Research and development of liquid hydrogen (LH2) temperature monitoring system for marine applications

Monitoring the temperature in liquid hydrogen (LH₂) storage tanks on ships is important for the safety of maritime navigation. In addition, accurate temperature measurement is also required for commercial transactions. Temperature and pressure define the density of liquid hydrogen, which is directly linked to trading interests. In this study, we developed and tested a liquid hydrogen temperature monitoring system that uses platinum resistance sensors with a nominal electrical resistance of approximately 1000 Ω at room temperature, PT-1000, for marine applications. The temperature measurements were carried out using a newly developed temperature monitoring system under different pressure conditions. The measured values are compared with a calibrated reference PT-1000 resistance thermometer. We confirm a measurement accuracy of ±50 mK in a pressure range of 0.1 MPa–0.5 MPa.     

Oxidation of doped europium in BaMgAl10O17 by annealing studied by x‐ray‐absorption fine‐structure measurements

Abstract— We studied the influence of annealing in air on doped europium in BaMgAl₁₀O₁₇ by performing x‐ray absorption fine‐structure measurements. We determined the oxidation of doped divalent europium by annealing in air at over 500°C. The interatomic distance between the europium and the surrounding oxygen atoms was compressed by oxidation. It also appears that the oxidation process of europium is determined by the diffusion of oxygen into BaMgAl₁₀O₁₇.     

A flow simulation for the epoxy casting process using a 3D finite‐element method

A three‐dimensional flow simulation for epoxy casting has been developed. A control‐volume‐based finite‐element method is employed, containing a conservative upwind formulation for the advection terms and equal order interpolations for all variables. This simulation predicts the non‐isothermal and reactive flow behavior under the gravity. The viscosity and reaction‐rate parameters were estimated by using a dynamic rheometer and a differential scanning calorimeter. The predicted flow front advancement and temperature profiles in the calculation domain similar to the mold cavity were in close agreement with the corresponding experimental results. The variation of epoxy surface configuration with flow rate also showed the same tendency between the prediction and the experiment. This simulation seems to be applicable not only to the epoxy casting, but also to other molding processes of various thermoset resins. POLYM. ENG. SCI. 45:364–374, 2005. © 2005 Society of Plastics Engineers.     

The levels of integrin alpha v beta 5 may predict the susceptibility to adenovirus-mediated gene transfer in human lung cancer cells

Adenovirus mediated transfer of growth-inhibiting molecules, such as p53 shows promise as an effective method of suppressing the growth of cancer cells. As the basis for in vivo studies, we examined transfection efficiency using 15 human lung cancer cell lines that differ in their endogenous p53 status. When infected with an adenovirus expressing bacterial beta-galactosidase, the different cell lines showed different levels of beta-galactosidase activity. We found a correlation between the level of integrin alpha v beta 5, which is thought to be an adherence receptor for adenoviruses, and the expression level of the transferred gene, suggesting that gene expression is largely dependent on the infection efficiency. Growth inhibition was induced in all cell lines tested following infection with an adenovirus containing p53, regardless of the genetic status of their endogenous p53 provided a sufficient amount of p53 protein was expressed. Our results (1) confirm that the examination of the susceptibility of target cancer cells to an adenovirus is important when considering performing adenovirus-mediated gene transfer and for evaluating its therapeutic effects; and (2) suggest that the quantification of integrin alpha v beta 5 may be a good way of predicting the susceptibility of cells to adenoviral vectors.     

Impaired stereoacuity due to a lesion in the left pulvinar

A right-handed patient with a haematoma in the left pulvinar showed impaired stereoacuity. In contrast with previous reports, he did not show peripheral visual extinction or prolonged reaction times for targets on the side contralateral to the lesion.     

Two geometrical isomers of linoleic acid: Improved total syntheses

The total syntheses of 9(Z),12(E)- and 9(E),12(Z)-octadecadienoic acids have been carried out. A useful intermediate in both syntheses, 8-bromo-octanoic acid, recently has become available from commercial sources. This compound has been used to expedite the preparation of these isomers. The remaining carbon atoms were derived from propargyl alcohol along with either 1-heptyne or acetylene and 1-bromopentane. Because the overall yield for each sequence was roughly 15% and there were no extraordinary reaction conditions in any of the synthetic steps, the compounds could be prepared readily in multiple gram quantities. The syntheses of the two compounds were supported by data from a variety of spectroscopic techniques.     

Distribution of higher-order structures in injection-molded polypropylenes

Flexural test specimens were injection-molded from six homoisotactic polypropylenes with MFI = 0.49-25.1 dg/min under cylinder temperatures of 200-320°C. Distributions in the flow direction of higher-order structures such as crystallinity X_c, thickness of skin layer, a*-axis-oriented component fraction [A*], and crystalline orientation functions and distributions in the thickness direction of higher-order structures such as X_c, β-crystal contents, [A*], and crystalline orientation functions were studied. These higher-order structures are inhomogeneous in the flow and thickness directions, which strongly influences the product properties such as mechanical and thermal properties. Molecular orientation process in injection molding was theoretically analyzed from a viewpoint of growth of recoverable shear strain at the gate and its relaxation in the cavity, which could considerably well explain the variations in the flow and thickness directions of the quantities such as thickness of the skin layer and crystalline orientation functions which express the degree of molecular orientation.     

Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.     

66/77-kV C-GIS using composite insulation in SF6 gas

A second-generation model of cubicletype gas-insulated switchgear (C-GIS) with composite insulation incorporating SF₆ gas has been developed. The design does not require a gas process in field assembly; it has high reliability and its installation is more rapid; and a further reduction in size is achieved. The design principles are described in detail.