Present Status of the Nd:YAG Thomson Scattering System Development for Time Evolution Measurement of Plasma Profile on Heliotron J

A new high repetition rate Nd:YAG Thomson scattering system is developed for the Heliotron J helical device.A main purpose of installing the new system is the temporal evolution measurement of a plasma profile for improved confinement physics such as the edge transport barrier (H-mode) or the internal transport barrier of the helical plasma.The system has 25 spatial points with ～10mm resolution.Two high repetition Nd:YAG lasers (>550mJ@ 50Hz) realize the measurement of the time evolution of the plasma profile with ～10ms time intervals.Scattered light is collected by a large concave mirror (D=800 mm,f/2.25) with a solid angle of ～100 mstr and transferred to interference filter polychromators by optical fiber bundles in a staircase form.The signal is amplified by newly designed fast preamplifiers with DC and AC output,which reduces the low frequency background noise.The signals are digitized with a multi-event QDC,fast gated integrators.The data acquisition is performed by a VME-based system operated by the CINOS.     

Effect of Ultrasonication on the Microstructure and Tensile Elongation of Zirconia-Dispersed Alumina Ceramics Prepared by Colloidal Processing

To obtain dense, fine-grained ceramics, fine particles and advanced powder processing, such as colloidal processing, are needed. Al₂O₃ and ZrO₂ particles are dispersed in colloidal suspensions by electrosteric repulsion because of polyelectrolyte absorbed on their surfaces. However, additional redispersion treatment such as ultrasonication is required to obtain dispersed suspensions because fine particles tend to agglomerate. The results demonstrate that ultrasonication is effective in improving particle dispersion in suspensions and producing a homogeneous fine microstructure of sintered materials. Superplastic tensile ductility is improved by ultrasonication in preparing suspensions because of the dense and homogeneous fine microstructure.     

Effect of sintering additive on crystallographic orientation in AlN prepared by slip casting in a strong magnetic field

The preparation of oriented AlN bulk ceramics with and without additives was achieved by slip casting in a high magnetic field. The a and b axes of the AlN were aligned parallel to the direction of the magnetic field. The degree of crystallographic orientation was controlled by the viscosity of the slurry and the grain growth during sintering attributed to the sintering additives. The mechanical properties of the textured AlN depended on the direction of the crystallographic orientation.     

Switched capacitor circuit for 1/f noise generation using a power-law circuit

A simple switched capacitor (SC) circuit is given which realizes a one-dimensional discrete dynamical system X_n+1 = X_n + ux^z generating intermittent chaos with a 1/f-shaped power spectrum. an integrated circuit with a pair of logarithmic and antilogarithmic amplifiters can easily realize the power-law term x^z which plays a key role in generating l/fnoise. an inevitable small offset voltage ? in the SC circuit governs the cut-off frequency of 1/f noise, and when the dynamical system is modified by introducing an effective ?, the ‘indirect method’ enables us to get the precise power spectrum in the modified system.     

Interactive segmentation of the cerebral lobes with fuzzy inference in 3T MR images.

Measurement of volume and surface area of the frontal, parietal, temporal and occipital lobes from magnetic resonance (MR) images shows promise as a method for use in diagnosis of dementia. This article presents a novel computer-aided system for automatically segmenting the cerebral lobes from 3T human brain MR images. Until now, the anatomical definition of cerebral lobes on the cerebral cortex is somewhat vague for use in automatic delineation of boundary lines, and there is no definition of cerebral lobes in the interior of the cerebrum. Therefore, we have developed a new method for defining cerebral lobes on the cerebral cortex and in the interior of the cerebrum. The proposed method determines the boundaries between the lobes by deforming initial surfaces. The initial surfaces are automatically determined based on user-given landmarks. They are smoothed and deformed so that the deforming boundaries run along the hourglass portion of the three-dimensional shape of the cerebrum with fuzzy rule-based active contour and surface models. The cerebrum is divided into the cerebral lobes according to the boundaries determined using this method. The reproducibility of our system with a given subject was assessed by examining the variability of volume and surface area in three healthy subjects, with measurements performed by three beginners and one expert user. The experimental results show that our system segments the cerebral lobes with high reproducibility.     

Theory of powdered metal formation in electrochemistry—morphological instability in galvanostatic crystal growth under diffusion control

Following the presentation of the theory of powder formation in steady state electrocrystallization, some equations based on the linear instability theory in non-steady state deposition under diffusion control were derived; the galvanostatic case was then analysed using the theoretical equations obtained here.As a result, the dependences of powder growth and particle size on various physical parameters, such as current density, bulk concentration and temperature, were made quantitatively clear. Furthermore, a reliable basis was given to the induction time of powder formation which had formerly been liable to amibiguous discussion.     

Distribution of ytterbium (Yb) in cells of Streptomyces sp. YB-1 which can accumulate Yb, and reusability of cells and cell membrane as bioadsorbent for Yb

The cells of Streptomyces sp. YB-1 adsorbed 4-6 mg ytterbium (Yb) per g dry weight. The Yb contents of the cell wall fraction, cell-free extract, and cell membrane fraction were 11%, 2%, and 87%, respectively. The Yb content in the cell membrane fraction was 20-25 mg per g dry weight. The adsorbed Yb could be quantitatively desorbed by treating the cell membrane fraction with 1 mM EDTA and 1 M HCl at 37 degrees C for 4 h. Treatment with 1 M NaOH caused Yb desorption to some extent. Treatments with proteinase K, lysozyme, 0.5% Triton X-100, 0.4% sodium dodecyl sulfate, and 1 M NaCl did not cause Yb desorption. Elemental analysis of Yb-adsorbed materials after removal of proteins and then extraction of lipids from the membrane fraction revealed that the molar ratio of Yb and P in the materials was about 1:1. The cells and the membrane fraction could be used repeatedly as a bioadsorbent for Yb.     

Evaluation of TEM samples of an Mg-Al alloy prepared using FIB milling at the operating voltages of 10 kV and 40 kV

Transmission electron microscopy (TEM) samples of an Mg-Al alloy has been prepared using a Ga-focused ion beam (FIB) milling at two different operating voltages of 10 kV and 40 kV to investigate the influence of the FIB energy on the sample quality. The fine structures of the samples have been studied using a high resolution TEM, and the concentration of the implanted Ga was analysed using an energy dispersive X-ray (EDX) analysis. The result of the TEM observation revealed that point defects were introduced to the sample finally milled at 40 kV but not at 10 kV. However, crystal lattice images and electron diffraction patterns were clearly observed on both the samples. The typical influence of the FIB energy was indicated in the elemental analysis. The relative Ga concentration in the thin sample finally milled at 10 kV was 1.0-2.0 at% that is less than half of 4.0-6.0 at% of the Ga concentration in the sample finally milled at 40 kV. A comparison between the experimental results of the Ga concentration measurement with simulation was also discussed.     

Simple and comprehensive two-dimensional reversed-phase HPLC using monolithic silica columns

Simple and comprehensive two-dimensional (2D)-HPLC was studied in a reversed-phase mode using monolithic silica columns for second-dimension (2nd-D) separation. Every fraction from the first column, 15 cm long (4.6-mm i.d.), packed with fluoroalkylsilyl-bonded (FR) silica particles, was subjected to the separation in the 2nd-D using one or two octadecylsilylated (C(18)) monolithic silica columns (4.6-mm i.d., 3 cm). Monolithic silica columns in the 2nd-D were eluted at a flow rate of up to 10 mL/min with separation time of 30 s that meets the fractionation every 15-30 s at the first dimension (1st-D) operated at a flow rate of 0.4-0.8 mL/min. Three cases were studied. (1) In the simplest scheme of 2D-HPLC, effluent of the 1st-D was directly loaded into an injector loop of 2nd-D HPLC for 28 s, and 2 s was allowed for injection. (2) Two six-port valves each having a sample loop were used to hold the effluent of the 1st-D alternately for 30 s for one 2nd-D column to effect comprehensive 2D-HPLC without the loss of 1st-D effluent. (3) Two monolithic silica columns were used for 2nd-D by using a switching valve and two sets of 2nd-D chromatographs separating each fraction of the 1st-D effluent with the two 2nd-D columns alternately. In this case, two columns of the same stationary phase (C(18)) or different phases, C(18) and (pentabromobenzyloxy)propylsilyl-bonded (PBB), could be employed at the 2nd-D, although the latter needed two complementary runs. The systems produced peak capacity of approximately 1000 in approximately 60 min in cases 1 and 2 and in approximately 30 min in case 3. The three stationary phases, FR, C(18), and PBB, showed widely different selectivity from each other, making 2D separations possible. The simple and comprehensive 2D-HPLC utilizes the stability and high efficiency at high linear velocities of monolithic silica columns.     

Purification and characterization of an extracellular beta-agarase from Bacillus sp. MK03

A new beta-agarase was purified from an agarolytic bacterium, Bacillus sp. MK03. The enzyme was purified 129-fold from the culture supernatant by ammonium sulfate precipitation, anion exchange and gel filtration column chromatographic methods. The purified enzyme appeared as a single band on sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). Estimation of the molecular mass by SDS-PAGE and gel filtration gave values of 92 kDa and 113 kDa, respectively. The N-terminal amino acid sequence of the enzyme showed no homology to those of other known agarases. The optimum pH and temperature for this enzyme were 7.6 and 40 degrees C, respectively. The predominant hydrolysis product of agarose by this enzyme was neoagarotetraose, indicating the cleavage of beta-1,4 linkage. This enzyme could hydrolyze neoagarohexaose to produce neoagarotetraose and neoagarobiose; it could not hydrolyze these products. The enzyme digested agarose by endo-type hydrolysis.