Quantitative liver ADC measurements using diffusion-weighted MRI at 3 Tesla: evaluation of reproducibility and perfusion dependence using different techniques for respiratory compensation

Object

Diffusion weighted imaging (DWI) of the liver suffers from low signal to noise making 3 Tesla (3 T) an attractive option, but 3 T data is scarce. It was the aim to study the influence of different b values and respiratory compensation methods (RCM) on the apparent diffusion coefficient (ADC) level and on ADC reproducibility at 3 T.

Materials and methods

Ten healthy volunteers and 12 patients with malignant liver lesions underwent repeated (2–22 days) breathhold, free-breathing and respiratory triggered DWI at 3 T using b values between 0 and 1,000 s/mm².

Results

The ADCs changed up to 150 % in healthy livers and up to 48 % in malignant lesions depending on b value combinations. Best ADC reproducibility in healthy livers were obtained with respiratory triggering (95 % limits of agreement: ±0.12) and free-breathing (±0.14). In malignant lesions equivalent reproducibility was obtained with less RCM dependence. The use of a lower maximum b value (b = 500) decreased reproducibility (±0.14 to ±0.32) in both normal liver and malignant lesions.

Conclusion

Large differences in absolute ADC values and reproducibility caused by varying combinations of clinically realistic b values were demonstrated. Different RCMs caused smaller differences. Lowering maximum b value to 500 increased limits of agreement up to a factor of two. Serial ADC changes larger than approximately 15 % can be detected confidently on an individual basis in both malignant lesions and normal liver parenchyma at 3 T using appropriate b values and respiratory compensation.     

Properties of In-Doped ZnO Films Grown by Metalorganic Chemical Vapor Deposition on GaN(0001) Templates

We investigated the properties of indium-doped zinc oxide layers grown by metalorganic chemical vapor deposition on semi-insulating GaN(0001) templates. Specular and transparent films were grown with n-type carrier concentrations up to 1.82 × 10¹⁹ cm⁻³ as determined by Hall measurements, and all In-doped films had carrier concentrations significantly higher than that of a comparable undoped film. For low In flows, the carrier concentration increased accordingly with trimethyl-indium (TMIn) flow until a maximum carrier concentration of 1.82 × 10¹⁹ cm⁻³ was realized. For higher In flows, the carrier concentration decreased with increasing TMIn flow rate. Sheet resistance as low as 185 Ω/sq was achieved for the In-doped films, which is a significant decrease from that of a comparable undoped ZnO film. Our n-type doping studies show that In is an effective dopant for controlling the n-type conductivity of ZnO.     

Kinetics of tyre char oxidation under combustion conditions

Combustion of tyre char particles with diameters between 102 and 212 μm was performed in an experimental laboratory reactor, at temperatures between 750 and 850 °C, in an oxidative atmosphere with up to 10 vol.% O₂ at 1 bar. The observed char combustion time varied from about 9 s at 750 °C to about 4 s at 850 °C. Under these conditions the experimental data indicated increasing mass transfer resistance with temperature. A diffusion reaction model was employed to study the effects of simultaneous mass transfer and kinetics in the experiments. An intrinsic reaction rate for tyre char combustion was estimated and comparison with literature data revealed good agreement.     

Design Recommendations for a FRP Bridge Deck Supported on Steel Superstructure

No appropriate provisions from either AASHTO Standard (2002) or AASHTO LRFD (2004) bridge design specifications are available for the design of fiber-reinforced polymer (FRP)-deck-on-steel-superstructure bridges. In this research, a parametric study using the finite-element method (FEM) is conducted to examine two design issues concerning the design of FRP-deck-on-steel-superstructure bridges, namely deck relative deflection and load distribution factor (LDF). Results show that the strip method specified in AASHTO LRFD specification as an approximate method of analysis, can also be applied to FRP decks as a practical method. However, different strip width equations have to be determined by either FEM or experimental methods for different types of FRP decks. In this study, one such equation has been derived for the Strongwell deck. In addition, both FEM results and experimental measurements show that the AASHTO LDF equations for glued laminated timber decks on steel stringers provide good estimations of LDF for FRP-deck-on-steel-superstructure bridges. Finally, it is found that the lever rule can be used as an appropriately conservative design method to predict the LDF of FRP-deck-on-steel-superstructure bridges.     

Kluyveromyces lactis cytoplasmic plasmid pGKL2: heterologous expression of Orf3p and proof of guanylyltransferase and mRNA-triphosphatase activities.

The predicted ORF3 polypeptide (Orf3p) of the linear genetic element pGKL2 from Kluyveromyces lactis was expressed in Bacillus megaterium as a fusion protein with a His(6X)-tag at the C-terminus for isolation by Ni-affinity chromatography. This is the first time that a yeast cytoplasmic gene product has been expressed heterologously as a functional protein in a bacterial system. The purified protein was found to display both RNA 5'-triphosphatase and guanylyltransferase activities. When the lysine residue present at position 177 of the protein within the sequence motif (KXDG), highly conserved in capping enzymes and other nucleotidyl transferases, was substituted by alanine, the guanylyltransferase activity was lost, thereby proving an important role for the transfer of GMP from GTP to the 5'-diphosphate end of the mRNA. Our in vitro data provides the first direct evidence that the polypeptide encoded by ORF3 of the cytoplasmic yeast plasmid pGKL2 functions as a plasmid-specific capping enzyme. Since genes equivalent to ORF3 of pGKL2 have been identified in all autonomous cytoplasmic yeast DNA elements investigated so far, our findings are of general significance for these widely distributed yeast extranuclear genetic elements.     

Overview of the Data Acquisition Electronics System Design for the SLAC Linear Collider Detector (SLD)

The SLD Detector will contain five major electronics subsystems: Vertex, Drift, Liquid Argon Calorimeter, Cerenkov Ring Imaging, and Warm Iron Calorimeter. To implement the approximately 170,000 channels of electronics, extensive miniaturization and heavy use of multiplexing techniques are required. Design criteria for each subsystem, overall system architecture, and the R & D program are described.     

Guest Editors' Introduction

Journal of Signal Processing Systems -     

An FT-IR Study of NO2 Reduction in Nanocrystalline NaY Zeolite: Effect of Zeolite Crystal Size and Adsorbed Water

In this study, in situ transmission FT-IR spectroscopy was employed to investigate the selective catalytic reduction (SCR) of NO₂ in nanocrystalline NaY zeolite with a crystal size of 23 nm. Two specific aspects of this reaction were explored in this study: the importance of zeolite crystal size and the effect of water on the propylene-SCR reactions.