Analysis of volatiles evolved during high-temperature treatment of thermally stable polymers. I. Nitrogen-containing acetylene-terminated resin

Cured samples of a nitrogen-containing acetylene-terminated resin, N,N′-(1,3-phenylene-dimethylidene)bis(3-ethynylaniline), have been heated at 10°C/min up to 900°C in a pyroprobe attached to a gas chromatograph/mass spectrometer (GC/MS). Analysis of the volatiles evolved during heating identified both gases and higher boiling compounds. The major higher boiling compounds are benzene, toluene, xylene, aniline, benzonitrile, m-methylaniline, and m-methylbenzonitrile; the gases include ammonia, methane, and traces of carbon dioxide. Correlations between sample temperature and the evolution of each of these compounds have been made. The onset of all volatile formation occurs between 450 and 500°C. The higher boiling volatiles peak, then end by approximately 700°C, while the gases peak then fall off but are still being evolved at 900°C. Average weight loss measurements of 13.6% at 700°C and 15.7% at 900°C agree with previously published thermogravimetric analysis (TGA) data. © 1993 John Wiley & Sons, Inc.     

Use of weibull statistics to quantify property variability in TiAl alloys

Tensile experiments have been performed on specimens of four different investment-cast TiAl-based alloys with variations in casting conditions. The average ductilities obtained in these experiments vary between approximately 0.8 to 2.0 pct plastic strain to failure in tension. By using the three-parameter form of the Weibull relation, with the 0.2 pct offset yield strength as the minimum failure strength, the resulting variability in the data can be quantified and is found to be similar for those alloys with similar microstructural scale (grain size). Large variations in lamellar volume fraction, segregation, and phase distribution have a minor influence on property variability, compared to changes in the scale of the grain structure caused by either variations in cooling rate during casting or the addition of grain refiners.     

Building Bridges to Material Properties in General Chemistry Laboratories: A Model for Integration Across Disciplines

Many engineering students enter and exit general chemistry courses with little appreciation of chemistry's relevance to other fields. At WPI many of these students go on to take introductory materials science and arrive with poor attitudes about chemistry and little retention of key concepts, but then become more engaged as they discover connections to engineering applications. Consequently, instructors in chemistry and mechanical engineering collaborated to augment general chemistry laboratories with explicit “bridges” to material properties and applications. Evaluation results showed that while students' attitudes toward chemistry were unaffected by bridging, particular aspects of the students' lab experience were enhanced to a statistically significant degree. Similar cross‐disciplinary collaborations might be considered elsewhere as a means of helping students find meaning and integrate subject matter, in a manner that is more feasible than large‐scale course or curriculum restructuring.     

Optimized hydrogen positions for aluminium and iron containing hydroxide minerals

The structures of a number of hydroxide and oxyhydroxide minerals have previously been reported without the hydrogen positions explicitly defined. Here we use two atomic scale computer simulation techniques, one based on classical ionic potentials, the other on density functional theory (DFT), to predict these positions. The aim is not only to provide data that can be used as the basis for future experimental structure optimizations but also model parameters that can be used to predict complex hydroxide structures. The efficacy of the approach is demonstrated through the comparison of predicted and experimental data for minerals whose hydrogen positions are known.     

Termites live in a material world: exploration of their ability to differentiate between food sources.

Drywood termites are able to assess wood size using vibratory signals, although the exact mechanism behind this assessment ability is not known. Important vibratory characteristics such as the modal frequencies of a wooden block depend on its geometry and boundary conditions; however, they are also dependent on the material characteristics of the block, such as mass, density and internal damping. We report here on choice experiments that tested the ability of the drywood termite Cryptotermes secundus to assess wooden block size using a solid wooden block paired with a composite block, the latter made of either wood and aluminium or wood and rubber. Each composite block was constructed to match mass or low-frequency vibratory modes (i.e. fundamental frequency) of the solid wooden block. The termites always chose the blocks with more wood; they moved to the solid wooden blocks usually within a day and then tunnelled further into the solid wooden block by the end of the experiment. Termites offered composite blocks of wood and rubber matched for mass were the slowest to show a preference for the solid wooden block and this preference was the least definitive of any treatment, which indicated that mass and/or damping may play a role in food assessment. This result clearly shows that the termites were not fooled by composite blocks matched for mass or frequency, which implies that they probably employ more than a single simple measure in their food assessment strategy. This implies a degree of sophistication in their ability to assess their environment hitherto unknown. The potential importance of alternative features in the vibrational signals is discussed.     

A behavioral medicine intervention in persons with HIV

This study used a pretest-posttest preexperimental design to examine the effect of a 10-week behavioral medicine support group intervention in a sample of persons with HIV. Using Solomon's psychoneuroimmunologic framework, the 10-week behavioral medicine program focused on the mind/body interaction, the relaxation response, coping with illness, hardiness, and nutrition. Pearson correlation coefficients and t tests were performed on the pre- and postintervention measures of hardiness, social support, immune function, and perceived health status. Results of the study indicated that hardiness (preintervention) and CD4 counts (pre- and postintervention) were significantly correlated with health status; however, CD4 counts decreased over the course of the behavioral medicine program. Implications for nursing and recommendations for further research are discussed.     

Directly Compressible Acetaminophen Compositions Prepared by Fluidized-Bed Granulation

Polyvinylpyrrolidone (PVP) in aqueous solution was used as a binding agent in a fluidized-bed system to agglomerate acetaminophen powder into directly compressible granules. It was found that a minimal amount of 5% w/w PVP in a concentration of 7.5% w/v or less was needed to produce granules with an acceptable flow and the corresponding tablets having enough hardness without capping. There was a strong correlation between the time for 80% dissolved (T₈₀) and the logarithm of granule volume-surface mean diameter. A directly compressible acetaminophen composition to manufacture tablets having a T₈₀ value less than 30 min can be prepared simply by adding an appropriate amount of disintegrant (crospovidone, sodium starch glycolate, or pregelatinized starch) to the agglomerated granules.     

A new efficient dcvs circuit synthesis technique used for an improved implementation of a serial/parallel multiplier

This paper describes an efficient technique for the design of fault-secure VLSI circuits based on differential cascode voltage switch (DCVS) logic. We propose a new synthesis method for constructing DCVS circuits with a near-optimal transistor count based on binary decision diagrams (BDDs). the time and memory resources required are very low, making the technique practical even for PC-based synthesis tools. This method is the basis for a CAD tool that allows automatic synthesis of fault-secure circuits based on the DCVS technology. We finally present an improved design and implementation of a 2's complement serial/parallel multiplier as an application of the proposed technique and algorithm.