Partial Oxidation of Methane to Syngas over Calcined Ni–Mg/Al Layered Double Hydroxides

The catalytic partial oxidation of CH₄ to syngas was carried out over an Ni–Mg/Al mixed-oxide catalyst prepared from layered double hydroxide-type precursors. The catalysts were characterized by XRD, TPR, UV-DRS, XRF, BET and CHNS analysis. The effects of the catalyst composition and the calcination temperature on the catalytic performance and the extent of catalyst deactivation were investigated. Ni–Mg/Al oxide catalysts converted CH₄ into syngas efficiently with high selectivity. The catalyst performance was strongly related to the Ni particle size and the calcination temperature. The catalysts that were calcined at higher temperature exhibited a better catalytic performance. In conclusion, the NiAl₂O₄ spinel phase had a positive effect on the stability of the catalyst.     

Processabilities and mechanical properties of surlyn-treated starch/LDPE blends

The esterification of the hydroxyl group of starch with DuPont Surlyn was considered as pretreatment method of starch before blending with polyolefins. In treating starch with Surlyn, two different raction conditions were taken to optimize reaction conditions. First, the esterification reaction was carried out in 110°C xylene with oleic acid as a catalyst. Second, the reaction out in a 90°C mixture of deionized water and xylene with ceric ammonium nitrate(CAN) as an initiator. Starch granules would be swollen above the gelatinization temperature in water. In both cases starch was midified by Surlyn to have good compatibility with low-density polyethylene (LDPE). The mechanical and theological properties were examined for blends of the treated starch and LDPE. This system may be one of the biodegradable polymer blends that sufficiently retain properties as a packaging film.     

SEQUENTIAL LOOP CLOSING IDENTIFICATION OF MULTIVARIABLE PROCESSES USING THE BIASED RELAY FEEDBACK METHOD

Each controller in multiloop control systems for multivariable processes can be tuned sequentially with the ultimate information for the paired input and output while former loops have been closed, and hence, single-input single-output autotuning methods can be applied. In this sequential autotuning for multiloop control systems, several iterations are usually required for better control performances. Especially when pairings are undesirable, the autotuning sequences should be repeated with correct pairings, which result in long field experiments. Here, to avoid this drawback, a simple method to identify process models while loops are being sequentially tuned is proposed. The identified models can be used to correct pairings of multiloop control systems and to improve tuning performances without several field iterations. In addition, they can be used to obtain model-based control systems such as decoupling control systems.     

Preparation and characterization of rubber‐toughened poly(trimethylene terephthalate)/organoclay nanocomposite

Rubber‐toughened poly(trimethylene terephthalate) (PTT)–organoclay nanocomposite (RTPTTCN) was prepared by a melt mixing technique. The rubber‐toughened PTT (RTPTT) was made by blending it with ethylene propylene diene terpolymer (EPDM) and with a small amount of maleated EPDM as a compatibilizer. XRD and TEM analysis indicated that the RTPTTCN forms a partially exfoliated nanocomposite. It was observed from SEM analysis that the clay nanoparticles induced a reduction of rubber particle size in the PTT matrix. Tensile and dynamic mechanical analysis indicated that the clay nanoparticles enhance the stiffness of the RTPTT without adversely affecting its toughness. Melt rheological studies revealed that the nanocomposites exhibited strong shear thinning behavior, and a percolated network of the clay particles was formed. It was also observed from DSC that the clay nanoparticles caused an increase in the nonisothermal crystallization temperature of the PTT. POLYM. ENG. SCI., 47:863–870, 2007. © 2007 Society of Plastics Engineers     

The Interlaminar Bond Strength of Flexible Polymer-Metal Laminates

An alternative test method to the traditional 180° “T” peel test has been developed for the measurement of interlaminar bonding in three-ply (polyester/aluminium/polypropylene) flexible-packaging, laminate materials. The new test is thought to involve mixed mode I (opening) and mode II (shearing) failure, and takes into account the yielding of the polypropylene layer during testing. The method allows more direct comparisons between materials to be made, and allows the measurement of strong bonds, where a peel test would result in yield or fracture of the substrate arms before debonding.     

Synthesis and characterization of novel aromatic condensation polymers containing rigid benzoxazole pendent groups

A new aromatic diamine monomer containing benzoxazole substituents was prepared by a multistep synthesis starting from 1,4‐dibromo‐2,5‐difluorobenzene. The diamine was polymerized with commercial aromatic dianhydride or dicarboxylic acid chloride monomers to provide several different poly(amic acid)s and polyamides with their inherent viscosities in the range of 0.24–0.46 dL/g. Thermal properties of these polymers including thermal imidization of poly(amic acid)s into polyimides were investigated by using FTIR, DSC, and TGA. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 178–185, 2004     

Effect of solution properties on nanofibrous structure of electrospun poly(lactic‐co‐glycolic acid)

Electrospinning of poly(lactic‐co‐glycolic acid) (PLGA) in chloroform or 1,1,1,3,3,3‐hexafluoro‐2‐propanol (HFIP) was investigated, focusing on its solution parameters, to develop nonwoven biodegradable nanofibrous structures for tissue engineering. PLGA nanofibers were obtained by electrospinning of 15 wt % PLGA solution and the resulting average fiber diameters were varied with the range of 270–760 nm, depending on solution property. When small amounts of benzyl triethylammonium chloride (BTEAC) was added to the PLGA/chloroform solution, the average diameter was decreased from 760 to 450 nm and the fibers were densely amounted in a straight shape. In addition, the average fiber diameter (270 nm) of nanofibers electrospun from polar HFIP solvent was much smaller than that (760 nm) of nanofibers electrospun from nonpolar chloroform solvent. Therefore, it could be concluded that conductivity or dielectric constant of the PLGA solution was a major parameter affecting the morphology and diameter of the electrospun PLGA fibers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1214–1221, 2006     

A study on the deposition of pyrolytic carbons from hydrocarbons

A new method for forming isotropic, laminar, and columnar pyrolytic carbons is proposed. For this, a low RPM (below 2.4 rpm) tumbling bed has been used to deposit pyrolytic carbons from hydrocarbon gases. All deposits were made on graphite substrates from propane and methane at a constant temperature of 1200°C. The microstructures of the pyrolytic carbons deposited were dependent on the flow pattern of the reactant gas, the rpm of the reactor, the hydrocarbon concentration, the nature of the hydrocarbon, and the geometry of the bed. Isotropic pyrolytic carbon is formed under deposition conditions where homogeneous nucleation occurs in the gas phase and at the gas flow conditions where the gas-borne droplets can collide on the substrate. Laminar carbon is formed under deposition conditions where homogeneous nucleation does not occur in the gas phase and at gas flow conditions where the carbon species existing in the bulk of the gas phase can collide on the substrate. Columnar carbon is formed when any carbon products existing in the bulk of the gas phase cannot collide on the substrate. The suggested deposition mechanism can also be applied to pyrolytic carbons deposited in a fluidized bed or in a stationary bed. In particular, isotropic carbon can be obtained even in a stationary bed if the requirements for the deposition of the isotropic carbon described above are satisfied.     

The interpretation of GLC triglyceride data for the determination of cocoa butter equivalents in chocolate: A new approach

A new approach to interpret triglyceride data obtained by gas liquid chromatography (GLC) in order to determine cocoa butter equivalents (CBE) in chocolate is described. The approach is based on the known straight line relationship which exists between the C₅₀ and C₅₄ triglycerides of cocoa butter of different origins and the realization that, for currently available CBE conforming to CAOBISCO’s criteria, a similar band relationship exists. The technique described enables the quantity of unspecified CBE in a chocolate containing an unknown cocoa butter to be determined to an accuracy of ±1.5% when present in chocolate at the 5% level. Nut oils (almond, walnut or hazelnut) are sometimes present in mainland European chocolates and, should CBE also be present, it is possible to calculate the combined percentages of nut oil and CBE in the chocolate. The method of interpretation described is not dependent on a particular GLC technique for determining triglycerides. Interpretation of other laboratories’ results obtained using different GLC instruments and procedures has shown that the method enables any CBE present in the fat under examination to be determined accurately. The method compensates for variations in the composition of CBE and for the differences between cocoa butters of different origin. A detailed knowledge of CBE compositions is not required and only a few cocoa butter/CBE standards are necessary. The method described is graphical, enabling small laboratories not equipped with microcomputers to utilize the method. The calculation can, however, be programmed for a computer.     

An adaptive genetic algorithm for the time dependent inventory routing problem

In this paper we propose an adaptive genetic algorithm that produces good quality solutions to the time dependent inventory routing problem (TDIRP) in which inventory control and time dependent vehicle routing decisions for a set of retailers are made simultaneously over a specific planning horizon. This work is motivated by the effect of dynamic traffic conditions in an urban context and the resulting inventory and transportation costs. We provide a mixed integer programming formulation for TDIRP. Since finding the optimal solutions for TDIRP is a NP-hard problem, an adaptive genetic algorithm is applied. We develop new genetic representation and design suitable crossover and mutation operators for the improvement phase. We use adaptive genetic operator proposed by Yun and Gen (Fuzzy Optim Decis Mak 2(2):161–175, 2003) for the automatic setting of the genetic parameter values. The comparison of results shows the significance of the designed AGA and demonstrates the capability of reaching solutions within 0.5 % of the optimum on sets of test problems.