Design and modification of steam generator safety system of FBR MONJU

MONJU is a prototype fast breeder reactor (FBR) in Japan. The sodium–water reaction in the steam generator (SG) is one of the important safety assessment items for a sodium cooled reactor like MONJU. MONJU is equipped with hydrogen gas detectors for the small water leak detection, gas pressure gauges for the medium leak and sensors of rupture discs for the large leak. As a design basis accident, one tube failure then failure propagation of neighboring three tubes is assessed to verify the structural integrity of the secondary components. A latest evaluation method on the design margin against the overheating tube rupture showed that the present SG system had not an enough margin in the worst case. For improving the margin, it needs to shorten the time of the sodium–water reaction by earlier water leak detection in the SG and sooner water ejection from the SG tubes. Therefore, MONJU is now carrying out the following modification works: (1) addition of steam relief valves, (2) addition of a gas pressure gauge with changing the interlock logic and lowering the trigger level, (3) reducing the opening of the valves on the SG gas flow line to the dump tank because of earlier detection for the pressure rise. After this modification, the design margin of the SG system will be sufficiently improved.     

Synthesis and characterization of PEFC membranes based on fluorinated-polymer-alloy using pre-soft-EB grafting method

Polymer electrolyte fuel cell (PEFC) membranes based on thin film of crosslinked perfluorinated polymer-alloys (RX-FA) have been fabricated by soft electron beam (soft-EB) grafting with styrene monomers using soft-EB irradiation under nitrogen atmosphere at room temperature (RT). The characteristic properties of styrene-grafted materials (GRX-FA) and sulfonated materials (SRX-FA) have been measured by differential scanning calorimetry (DSC) and FT-IR spectroscopy, ionic conductivity and so on. The glass transition temperatures (dry state) of all obtained SRX-FA were about 105 ± 1 °C, which are higher than Nafion^®. The ion exchange capacities of SRX-FA have been achieved about 3.3 meq/g (dry). The ionic conductivity of obtained SRX-FA has showed about 0.17 S/cm at 60 °C with relative humidity (RH) of ∼95%. The ionic conductivities of the obtained SRX-FA were higher than that of conventional perfluoro-sulfonic acid membranes (PFSA). Fabricated membrane electrode assemblies (MEAs) based on the obtained SRX-FA have shown encouraging performance in the PEFC, compared with the conventional PFSA. The power density of obtained MEAs based on the SRX-FA was about 330-340 mW/cm² under 500 mA/cm² at 60 °C operation. Moreover, the maximum power densities of obtained MEAs based on the SRX-FA shows about 630 mW/cm² at 60 °C. On the other hand, the power density at 500 mA/cm² and maximum power density of MEA based on Nafion^®112 were about 320 and 590 mW/cm² at 60 °C. Thus, the power density of the obtained SRX-FA was higher than that of conventional PFSA.     

A radio frequency identification implanted in a tooth can communicate with the outside world.

A radio frequency identification (RFID) transponder covering the 13.56 MHz band was adapted to minimize its volume so that it could be placed in the pulp chamber of an endodontically treated human tooth. The minimized transponder had a maximum communication distance of 30 mm. In an animal experiment, the transponder was fixed in the cavity of a mandibular canine of a dog. An RFID reader positioned close to the dog's face could communicate with the transponder in the dog's tooth. In certain cases, the system is applicable for the personal identification procedures for hospitalized patients instead of an identification wristband.     

Synthesis of Liquid Crystalline Organometallic Poly(arylene)s Containing 1,3-Type (η4-Cyclobutadiene)cobalt Moieties in the Main Chain

Novel organometallic poly(arylene)s containing 1,3-type (cyclobutadiene)cobalt moieties in the main chain were prepared by the Ni(0)-mediated dehalogenative polycondensation of monomers having (cyclobutadiene)cobalt moieties. The resulting poly(arylene)s were partly soluble in organic solvents and the number-average molecular weights (M _n) of soluble fractions were estimated to be 16,700–22,000 by GPC. The polymers showed the formation of a -conjugated structure, good solubility in common organic solvents, and thermotropic liquid crystallinity.     

A 50-kDa variant form of human surfactant protein D

The dominant form of human surfactant protein D (SP-D) is a multimeric collagenous glycoprotein composed of monomeric subunits that have a molecular mass of 43 kDa under reducing conditions. However, in evaluating monoclonal antibodies to human SP-D, an additional monomeric subunit was identified with a reduced molecular mass of 50 kDa. This 50-kDa variant was detected in approximately half of the samples evaluated and was found in lavage fluid from normal subjects, patients with alveolar proteinosis or idiopathic pulmonary fibrosis and in amniotic fluid. This 50-kDa variant had the same amino-terminal sequence, amino acid composition and apparent size of the carboxy-terminal collagenase-resistant fragment (20 kDa) as the 43-kDa subunit. The major difference was in the amino-terminal portion of the molecule and was due to altered glycosylation, as determined by carbohydrate staining, chemical deglycosylation, treatment with N-glycanase and neuraminidase and reduced signals for threonine at positions 5, 9 and 10 during amino-terminal sequencing. After gel filtration chromatography, the 50-kDa form was not present in the high molecular weight fraction, which is commonly used in purification of SP-D, but was found only in the smaller molecular weight fraction of monomers and trimers of SP-D. In conclusion, the 50 kDa-form of surfactant protein D is produced by post-translational glycosylation and does not form higher ordered oligomers, but its precise physiological function remains to be determined.     

The action modes of an extracellular beta-1,3-glucanase isolated from Bacillus clausii NM-1 on beta-1,3-glucooligosaccharides

The mode of action of an extracellular -1,3-glucanase from Bacillus clausii NM-1 on beta-1,3-3glucooligosaccharides and their alditols was studied. The enzyme could not hydrolyze laminaribiose or laminaritriose. beta-1,3-Glucooligosaccharides higher than laminarihexaose were rapidly hydrolyzed, while laminaritetraose was slowly hydrolyzed. The k(cat)/K(m) ratios for a series of beta-1,3-glucooligosaccharides from laminaritetraose to laminariheptaose showed that the substrate binding site of the enzyme covered a wide range of beta-1,3-glucooligosaccharides having six glucose residues. The action pattern of the enzyme on the alditols corresponding to each laminarioligosaccharide suggested that the catalytic site of the enzyme existed between the third and fourth glucose residue from the non-reducing terminal. The value of k(cat)/K(m) also suggested that the sixth binding position contributed to the catalytic efficiency and stability.     

Electrical communication between glucose oxidase and electrodes mediated by phenothiazine-labeled poly(ethylene oxide) bonded to lysine residues on the enzyme surface

A series of glucose oxidase (GOx) hybrids (GOx-phe-nothiazine-labeled poly(ethylene oxide) (PT-PEO)) capable of direct electrical communication with electrodes is synthesized by covalently modifying PT-PEO to lysine residues on the enzyme surface. The length of the PEO chain and the number of PT groups are systematically altered. After the PT-PEO modification, all the hybrids maintain more than 50% of enzyme activity relative to that of native GOx, although loss of the activity becomes greater with increasing PEO chain length. The catalytic current, i(cat), is observed at a potential more positive than 0.55 V after the addition of glucose, due to the intramolecular electron transfer (El) from reduced forms of flavin adenine dinucletide (FADH2/FADH) to PT+ that are electrogenerated at the electrode. The i(cat) value increases with the number of PT groups, indicating that most of the modified PT groups act as mediators. The magnitude of the i(cat) increase depends on the PEO chain length and reveals a maximum for PT-PEO with the molecular weight of 3,000. In contrast, the i(cat) is almost constant for GOx-2-(10-phenothiazyl)propionic acid (PT-PA) hybrids with more than two PT groups synthesized by covalently modifying PT-PA to surface lysines, indicating that only a few key PT groups function as mediators. The maximum rate constant (130 s(-1)) for the ET from FADH2/FADH to PT+ is obtained for the GOx hybrid modified with five PT-PEO groups with the molecular weight of 3,000.     

A core-shell-type fluorescent nanosphere possessing reactive poly(ethylene glycol) tethered chains on the surface for zeptomole detection of protein in time-resolved fluorometric immunoassay

To increase the sensitivity and to depress the nonspecific binding in biochemical assays, a new core-shell-type fluorescent nanosphere (106.7 nm) covalently conjugated with antibody was prepared. The core-shell-type nanosphere was constructed by dispersion radical polymerization of styrene in the presence of heterotelechelic poly(ethylene glycol) (PEG) macromonomer, which has a polymerizable vinylbenzyl group at one end and a primary amino group at the other chain end and used as well as a surfactant. The resulting nanosphere had PEG tethered chains on the surface, which possesses a primary amino group at the distal end of the PEG chain (NH(2) nanosphere). The fluorescent NH(2) nanosphere was constructed by incorporating fluorescent europium chelates with beta-diketonate ligands in the core of the NH(2) nanosphere by means of a physical entrapment method. The primary amino groups on the fluorescent NH(2) nanosphere were then converted to maleimide groups using a hetero cross-linker. The resulting nanosphere had maleimide groups on the surface (maleimide nanosphere), onto which proteins having SH group in the molecule could be covalently conjugated quantitatively without any denaturation of the proteins under the milder reaction condition. The applicability of the fluorescent nanosphere was tested in a model sandwich immunoassay for alpha-fetoprotein (AFP) determination. Anti-human AFP Fab' fragment was covalently conjugated onto the maleimide nanosphere (Fab' nanosphere), and it was used for the solid-phase time-resolved fluorometric immunoassay of AFP. The detection limit (mean + 2 SD) was 0.040 pg/mL or 57.1 zmol (57.1 x 10(-)(21) mol, M(w,AFP) = 70000) for AFP. The imprecision (concentration CV) over the whole assay range was 1.1% (100 pg/mL) - 17.1% (0.1 pg/mL), even though with this conjugation of antibody to the nanosphere, the nonspecific binding was practically negligible (0.0008%) and even when approximately 1.9 x 10(9) particles of the Fab' nanosphere were applied to the microtitration well.     

Compact effector optics for processing in limited physical access situations

A major advantage of fiber-optic beam delivery in laser materials processing is the ability to guide the laser power to the location where it is needed, leaving the laser itself remote and protected from the process. This is of special importance if the processing is to be performed in a hazardous environment. Particular problems are faced by the nuclear industry where weld repair and surface treatment work are required inside radioactive installations. By use of fiber beam delivery, only part of the delivery system and effector optics become contaminated, but the expensive laser system does not. However, in many cases the region where repair is required is not only radioactive but has only limited physical access, e.g., inside tubes or into corners, which prevents use of standard effector optics. We present a new design to deal with such constraints of a 2-mm outer diameter employing a hollow waveguide and gas shielding. This design is optically characterized and its performance assessed in welding and surface treatment applications. The potential of this compact effector optics in limited physical access situations is clearly demonstrated.     

Beam homogenizer for hollow-fiber delivery system of excimer laser light

A beam homogenizer for a hollow-fiber-based, UV laser delivery system is proposed. A rectangular glass waveguide with an inner aluminum coating that has a 1-mm square cross section is attached at the output end of the circular-core hollow fiber with a 1-mm inner diameter. The rectangular waveguide generates a number of higher-order modes and results in a uniform top-hat profile. The configuration of the waveguide is designed by a ray-tracing technique so that both the low transmission loss and the high uniformity in the output beam are obtained. The fabricated waveguide shows a low loss of 0.4 dB, and the intensity variation coefficient is 7%. The output beam from the rectangular waveguide is expanded by a lens to the size larger than 10-mm square. It is also shown that the profile does not change with the bending condition.