Shifts in biodegradation kinetics of the herbicides MCPP and 2,4-D at low concentrations in aerobic aquifer materials

Biodegradation kinetics of two phenoxy acid herbicides, MCPP [(+/-)-2-(4-chloro-2-methylphenoxy)propanoic acid; mecoprop] and 2,4-D [2,4-dichlorophenoxyacetic acid] were studied in laboratory batch microcosms at low concentrations (0.025-100 microg/L) using 14C technique with sediments and groundwater from a shallow aerobic sandy aquifer. Below a certain threshold concentration of approximately 1 microg/L for 2,4-D and 10 microg/L for MCPP, the biodegradation followed first-order nongrowth kinetics, and no adaptation was observed within the experimental period of 341 d. Half-lifes for ultimate degradation were 500 d for 2,4-D and 1100 d for MCPP at 10 degrees C in unpolluted aquifer sediment in this environmentally relevant concentration regime. Above the threshold concentrations, the biodegradation rate accelerated gradually due to selective growth of specific biomass, which was ascertained from 14C most probable number enumerations of specific phenoxy acid degraders. Atthe highest concentration tested (100 microg/ L), specific degraders increased from 10(-1) to 10(5) cells/g during the experiment, and half-lifes after adaptation decreased to approximately 5 d. The enhanced rate of degradation by adapted systems was maintained during degradation of the last residuals measured to less than 0.1 microg/L. In situ long-term preexposure of the aquifer sediment also resulted in significant higher degradation rates of the phenoxy acids.     

Injection molding of 316L stainless steel microstructures

Micro powder injection molding (PIM) is a promising process for low cost fabrication of three-dimensional microstructures. The PIM can be used for a wide range of metal and ceramic materials, combined with the potential for mass production. In this paper, initial study on the molding of 316L stainless steel microstructures was investigated. Three different micro-cavity shapes were used. Small powder with mean size of 4 m was used with two multi-component binder systems. Microstructures with dimension as small as 35 m could be injection molded. For successful molding, the binder system must provide high green strength to withstand ejection from the mold and suitable molding parameters used. For example, a high mold temperature is required and ejection speed must be reduced. The cross-sections of the microstructures are precisely replicated. The general shape in the depth direction is replicated although it is not as good as that for the cross-section. More work has to be conducted to realize the full potentials of the process.The authors would like to thank the Nanyang Technological University for awarding a research grant to conduct this research and Adeka Fine Chemicals (Tokyo) for the supply of PAN 250 binder.     

Adaptive Correction of Errors in Residue Coupled MASH ΔΣ Modulators

MASH delta-sigma () modulators consist of a cascade of several lower order single-loop modulators. In an ideal cascade, the quantization error from all but the last stage are digitally canceled. The drawback with a cascaded design is the requirement of precise matching of contributions from different quantizers to cancel lower order quantization noise from intermediate delta-sigma stages. This paper presents a new, adaptive improvement to the residue coupled MASH delta sigma modulator. The adaptive corrections significantly reduce the sensitivity to analog imperfections. The result is a simple MASH delta-sigma modulator with high precision. Simulations of a 1-1 MASH circuit structure with errors and corrections are included to confirm the theory.     

Geometry dependence of microstructure and microhardness for selective electron beam-melted Ti–6Al–4V parts

In an additive-manufactured metallic part, distinct and different microstructure and mechanical properties may exist in different areas due to differences in shape and location. Two parts, one with straight-finned structure and the other with curve-finned structure, were fabricated by the selective electron beam melting method using pre-alloyed Ti–6Al–4V ELI powder. Microstructural characterisation of these two parts that have varying fin thickness and shape was carried out to investigate the synthetical influence of 2D planar build geometry and in-fill hatching strategy on selective electron beam melting. It was found that the β interspacing is larger in the curve-finned structure, leading to a lower microhardness as compared to the straight-finned structure. It suggests a slower cooling rate in the curve-finned structure due to the differences in build geometry and in-fill hatching strategy.     

Sintering of LaFeO3 Ceramics

The sintering of LaFeO₃ has been studied in the temperature interval 1100–1600°C in air. The effect of cation nonstoichiometry on densification, microstructure, and phase composition is emphasized. La₂O₃ was observed to inhibit both sintering and grain growth. In Fe-excess materials, exaggerated grain growth occurred, particularly above 1430°C, where a liquid phase was formed. Postsintering swelling was observed in Fe-excess materials above 1430°C. The swelling mechanism is related to phase equilibria, which are reductive in nature and lead to the evolution of oxygen gas. The density in La-excess materials remains high up to 1600°C, but the ceramics might disintegrate in air.     

Experimental investigation of the temperature fade in the cavitation zone of full journal bearings

This paper describes an experimental investigation with a rig for measuring the surface temperatures and pressures in single bore journal bearings. The test bearing was equipped with small bores, where the pressure was altered by means of a vacuum pump. The whole bearing arrangement can also be operated at different ambient pressures ranging from atmospheric down to −0.06 MPa. Oil temperatures at inlet and outlet are also measured. Experiments show a considerable drop in the temperature of oil undergoing a drop in pressure. The overall temperature level of the bearing system did not seem to affect the magnitude of the temperature drop. Experiments where the bearing system was operated at sub-ambient pressures revealed an increased temperature drop in the cavitation zone. Pressures higher than ambient were measured within the cavitation zone while the bearing was operated at sub-atmospheric pressure. The higher pressures are believed to be caused by evaporation of oil. It is therefore proposed that the temperature drop observed in the cavitation zone of journal bearings is primarily caused by evaporation of oil. However, isentropic decompression of the gases in the oil is also believed to play a role.     

Element contents in leaves of four plant species (birch, mountain ash, fern and spruce) along anthropogenic and geogenic concentration gradients

Forty samples each of leaves of birch (Betula pubescens Ehrh.), European mountain ash (Sorbus aucuparia (L.)) and bracken fern (Pteridium aquilinum (L.) Kuhn) as well as spruce needles (Picea abies (L.) Karsten) were collected along a 120 km south-north transect running through Norway's largest city, Oslo. Concentrations of 25 chemical elements (Ag, Au, B, Ba, Ca, Cd, Co, Cr, Cu, Fe, Hg, K, La, Mg, Mn, Mo, Na, Ni, P, Pb, S, Sb, Sr, Ti, and Zn) as well as loss on ignition for the 4 sample materials are reported. The decline of input of sea spray with distance from the coast, geology, pH and anthropogenic contamination all played a role for the observed element concentrations in the leaves. Although growing under exactly the same natural conditions each plant species displayed quite unique uptake characteristics. Plant-species dependency and individual differences in the reaction of the plant leaves to different element sources make the investigated species of very limited value as bioindicators of anthropogenic activities. Anthropogenic contamination influences plant-leaf element content within a limited distance ( approximately 20 km) from the source.