Interfacial Phenomena in Al/Al,Al/Cu,and Cu/Cu Joints Soldered Using an Al-Zn Alloy with Ag or Cu Additions

The studies of soldered joints were carried out in systems: Al/solder/Al, Al/solder/Cu, Cu/solder/Cu, where the solder was (Al-Zn)_EUT, (Al-Zn)_EUT with 0.5, 1.0, and 1.5 at.% of Ag and (Al-Zn)_EUT with 0.5, 1.0, and 1.5 at.% of Cu addition. Brazing was performed at 500 °C for 3 min. The EDS analysis indicated that the composition of the layers starting from the Cu pad was CuZn, Cu5Zn8, and CuZn4, respectively. Wetting tests were performed at 500 °C for 3, 8, 15, and 30 min, respectively. Thickness of the layers and their kinetics of growth were measured based on the SEM micrographs. The formation of interlayers was not observed from the side of Al pads. On the contrary, dissolution of the Al substrate and migration of Al-rich particles into the bulk of the solder were observed.     

Proteomic Analysis of Embryogenesis and the Acquisition of Seed Dormancy in Norway Maple (Acer platanoides L.)

The proteome of zygotic embryos of Acer platanoides L. was analyzed via high-resolution 2D-SDS-PAGE and MS/MS in order to: (1) identify significant physiological processes associated with embryo development; and (2) identify changes in the proteome of the embryo associated with the acquisition of seed dormancy. Seventeen spots were identified as associated with morphogenesis at 10 to 13 weeks after flowering (WAF). Thirty-three spots were associated with maturation of the embryo at 14 to 22 WAF. The greatest changes in protein abundance occurred at 22 WAF, when seeds become fully mature. Overall, the stage of morphogenesis was characterized by changes in the abundance of proteins (tubulins and actin) associated with the growth and development of the embryo. Enzymes related to energy supply were especially elevated, most likely due to the energy demand associated with rapid growth and cell division. The stage of maturation is crucial to the establishment of seed dormancy and is associated with a higher abundance of proteins involved in genetic information processing, energy and carbon metabolism and cellular and antioxidant processes. Results indicated that a glycine-rich RNA-binding protein and proteasome proteins may be directly involved in dormancy acquisition control, and future studies are warranted to verify this association.     

Thermal Expansion,Electrical Resistivity,and Spreading Area of Sn-Zn-In Alloys

Thermal expansion and electrical resistivity of alloys based on Sn-Zn eutectic with 0.5, 1.0, 1.5, and 4.0 wt.% additions of In were studied. Thermal expansion measurements were performed using thermomechanical analysis tester over 223-373 K temperature range. Electrical resistivity measurements were performed with four-probe method over 298-423 K temperature range. The electrical resistivity of alloys increases linearly with temperature and concentration of In; also coefficient of thermal expansion of the studied alloys increases with In concentration. Scanning electron microscopy revealed simple eutectic microstructure with In dissolved in Sn-rich matrix. The results obtained were compared with the available literature data. Spreading tests on Cu of Sn-8.8Zn alloys with 0.5, 1.0, and 1.5 at.% of In were performed. Wetting tests were performed at 250 °C, by sessile drop method, by means of flux, and wetting times were 3, 8, 15, 30, and 60 min. In general, no clear effect of wetting time on spreading was observed.     

Innovative method of Transthoracic Lung Cancer Biopsy of Parietal Lung Tumors under US Guidance after CT Pre-biopsy Planning as an Alternative to CT- Guided Biopsy

The authors compared their earlier results of the tumor biopsies performed under computer tomography （CT） guidance against the results of their recently modified-combined method of visualization and measurement of lung tumor parameters by CT imaging followed by US guided biopsy. In 238 （6.36%） of 3,745 patients in CT examination, the lung tumor was located peripherally, and obtaining histopathological confirmation was crucial to start the proper treatment. The patients were divided into two groups, the division was based on the biopsy method. Within the first group in I 18 patients, parietal lung tumor was confirmed and CT guided biopsy was performed. Within the second group, parietal lung tumor was confirmed in 120 patients and combined method of CT pre- biopsy planning and US guided biopsy were used. Pre-biopsy planning was performed using CT, measurements such as depth and distance of the tumor were made, obtained data were then saved on CT image and patient＇s skin was marked. Then obtained results were analyzed using test for two proportions. The analysis of the results confirmed the higher efficacy of the combined method taking into account the number of complications （p 〈 0.01） and diagnostic histopathological results （P 〈 0.001）. Suggested innovative method, involving both CT pre-biopsy planning and US guided biopsy, allows to analyze simultaneously static CT and dynamic US images and it is considered to be an easy and effective method comparing to relying on static in nature CT images only. Our method is related to a lower complication risk rate.     

Surface layer condition and the fatigue strength of an AZ91 alloy after ball peening

The present work compares the states of the surface textures and the oscillatory fatigue strengths of specimens made of an AZ91 alloy after turning and dynamic bearing ball peening. It was found that the specimens ball peened at different time have similar surface geometric structure parameters but different strengthening intensity. It was shown that fatigue strength follows greater peening intensity and random and isotropic surface. It was also ascertained that improving (by peening) the condition of the surface layer means enhancing fatigue strength by 20–87% compared with turning.     

Transistor Paint: Environmentally Stable N‐alkyldithienopyrrole and Bithiazole‐Based Copolymer Thin‐Film Transistors Show Reproducible High Mobilities without Annealing

New solution processable 4‐(2‐hexyldecan)‐4H‐bisthieno[2,3‐d:3′,2′‐b]pyrrole and 4,4′‐dialkyl‐2,2′‐bithiazole‐based copolymers (PBTzDTPs) are synthesized with excellent FET performance. These novel copolymers have considerable potential in printable electronics as they have high charge carrier mobilities, excellent air stability, good solution processibility, and no requirement for post‐deposition thermal annealing, all requirements for this field of application. The thin film transistors fabricated from PBTzDTPs achieve field effect mobilities as high as 0.14 cm² V^?1 s^?1 with current on/off ratios up to 10⁶ without thermal annealing. In addition, the devices exhibit stable performance in air, showing no significant degradation over 60 days. Moreover, the polymers described here provide an excellent example of the systems in which higher mobility performance does not require higher crystalline, long‐range ordered structures. Such a system appears to be particularly promising for rapid fabrication techniques, where kinetic conditions usually prevent the development of long‐range order.     

Deposition of calcium hydroxyapatite on negatively charged polyphosphazene surfaces

A number of polyphosphazenes with negatively charged β‐alanine (β‐Ala) and γ‐amino butyric acid (GABA) side groups were synthesized and studied for their ability to initiate the growth of hydroxyapatite (HAp) during exposure to simulated body fluid (SBF). All the polymers were hydrolytically sensitive, with the final hydrolysis rate dependent on the specific active side groups (GABA > β‐Ala). These systems also underwent extensive mineralization, with calcium phosphate deposited across their entire surface during exposure to SBF (up to 115 wt % gain after 4 weeks). This degree of deposition is a major advance over previously reported polyphosphazene systems, which underwent a maximum of 27 wt % gain after immersion in SBF for 4 weeks. The extent of mineralization over the surface was monitored using environmental scanning electron microscopy (ESEM) coupled with energy dispersive X‐ray spectroscopy (EDS). In addition, X‐ray diffraction (XRD) was used to determine the identity of the mineralized material. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41741.     

The Impact of Linseed Oil Lipids on the Physical Properties of Corn Crisps and the Possibility of Obtaining Crisps Enriched with n‐3 Fatty Acids

Linseed oil, also known as flaxseed oil, is obtained from the dried, ripened seeds of the flax plant (Linum usitatissimum). The oil is obtained by pressing, sometimes followed by solvent extraction supported by a refining process. Linseed oil is an edible oil that is in demand as a nutritional supplement, as a source of α‐linolenic acid an n‐3 fatty acid. The aim of this work was to investigate: (1) the influence of the corn crisp extrusion process on the degradation of fatty acids in linseed oil (LO) and some preparations obtained from the linseed oil such as ethyl ester (EE) and free fatty acids (FFA) added to the corn in order to increase the nutritional value of the crisps, (2) influence of the oil and two fatty preparations obtained from it on the quality of corn crisps, (3) interaction of the lipid fraction with starch. The extrusion process did not degrade the fatty acids significantly. Expansion ratio obtained in the corn crisp extrusion process decreased from 620 % down to 153 %, the size of pores/thickness of the starch–protein walls forming the structure of the extruded product decreased from 10 μm down to 4 μm, the hardness of the crisps increased from 20 to 75 N, and number of lipid–starch complexes increased with rising polarity of the lipid fraction. FFA were complexed mostly by starch (about 90 %), to a lesser degree by EE (about 60 %) and to the least extent by triacylglycerols (about 10 %). The studies performed under industrial conditions using the single screw extruder for the production of corn crisps with the application of standard parameters of the extrusion process indicated that the addition of a mass of 5 % of the various lipids (triacylglycerols of linseed oil, ethyl esters and fatty acids obtained from linseed oil) to corn grits prior to the extrusion process significantly affect the quality of corn crisps.