Effect of Polyethylenimine on Hydrolysis and Dispersion Properties of Aqueous Si3N4 Suspensions

The roles of polyethylenimine (PEI) in the hydrolysis and dispersion properties of aqueous Si₃N₄ suspensions were studied in terms of the hydrolysis, adsorption, electrokinetic, and rheological measurements. It was found that the pH change of the suspensions in the acidic environment could be minimized in the presence of ≥0.5 dwb% PEI. The ammonia and oxygen measurements suggest that this phenomenon is primarily attributed to the buffer mechanism generated by the ionized PEI, instead of the protection mechanism. The constant pH enables the suspensions to retain a better stability with time at acidic pH. The adsorption of PEI on Si₃N₄ is a high-affinity type at highly basic pH, but is a low-affinity type at acidic pH. As the PEI amount increases, the adsorption shifts the isoelectric point (IEP) of Si₃N₄ from pH 5.9 to pH ∼11 until complete coverage is attained. The stability of Si₃N₄ suspensions is found to depend strongly on the saturated adsorption of PEI, which is as a function of the pH and PEI amount. Once the saturated adsorption limit is reached, the excess free PEI molecules become more detrimental to the stability with increased solid loading. The stabilization mechanisms of Si₃N₄ suspensions by PEI were discussed in detail.     

Continuous-velocity lattice gas cellular automata for miscible binary fluid and its application to simulation of interface instability

Continuous-velocity lattice gas cellular automata (CVLGA) is extended to miscible binary fluid systems. A new parameter is introduced in order to control the diffusivity of the fluids. The correlation between the diffusivity and the new parameter proves that there exists the maximum value of the diffusivity. Quantitative verifications of the model are carried out with numerical simulations of the diffusion phenomena across a falling fluid film. The model is then applied to the simulations of Rayleigh-Taylor instability during the gravitational mixing phenomena. The qualitative tendency of the growth of the interface instability is the same as that obtained in conventional numerical methods.     

Determination of the glass transition temperature of polymer/layered silicate nanocomposites from positron annihilation lifetime measurements

The glass transitions of acrylonitrile-butadiene rubber (NBR)/organoclay nanocomposites with various silicate contents were investigated using positron annihilation lifetime spectroscopy (PALS). The nanocomposites were prepared through melt intercalation of NBR with various concentrations of organoclay (OC30B) modified with the organic modifier, methyl tallow bis(2-hydroxyethyl) quaternary ammonium (MT2EtOH), i.e., Cloisite^® 30B. X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HR-TEM) measurements of the NBR/OC30B nanocomposites showed that the NBR chains were intercalated between the silicate layers, thereby increasing the gallery heights of the organosilicates. The glass transition temperature of NBR was determined using differential scanning calorimetry (DSC). However, it seemed to be very difficult to clearly resolve the very small differences in T_gs caused from various loading of nanosized silicate in NBR/OC30B nanocomposites. Hence, we performed positron annihilation lifetime spectroscopy (PALS) on NBR/OC30B nanocomposites containing various amounts of OC30B (1-10 wt%). Significant changes in the temperature dependencies of free volume parameters (i.e., lifetimes and intensities) were observed at the transition temperature, T_g,PALS, and the T_g,PALS values were found to increase with increasing organoclay content in the samples. These observations are consistent with PALS having a higher sensitivity in the detection of very small changes in free volume properties. The present findings thus highlight the usefulness of PALS for studying phase transition phenomena in polymeric materials with nanoscale structural variations.     

Thermal Behavior of BaTiO3 Particles Synthesized by Plasma Chemical Vapor Deposition

The thermal behavior of nanoparticles BaTiO₃, prepared by a radio-frequency plasma chemical vapor deposition (RF-plasma CVD) method, was characterized by various analysis methods. The BaCO₃ phase was included in the powder as byproducts, which is also observed in hydrothermal BaTiO₃ powder. The BaCO₃ phase decomposed and disappeared by annealing at 873 K for 30 min. H₂O, N₂, CO₂ and H₂, were detected by a thermal desorption spectra measurement from BaTiO₃ powder. The annealed powder became well-crystallized particles without grain growth, although as-prepared powder included polycrystalline particles. We successfully observed in-situ grain growth for BaTiO₃ nanoparticles by thermal transmission electron microscope. At the initial step of normal grain growth, very fine particles with 40–60 nm diameters started to merge into the larger grains around 1083 K. The migration rate was measured by video images and a grain boundary diffusion coefficient D_gb was calculated.     

Evaporation characteristics of multi-component fuel

The maximum liquid phase penetration and evaporation behavior was investigated by using simultaneous measurement for mie-scattered light images and shadowgraph ones. The objective of this study was to analyze effect of variant parameters and fuel properties on evaporation behavior, and to investigate liquid phase penetration for the single- and multi-component fuels. The experiments were conducted in a constant-volume vessel with optical access. Fuel was injected into the vessel with electronically controlled common rail injector. It was observed that: liquid phase length is influenced by fuel properties. High-boiling point fuel within the multi-component fuel controls liquid phase length.     

Evaluation of the microstructure and melting behavior of drawn polypropylene fibers with a microthermal analyzer

The strong correlation of melting behavior with the microstructure of original and zone‐drawn isotactic polypropylene fibers was evaluated by microthermal analysis (micro‐TA) combined with wide‐angle X‐ray diffraction analysis. The crystal structure of both the original and zone‐drawn fibers was a monoclinic α‐form with a ～ 0.64 nm, b ～ 2.03 nm, and c ～ 0.65 nm. In contrast to the absence of any oriented polymer molecules in the original fiber, the polymer molecules in the zone‐drawn fiber were extended and highly oriented in at least two different states; one arranged along the drawn axis and the other at 40° to the drawn axis. The micro‐TA‐derived melting points corresponded to these microstructural changes caused by the zone‐drawing process and differed from the melting points obtained by differential scanning calorimetery. The micro‐TA melting point of 140°C corresponded to the z‐e‐p melting point of the original fiber, being much lower than the conventional differential scanning calorimetery melting point of 163°C. As for the zone‐drawn fiber, an increase of 19°C in the melting temperature revealed its high orientation level, and the appearance of three elevated melting peaks (161, 167, and 178°C) at the highest heating rate (1500°C/min) coincided with its several oriented states. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1306–1311, 2006     

Partial oxidation of ethane to synthesis gas over Co-loaded catalysts

Attention has been increasingly paid to the partial oxidation of lower alkanes to synthesis gas, due to its intrinsic energy saving process. We studied the partial oxidation of ethane (POE) on Co loaded on various supports. The POE performance varied as follows: Y₂O₃, CeO₂, ZrO₂, La₂O₃  SiO₂, Al₂O₃, TiO₂ > MgO. Comparing Y₂O₃ and CeO₂, the carbon deposition during the POE was negligible on CeO₂ and therefore CeO₂ was the most preferable support. By changing space velocity and O₂ partial pressure, reaction mechanism of POE was studied and it was revealed that two-step mechanism was prevailing; combustion of ethane to H₂O and CO₂ and subsequent reforming of ethane with H₂O and CO₂ to synthesis gas. Co/CeO₂ catalyst exhibited high and stable catalytic activity for 10 h; high ethane conversion of 18% (maximum ethane conversion 20% at O₂/C₂H₆ = 0.2) with H₂ and CO selectivities of 93 and 84%, respectively.     

Fate of the chlorine and fluorine in a sub-bituminous coal during pyrolysis and gasification

The fate of the chlorine and fluorine present in a sub-bituminous coal from Indonesia during pyrolysis and gasification has been studied with fixed and entrained bed reactors. The rate profile for HCl evolved in the temperature programmed pyrolysis exhibits the main and shoulder peaks at 480 and 600 °C, respectively. Model experiments and subsequent Cl 2p XPS measurements show that HCl reacts with metal impurities and carbon active sites at 500 °C to be retained as inorganic and organic chlorine forms, from which HCl evolves again at elevated temperatures. It is suggested that the HCl observed in the coal pyrolysis may originate from the above-mentioned chlorine functionalities formed by secondary reactions involving the nascent char. In the CO₂ gasification of the 900 °C char at 1000 °C and 2.5 MPa, any measurable amounts of HCl and HF could not be detected even at a high conversion of 75 wt% (daf), suggesting the accumulation of these halogens in the residual char. When the coal is injected into an O₂-blown, entrained bed gasifier at 1200-1400 °C under 2.6 MPa, the partial oxidation proceeds to a larger extent at a higher O₂/coal ratio, whereas the chlorine and fluorine are enriched in the remaining char, and the extent of the enrichment at the latter stage of gasification is larger with the fluorine. The XPS measurements of the chars reveal the presence of the broad F 1 s peak, which can cover a wide range of binding energies attributable to inorganic and organic fluorine. The halogen enrichment during gasification is discussed in terms of secondary reactions of HCl and HF with char.     

Isotactic polypropylene hollow microfibers prepared by CO2 laser‐thinning

An isotactic polypropylene hollow microfiber was continuously produced by using a carbon dioxide (CO₂) laser‐thinning method. To prepare the hollow microfiber continuously, the apparatus used for the thinning of the solid fiber was improved so that the laser can circularly irradiate to the hollow fiber. Original hollow fiber with an outside diameter (OD) of 450 μm and an internal diameter (ID) of 250 μm was spun by using a melt spinning machine with a specially designed spinneret to produce the hollow fiber. An as‐spun hollow fiber was laser‐heated under various conditions, and the OD and the ID decreased with increasing the winding speed. For example, when the hollow microfiber obtained by irradiating the CO₂ laser to the original hollow fiber supplied at 0.30 m min^?1 was wound up at 800 m min^?1, the obtained hollow microfiber had an OD of 6.3 μm and an ID of 2.2 μm. The draw ratio calculated from the supplying and the winding speeds was 2667‐fold. The hollow microfibers obtained under various conditions had the hollowness in the range of 20–30%. The wide‐angle X‐ray diffraction patterns of the hollow microfibers showed the existence of the highly oriented crystallites. Further, the OD and ID decreased, and the hollowness increased by drawing hollow microfiber obtained with the laser‐thinning. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2600–2607, 2006