Defect levels in chromium-doped silicon

The transient capacitance technique has been used to study the chromium-related levels in the silicon band gap. Chromium was diffused at temperature of 1100 and 1150°C for 0.5 and 3 hr. Five different levels at E_c?0.11 eV, E_c?0.21 eV, E_c?0.28 eV, E_c?0.36 eV and E_c?0.45 eV were obtained from the Arrheniu plots of the electron thermal-emission rates. The number of levels in the upper half of the band gap decreased from five to two with an increase of Cr-diffusion period. Two levels were located at E_c?0.20 eV (donor) and E_c?0.43 eV (acceptor). A donor level was also observed at E_v + 0.25 eV. The donor level was not affected by the diffusion condition. The majority carrier capture cross sections of the three dominant levels have been measured by the transient capacitance technique modified by the pulse transformer. The values were σ_n = 4.1 × 10^?15 cm² for the upper donor at E_c?0.20 eV, σ_n = 2.0 × 10^?16 cm² for the acceptor at E_c ?0.43 eV and σ_p = 9.1 × 10^?18 cm² for the lower donor at E_v + 0.25 eV, and were independent of temperature. The three dominant levels are due to distinct chromium centers.     

Pulsed laser irradiation impact on two marine diatoms Skeletonema costatum and Chaetoceros gracilis

The ability of pulsed laser irradiations to cause damage on the biofouling organisms is recently being investigated. If this technique is employed in industries such as power generation wherein a large quantity of water is being used for the cooling purpose, many organisms other than the targeted would get affected. In this study, we have investigated the damage caused by the pulsed laser irradiations from an Nd:YAG laser (fluence 0.1J/cm(2)) for varying durations such as 2, 5, 10, 30, 60 and 300 s on two marine diatom species namely Skeletonema costatum and Chaetoceros gracilis. Upon exposure to low power laser irradiations, these diatom species showed mortalities between 52.6+/-9.3% to 97.7+/-3.1% in the case of S. costatum and 57.8+/-2.5% to 98.9+/-0.6% in the case of C. gracilis for 2 and 300 s of irradiations, respectively. The mortality increased with the increase in the duration of laser irradiation. The estimation of the chlorophyll a concentration in the irradiated samples showed a considerable reduction varying between 9.8% and 57% in C. gracilis and 3% and 70.3% in S. costatum for 2 and 300 s of irradiations, respectively. The laser-survived cells grew as the non-irradiated (control) samples. C. gracilis frustules were broken by the laser whilst, the cell materials were drained out of the frustules in the case of S. costatum. The study therefore showed that the low power pulsed laser irradiations could cause significant damage on the two species of planktonic diatoms.     

Visualization of Bubble Nucleation in Boiling 3He

The heat transfer properties of ³He bubbles in the nucleate boiling state have been investigated in liquid ³He below 1.0 K by using the shadowgraph method. The temperature difference between the copper surface and liquid ³He temperature was also measured as a function of heat flux in steady state. The size and number of bubbles departing from the surface in a specific time were compared using photograph recorded by a high-speed video camera at various heat flux and liquid ³He temperature of 0.5, 0.7 and 1.0 K.     

Probabilistic output admissible set for systems with time-varying uncertainties

This paper considers time-varying uncertain constrained systems, and develops a method for computing a probabilistic output admissible (POA) set. This set consists of the initial states probabilistically assured to satisfy the constraint. The time-invariant counterpart has already been investigated in Hatanaka and Takaba [Computations of probabilistic output admissible set for uncertain constrained systems, Automatica 44 (2) (2008), to appear]. We first define the POA set for time-varying uncertainties with finite dimensional probability space. Then, we show that an algorithm similar to Hatanaka and Takaba [Computations of probabilistic output admissible set for uncertain constrained systems, Automatica 44 (2) (2008), to appear] provides the POA set also in the time-varying case, as long as an upper bound of a what we call future output admissibility (FOA) index is available. We moreover present two methods for computing the upper bound of the FOA index: probabilistic and deterministic methods. A numerical simulation demonstrates the effectiveness of our algorithm.     

Microstructure and Thermal Shock Resistance of Molten Glass-Coated Carbon Materials Fabricated by Interfacial Control

Carbon substrates were coated completely with a molten silicate glass, where the wettability of carbon to glass was improved by infiltration and pyrolysis of perhydropolysilazane. Microstructures of the carbon–glass interface were dependent on P n ₂ during coating. Coating at lower P n ₂ induced the formation of cristobalite at the carbon–glass interface. When the coating was performed at higher P n ₂, the glass and carbon were strongly adhered, without the formation of cristobalite. Coating at higher P n ₂ improved the thermal shock resistance of the glass layer, because crack initiation was not induced by the phase transformation of cristobalite during the cooling process. In the case of coating at higher P n ₂, an oxynitride glass layer was formed at the glass subsurface by dissolution of N₂. A porous glass subsurface layer with uniform spherical micro-pores could be produced by soaking near the glass transition temperature in a steam environment. The porous layer with fine and homogeneous microstructure acts as a thermal shock absorbing layer, so that glass-coated carbon with a porous glass layer has excellent thermal shock resistance in addition to steam oxidation resistance.     

Carbon Dioxide Sensor Mechanism of Porous Hydroxyapatite Ceramics

Hydroxyapatite and Cl⁻ -containing hydroxyapatite powders are prepared and characterized. Reversible substitution of CO^2-₃ for OH⁻ at the surface is presumed to be responsible for the sensor function. The role of Cl⁻, which is necessary to realize the sensor function and is incorporated during soaking treatment, is considered as follows. It may reduce the strain caused by the incorporation of CO^2-₃ (which is larger than OH⁻), and, hence, promote the reversible substitution reaction. This behavior is presumed because Cl⁻ -containing hydroxyapatite samples exhibit sensor characteristics typical of CO₂ without any treatment.     

Methanogenic digestion using mixed substrate of acetic, propionic and butyric acids

Experiments on methanogenic digestion using high concentrations of mixed substrate were conducted. The major intermediate products of anaerobic digestion such as acetic, propionic and butyric acids were mixed in a ratio of 2:1:1 (COD basis), respectively, and used as a substrate for feeding into continuous-flow chemostat reactors maintained at 35°C. These reactors were operated stably at higher feed substrate concentrations and shorter hydraulic retention times (HRT) than those of using a single component of volatile fatty acids as a substrate. At an HRT of 4.43 days, the methanogenesis occurred normally up to a feed substrate concentration of 70,000 mg COD I⁻¹. At a feed substrate concentration of 20,000 mg COD I⁻¹, the methanogenesis occurred normally up to an HRT of 2.91 days and the minimum SRT for microbial populations was calculated to be 2.42 days. An increase in feed substrate concentration adversely affected the propionate degradation strikingly, while a decrease in HRT significantly adversely affected the acetate and propionate degradation. The methane production was 0.301 g⁻¹ COD utilized, and it was independent of the feed substrate concentration and HRT. Bacilli were predominant in all reactors, but sarcinae appeared in the reactors with high feed substrate concentrations and short HRTs. Phenomena in digester failure due to methanogen washout were also observed.     

Study on chemical structures of poly (tetrafluoroethylene-co-perfluoroalkylvinylether) by soft-EB irradiation in solid and molten state

Poly (tetrafluoroethylene-co-perfluoroalkylvinylether) (PFA) was irradiated by soft electron beam (soft-EB) under nitrogen gas atmosphere in solid-state and its molten state, respectively. The changes of thermal property and chemical structures of irradiated PFA in solid-state and molten state were studied by differential scanning calorimetric analysis (DSC) and solid-state ¹⁹F magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy. By DSC analysis, the melting temperature shifted to lower temperatures, and crystallinity decreased with increasing soft-EB dose. By solid-state ¹⁹F MAS NMR spectroscopy, the new signals was observed and the detected new signals in irradiated PFA at 315 °C and at 30 °C were due to the tertiary carbon group with branching site (Y-type crosslinking site), perfluoro-propylene site and chain end methylene groups, respectively.Moreover, the molar ratio of perfluoroalkylvinylether (FAVE) structure to -CF₂- units decreased with increasing dose.     

MiR-10a in Pancreatic Juice as a Biomarker for Invasive Intraductal Papillary Mucinous Neoplasm by miRNA Sequencing

New biomarkers are needed to further stratify the risk of malignancy in intraductal papillary mucinous neoplasm (IPMN). Although microRNAs (miRNAs) are expected to be stable biomarkers, they can vary owing to a lack of definite internal controls. To identify universal biomarkers for invasive IPMN, we performed miRNA sequencing using tumor-normal paired samples. A total of 19 resected tissues and 13 pancreatic juice samples from 32 IPMN patients were analyzed for miRNA expression by next-generation sequencing with a two-step normalization of miRNA sequence data. The miRNAs involved in IPMN associated with invasive carcinoma were identified from this tissue analysis and further verified with the pancreatic juice samples. From the tumor-normal paired tissue analysis of the expression levels of 2792 miRNAs, 20 upregulated and 17 downregulated miRNAs were identified. In IPMN associated with invasive carcinoma (INV), miR-10a-5p and miR-221-3p were upregulated and miR-148a-3p was downregulated when compared with noninvasive IPMN. When these findings were further validated with pancreatic juice samples, miR-10a-5p was found to be elevated in INV (p = 0.002). Therefore, three differentially expressed miRNAs were identified in tissues with INV, and the expression of miR-10a-5p was also elevated in pancreatic juice samples with INV. MiR-10a-5p is a promising additional biomarker for invasive IPMN.     

A study on the characteristics of glass fibre reinforced thermoplastics by transfer moulding

Lately, the use of fibre reinforced thermoplastics (FRTP) has increased due to its increased mouldability compared to thermosetting FRP material.

FRTP includes stampable sheet, short and long fibre reinforced thermoplastic pellets, continuous fibre reinforced thermoplastics sheets, etc. The long fibre reinforced thermoplastic (LFRTP) pellet has better mechanical properties than short fibre reinforced pellets and better mouldability than stampable sheet. At present, injection moulding method is mainly used for moulding LFRTP pellets because of its high productivity.

However, the long fibre of LFRTP pellets, whose length is the same as pellet length, is degraded during processing if conventional injection moulding machines are used, and as a result, the mechanical properties are not improved as expected in many cases. Therefore, a new moulding process is required to make good use of LFRTP pellets.

For this study, a transfer moulding apparatus was designed and built to minimize fibre degradation of the moulded parts.

Firstly, the LFRTP pellets with fibre lengths of 3, 6, 9, 12.7 and 17 mm were prepared in order to clarify the difference of mechanical properties due to fibre length. The fibre ratio was 30% in weight for all cases and the same polypropylene was used. They were moulded to the shape of the test specimens. Tensile, bending and Izod impact strengths were measured by using these test specimens. Secondly, LFRTP pellets were moulded to the shape of test specimens by the transfer moulding apparatus and conventional injection moulding machine, and then mechanical properties were measured. At the same time, short fibre pellets were moulded to the smae shape of test specimens by the injection moulding machine, and mechanical properties were compared with those of LFRTP pellets.

With the long glass fibre reinforced polypropylene, good results of fibre preservation and mechanical properties were obtained by the transfer moulding apparatus which was built for this study. The impact strength was increased remarkably as the fibre length increased, and consequently the preservation of fibre length in the moulded parts was especially effective in improving the impact strength.