured by slurry pH titration method before and after the exposure. The HF concentration determined the fluoridation potential. The corrosion was mainly caused by dissolution of Fe and Cr into the fluids due to fluoridation and/or electrochemical corrosion. Carbon on the surface might be dissolved into the fluids due to the corrosion, and this resulted to the decrease of carbide on the surface. The corrosion depth of the JLF-1 specimen, which was obtained from the weight losses, was 0.637 μm in Flibe at 600 °C and 6.73 μm in Flinak at 600 °C.     

Compatibility of erbium oxide coating with liquid lithium–lead alloy and corrosion protection effect of iron layer

Li–Pb compatibility of Er₂O₃ and Er₂O₃-Fe two-layer coatings has been explored for an understanding of corrosion behaviors and effects of the protection layer. The coatings were peeled off after static Li–Pb immersion test at 600 °C due to the degradation of adhesion between the coating–substrate interface. A loss of Er and then subsequent corrosion of Er₂O₃ were shown after immersion at 500 °C for 500 and 1505 h. However, the outer Fe layer played a role to decrease corrosion rate of the coatings by comparing with the results of Er₂O₃ single layer coatings. Deuterium permeation measurements after corrosion tests at 500 °C showed that the Er₂O₃ coatings kept permeation reduction factors of 10²–10³ after 500 h immersion, but seriously degraded after 1505 h immersion. Corrosion mechanisms suggest that corrosion protection properties will be modified by an optimization of the outer Fe layer and a control of oxygen concentration in Li–Pb.     

Irradiation effects of boron carbide used as control rod elements in fast breeder reactors

The paper describes radiation effects on 8₄C pellets used as control rod elements in the Enrico Fermi Fast Breeder Reactor. Pellet swelling (Δ$\text{V/V}$) caused by irradiation was less than 1% in which crystal lattice swelling was less than 20%. Many microcracks, a main cause of pellet swelling, appeared in the irradiated pellets. The production of microcracks was related to graphite precipitation in the pellets before irradiation. Open pores which did not exist in the unirradiated pellets were formed in the irradiated ones. In a unit cell of B₄C, the α-axis elongated by 0.025 Å and the $\text{c-}\text{axis}$ shrank by 0.07 Å by irradiation. Moreover, we found three recovery stages which were from room temperature to 400°C, from 400 to 750°C and from 850 to 1100°C. The recovery mechanisms in the irradiated pellets are discussed in terms of the helium behavior.     

A comparative study of microbubble generation by mechanical agitation and sonication

As focus on the potential applications of microbubbles increases, information about the efficiency of generation methods and their effects on the properties and stability of microbubbles is crucial in the selection of an appropriate method to generate microbubbles with the desired properties. This paper evaluates the generation efficiencies of two commonly used methods, mechanical agitation and sonication, in two surfactant systems. The results demonstrated that sonication was more effective than mechanical agitation in the generation of microbubbles in terms of higher gas hold-up, smaller bubble size, and larger interfacial area. Analysis of the changes in bubble size over time revealed that the existence of a critical diameter for the shrinkage of microbubbles. The behavior of microbubbles and the critical diameter depended on the generation method employed and the surfactant used.

Industrial relevance

Microbubble technology has gradually become accepted as a cost-effective and environmentally friendly technology with great potential within almost every field of the food industry. Selection of a suitable method to generate microbubbles with the desired properties is crucial. Mechanical agitation and sonication are two commonly used methods for microbubble generation. However, systematic information on their generation efficiency and effects on the properties of microbubbles is not available. Thus, a comparative study was conducted in this paper.     

An absolute requirement of fructose 1,6-bisphosphate for the Lactobacillus caseiL-lactate dehydrogenase activity induced by a single amino acid substitution

Lactobacillus casei allosteric L-lactate dehydrogenase (L-LDH)absolutely requires fructose 1,6-bisphosphate [Fru(1,6)P2] forits catalytic activity under neutral conditions, but exhibitsmarked catalytic activity in the absence of Fru(1,6)P₂ underacidic conditions through the homotropic activation effect ofsubstrate pyruvate. In this enzyme, a single amino acid replacement,i.e. that of His205 conserved in the Fru(1,6)P₂-binding siteof certain allosteric L-LDHs of lactic acid bacteria with Thr,did not induce a marked loss of the activation effect of Fru(1,6)P₂or divalent metal ions, which are potent activators that improvethe activation function of Fru(1,6)P₂ under neutral conditions.However, this replacement induced a great loss of the Fru(1,6)P₂-independentactivation effect of pyruvate or pyruvate analogs under acidicconditions, consequently indicating an absolute Fru(1,6)P₂ requirementfor the enzyme activity. The replacement also induced a significantreduction in the pH-dependent sensitivity of the enzyme to Fru(1,6)P₂,through a slight decrease and increase of the Fru(1,6)P₂ sensitivityunder acidic and neutral conditions, respectively, indicatingthat His205 is also largely involved in the pH-dependent sensitivityof L.casei L-LDH to Fru(1,6)P₂. The role of His205 in the allostericregulation of the enzyme is discussed on the basis of the knowncrystal structures of L-LDHs.     

Fabrication of Nonadditive Mica Ceramics by Hot Isostatic Processing

Powder compacts of synthetic mica (fluorphlogopite) encapsulated in a boro–silicate glass tube were isostatically hot–pressed in a Roy–Tuttle–type pressure vessel. Synthetic mica was sintered to a density of 2.60 g/cm³ (91.2% of theoretical density) without additives under 98 MPa of water at 800°C for 45 min.