悬浮床加氢裂化油溶性催化剂与沥青质的作用

在高压釜反应器中对添加了油溶性 Ni 催化剂(UPC-O)和水溶性 Ni 催化剂(UPC-W)的辽河稠油常压渣油(LHAR)进行了悬浮床加氢裂化实验。通过元素分析和傅里叶变换红外光谱(FTIR)分析对抑制反应生焦效果好的 UPC-O 与 LHAR 沥青质的作用进行了研究。元素分析结果显示,在 LHAR 中加入 UPC-O1000μg/g,沥青质和脱沥青质油中 Ni 含量分别出476μg/g和110μg/g 增加到7 559μg/g 和1 024μg/g,表明 UPC-O 在沥青质中有富集的趋势。FTIR 表征结果显示,UPC-O 和沥青质发生了相互作用。UPC-O 可在沥青质原位硫化为活性组分,对沥青质在悬浮床加氢裂化反应中的缩合起到好的抑制作用。     

添加剂强化重油催化裂化的过程分析与应用

运用工程化学原理分析讨论了添加剂强化重油催化裂化的过程，包括分散稳定气泡、改善雾化、保护酸中心、抑制焦炭生成以及提高重油气化率的胶体结构改性、降低表面张力和改善微孔润湿，并用以指导强化重油催化裂化添加剂的筛选。建立小型固定流化床催化裂化实验装置评价了添加剂的强化效果。结果表明，添加剂强化重油催化裂化可降低催化剂生焦1．0％左右，提高总液体收率1．0％～2．8％。     

一种简易的手工网印序号工艺法

通过一种简易的手工丝印序号工艺法,可以连续完成逐张PCB的序号印制且质量稳定。     

Q195冷轧板材轧制困难原因分析

针对部分Q195冷轧板材存在轧制困难的现象，进行了现场检验与分析。带状组织、混晶现象严重导致变形强化系数偏高是造成轧制困难的主要原因。     

导向剂加入方式对Y型沸石合成的影响

以煤系高岭土为原料,采用液态补硅手段调节体系SiO2/Al2O3、导向剂两步加入法合成了Y型沸石.考察了导向剂不同加入方式对Y型沸石合成的影响.采用合理的导向剂两步加入法,特别是通过控制导向剂第二步加入的时间,可明显缩短Y型沸石的晶化时间,并有效地减少P型沸石的生成.     

The quantification of remote sensing

The paper firstly defined the remote sensing information quantification, analyzed the necessity of developing remote sensing quantification, figured out the application guidelines requirement, and pointed out the importance of quantification research. Then taking the remote sensing application research of CBERS-02 data quantification as the example, the paper described the whole quantification system of “remotely sensed digital signal-radiation information-field parameter inversion”. Finally the paper gave the prospect for the development trend of the quantitative remote sensing.     

S28-248型偏心BDC钻头的研制与应用

为了提高中原油田沙3中至沙4段四开小井眼的钻井速度,有效地解决易卡钻、钻速低、成本高以及小间隙井眼固井质量差等问题,中原油田与川石·克里斯坦森金刚石钻头有限公司合作,研制开发了用于深部小井眼钻井的149.2mm的S28-248型偏心BDC钻头。详细介绍了该钻头的设计特点及现场应用情况。     

自制小型铺轨机具铺设隧道宽枕轨道

结合宝成复线新大滩隧道铺设J-82型预应力混凝土宽轨枕板采用的施工技术，就其机具的组成功用及施工方法作了介绍，指出了KPZ-50型铺轨机具的优点。     

劣化环丁砜再生技术的工业应用

为解决国内外环丁砜抽提芳烃工艺中环丁砜的劣化问题，在不添加单乙醇胺的前提下，采用阴离子交换树脂处理劣化的环丁砜，可使系统的pH值从3．4升到5．5左右，离子交换树脂需30d左右再生一次，降低了设备的腐蚀，减少了装置的堵塞，使系统运行稳定，取得了可观的社会效益和经济效益。     

Microfabricated preconcentrator-focuser for a microscale gas chromatograph

The design, fabrication, and testing of a preconcentrator-focuser (PCF), consisting of a thick micromachined Si heater packed with a small quantity of a granular adsorbent material are described. The PCF is developed to capture and concentrate vapors for subsequent focused thermal desorption and analysis in a micro gas chromatograph. The microheater contains an array of high-aspect-ratio, etched-Si heating elements, 520 /spl mu/m (h)/spl times/50 /spl mu/m (w)/spl times/3000 /spl mu/m (l), bounded by an annulus of Si and thermally isolated from the remaining substrate by an air gap. This structure is sandwiched between Pyrex glass plates with inlet/outlet ports that accept capillary tubes for sample flow and is sealed by anodic bonding (bottom) and rapidly annealed glass/metal/Si solder bonding (top). The large microheater surface area allows for high adsorption capacity and efficient, uniform thermal desorption of vapors captured on the adsorbent within the structure. The adsorbent consists of roughly spherical granules, /spl sim/200 /spl mu/m in diameter, of a high-surface-area, graphitized carbon. Key design considerations, fabrication technologies, and results of performance tests are presented with an emphasis on the thermal desorption characteristics of several representative volatile organic compounds as a function of volumetric flow rates and heating rates. Preconcentration factors as high as 5600 and desorbed peak widths as narrow as 0.8 s are achieved from 0.25-L samples of benzene at modest heating rates. The effects of operating variables on sensitivity, chromatographic resolution, and detection limits are assessed. Testing of this PCF with a micromachined separation column and integrated sensor array is discussed briefly.