Cooling of cylindrical vertical tanks submitted to natural internal convection

A numerical and an experimental analysis of velocity and temperature fields inside a storage tank submitted to natural convection is presented. The analysis was performed in two stages. In the first stage, the temperature profile along the vertical axis of the storage tank was obtained experimentally and numerically, for cooling time ranging from 45 to 60 h. The numerical analysis was carried out using a transient bi-dimensional model in cylindrical co-ordinates. In the second stage, after the numerical code validation, 40 cases of cooling with four aspect ratios, five insulation thicknesses, and two different volumes were simulated. In all simulations, thermal losses for the environment in all tank walls (side, top and bottom) were considered. Two correlations for the Nusselt number, encompassing all the forty cases, were obtained with these results.     

Stability studies on methyl and ethyl fatty acid esters of sunflowerseed oil

Fatty acid esters, high in linoleic acid, were prepared and stored for long-term engine tests. Storage tests with these esters were undertaken to obtain more information on optimal storage requirements and general stability characteristics. Samples were kept at three temperature levels (20 C, 30 C and fluctuating around 50 C) for a 90-day period and were removed at regular intervals for chemical and physical analysis. The influence of air, temperature, light, TBHQ and contact with mild steel was evaluated by comparing the free fatty acid, peroxide, anisidine, ultraviolet absorption, viscosity and induction periods. A statistical model was used to evaluate the data and to reduce the large number of data points to comparable curves. Storage of esters in contact with air, especially at a temperature above 30 C, resulted in significant increases in peroxide, ultraviolet absorption, free fatty acid, viscosity and anisidine values. Exclusion of air retarded oxidation at all temperature levels. A direct relationship between viscosity increases and oxidation parameters was evident. Exposure to light caused a small increase in the oxidation parameters of esters stored at the highest temperature level. Addition of TBHQ prevented oxidation of samples stored under moderate conditions. Under unfavorable storage conditions the anti-oxidant was no longer effective. Mild steel had very little effect on the oxidation parameters. Only the anisidine values of samples stored at the highest temperature level were slightly increased. Methyl esters performed slightly better than ethyl esters during the storage test. The following practical guidelines for storage of fatty acid ester fuels are: (i) airtight containers should be used; (ii) the storage temperature should be <30 C; (iii) mild steel (rust free) containers may be used, and (iv) TBHQ has a beneficial effect on oxidation stability.     

Meßtechnik zur Charakterisierung von Gas/Flüssigkeits-Reaktoren

Measuring techniques for characterizing gas/liquid reactors . The article considers measuring techniques for the characterization of the phases in gas/liquid reactors. These include the velocity profile and turbulence in the continuous phase as well as holdup, size, and velocity of the dispersed phase. Also, methods for the determination of the specific interfacial area and the volumetric mass transfer coefficients are discussed. Measuring methods have made enormous advances in recent years. In spite of this, there is a lack of reliable methods, especially for use during reactions without disturbing the state of the reactor. It is suspected that probe technique will gradually fall into disuse and more and more attention will be focussed on contractless methods. This calls for further development of ultrasonic methods and methods relying on emission of light.     

Optimised electromagnetic 3d field solver for frequencies below the first resonance

An optimised low-frequency solution algorithm is proposed that reduces the electromagnetic wave equation to a small number of scalar potential problems. The latter can be solved using black-box algebraic multigrid solvers. Within the framework of the finite integration technique, the reduction of the wave equation is accomplished by tree/cotree decompositions of primary and dual grids, which allow for highly efficient solutions of Ampere's and Faraday's equations. The example of a ferrite-loaded accelerator component demonstrates that the scheme is much more efficient than the direct approach using Krylov subspace solvers     

Structural Appraisal of the Florentine Gothic Construction System

The nave of Santa Maria Novella, a Dominican church in Florence Italy is representative of a Florentine Gothic system of construction. This system, consisting of domical rib vaults on square nave bays, high side aisles, and crypto-buttressing, differs substantially from the French high Gothic system of even-level-crown rib vaults on rectangular bays, with flying buttresses over relatively low aisles. An investigation into the structural aspects of the Florentine Gothic construction system reveals that the domical vaults increase the longitudinal thrust and reduce the transverse thrust, which may require additional precautions to be taken during construction, but entails a less elaborate buttressing system. The domical vaults are found to perform well structurally, with an absence of tensile stresses, and are more suitable for a square bay. In general, the structural system of the nave of Santa Maria Novella is found to be the product of carefully considered structural design, which may be accepted as an alternative to the French Gothic construction system.     

Contractor Prebid Planning Principles

Planning is an essential function of project management. Yet, many small- and medium-sized contractors do a relatively poor job of operational planning. Better prebid plans will reduce costs, shorten schedules, and improve labor productivity. Unfortunately, the published literature offers little guidance for smaller contractors on what constitutes effective planning. Most papers describe planning as a macrolevel process for owners. Most emphasize scope definition for industrial projects. This paper describes a microlevel planning process for contractors. It consists of eight steps which are: (1) assess contract risks; (2) develop a preliminary execution plan; (3) develop site layout plans; (4) identify the sequences that are essential-to-success; (5) develop detailed operational plans; (6) develop proactive strategies to assure construction input into design; (7) revise the preliminary plan; and (8) communicate and enforce the plan. The entire process is illustrated with a case study project and is fully illustrated with figures which show how to integrate the work of multiple contractors, keep key resources (crews or equipment) fully engaged with no downtime, provide time buffers so the work of follow on crews can be efficiently done, expedite the schedule using multiple work stations and concurrent work, ways to communicate the work plan to the superintendent and foremen, and how to assess the feasibility of various work methods. The steps are easy to understand and implement. They will yield immediate positive results.     

History of Construction, Engineering, and Management in the Department of Civil and Environmental Engineering at Penn State

At Penn State, the credit for broadening the Civil Engineering Department’s longstanding academic focus on analysis and design to include the construction phase must go to Dr. Harmer A. Weeden and his longtime associate Dr. Thomas D. Larson. Jack H. Willenbrock joined the Department as an Instructor in June 1968 and grew the construction program so that today about a fourth to a third of the civil undergraduates obtain employment in the construction industry. The program has awarded about 250 postbaccalaureate degrees.     

Dynamic Complexity Theory Revisited

Dynamic complexity investigates the required effort to maintain knowledge about a property of a structure under changing operations. This article introduces a refined notion of dynamic problems which takes the initial structure into account. It develops the basic structural complexity notions accordingly. It also shows that the dynamic version of the LOGCFL-complete problem D₂LREACH(acyclic) can be maintained with first-order updates.