New class of cellulose fiber spun from the novel solution of cellulose by wet spinning method

A novel cellulose solution, prepared by dissolving an alkali-soluble cellulose, which was obtained by the steam explosion treatment on almost pure natural cellulose (soft wood pulp), into the aqueous sodium hydroxide solution with specific concentration (9.1 wt %) was employed for the first time to prepare a new class of multifilament-type cellulose fiber. For this purpose a wet spinning system with acid coagulation bath was applied. The mechanical properties and structural characteristics of the resulting cellulose fibers were compared with those of regenerated cellulose fibers such as viscose rayon and cuprammonium rayon commercially available. X-ray analysis shows that the new cellulose fiber is crystallographically cellulose II, and its crystallinity is higher but its crystalline orientation is slightly lower than those of other commercial regenerated fibers. The degree of breakdown of intramolecular hydrogen bond at C₃[X_am(C₃)] of the cellulose fiber, as determined by solid-state cross-polarization magic-angle sample spinning (CP/MAS) ¹³C NMR, is much lower than other, and the NMR spectra of its dry and wet state were significantly different from each other, indicating that cellulose molecules in the new cellulose fiber are quite mobile when wet. This phenomenon has not been reported for so-called regenerated cellulose fibers.     

Fabrication and Microstructure Characterization of Ti3SiC2 Synthesized from Ti/Si/2TiC Powders Using the Pulse Discharge Sintering (PDS) Technique

Ti/Si/2TiC powders were prepared using a mixture method (M) and a mechanical alloying (MA) method to fabricate Ti₃SiC₂ at 1200°–1400°C using a pulse discharge sintering (PDS) technique. The results showed that the Ti₃SiC₂ samples with <5 wt% TiC could be rapidly synthesized from the M powders; however, the TiC content was always >18 wt% in the MA samples. Further sintering of the M powder showed that the purity of Ti₃SiC₂ could be improved to >97 wt% at 1250°–1300°C, which is ∼200°–300°C lower than that of sintered Ti/Si/C and Ti/SiC/C powders using the hot isostatic pressing (HIPing) technique. The microstructure of Ti₃SiC₂ also could be controlled using three types of powders, i.e., fine, coarse, or duplex-grained, within the sintering temperature range. In comparison with Ti/Si/C and Ti/SiC/C mixture powders, it has been suggested that high-purity Ti₃SiC₂ could be rapidly synthesized by sintering the Ti/Si/TiC powder mixture at relatively lower temperature using the PDS technique.     

Soluble and colorless polyimides with polyalicyclic structures [1]

Two tetracarboxylic dianhydrides with polyalicyclic structure, bicyclo[2.2.2]octane-2-endo, 3-endo, 5-exo, 6-exo-2,3:5,6-dianhydride (5a) and the all-exo isomer (5b), were synthesized in six steps using phthalic acid as a starting material. The dianhydrides were polymerized at 85–105°C in well-purified DMAc with aromatic diamines which were purified by two recrystallizations and then sublimation. The polyimides formed flexible and tough films, and were soluble in aprotic polar solvents such as DMAc. The 5%-weight loss temperatures were over 450°C. The polyimides possessed glass-transition temperatures in the range from 211 to 385°C. The polyimides films had a tensile modulus range of 1.5–2.6 GPa, a tensile strength range of 52–96 MPa, and an elongation range at break of 3–11%. The polyimide films showed cutoffs at wavelengths shorter than 320 nm and were entirely colorless. The colorlessness of the polyimide films was maintained up to 200°C when heated in air and to 400°C in a N₂ atmosphere.     

ARCOR,a new photolithography technique with antireflective coating on resist

The multiple interference effect is one of the major causes of the fluctuation in critical dimension control (CD) and in mark detection for alignment. Suppressing this effect is critical for future photolithography. We propose a new photolithography technique called anti reflective coating on resist (ARCOR), which improves linewidth accuracy and overlay accuracy by suppressing multiple interference. ARCOR consists of relatively simple processes: A clear antireflective film is spun onto the resist prior to the mark detecting for alignment and exposure. The film is subsequently removed and the resist developed in the conventional way. ARCOR differs from ARC, which suppresses the reflection at the resist/substrate interface. ARCOR suppresses the reflection at the air/resist interface. ARCOR allows mark detection and exposure without light intensity-loss and multiple interference. The experiments mainly examine polysiloxane and perfluoroalkylpolyether as ARCOR materials. It is shown that linewidth accuracy can be improved from 0.3 to 0.03 μm. The signal-to-noise ratio of the alignment signal is drastically improved, and the overlay error is about half that of the conventional method. ARCOR is also effective for directly measuring the reflectivity at the resist/substrate interface, which is a key parameter of the multiple interference effect and the halation. Using ARCOR and a thin resist film, the measured ratio of reflected light to incident light indicates the reflectivity at the resist/substrate interface. Because, the probe light does not reflect off the resist surface and the intensity-loss at the resist surface is suppressed. With perfluoroalkylpolyether film, the measurement error is ～ 1.5%.     

Antioxidizing component,musizin, inrumex japonicus houtt

A substance with antioxidant properties was obtained from the hexane extract of roots ofRumex japonicus Houtt. The active component of the hexane extract was isolated and characterized as 2-acetyl-1,8-dihydroxy-3-methyl naphthalene, trivially named musizin (MUS). The antioxidant activities of MUS in six types of fats and oils were higher than that of butyl hydroxyanisole (BHA) and δ-tocopherol (δ-TOC). Together, TOC and MUS have a synergistic effect, because comparable amounts of either had lower antioxidant activity than various combinations of the two antioxidants. When we studied the antioxidant properties of a mixture of MUS and δ-TOC with methyl linoleate (MeLH), we found that the rates of destruction of the two antioxidants were comparable, but that their destruction occurred sequentially, with MUS first followed by δ-TOC, after which the oxidation of MeLH quickly occurred. Comparison of the antioxidant activity of MUS and its analogs suggests that only one of the two hydroxyl groups in MUS is involved in its antioxidant activit. Intermolecular hydrogen bonding may be involved.     

Ceramic fibres from polymer precursor containing Si-O-Ti bonds

Polycarbosilanes containing titanium alkoxide as pendant groups (atom ratio Ti/Si = 0.07 and 0.15) were synthesized. These polymers were melt-spun and then heat-treated in a vacuum, in oxygen or ammonia gas flow, resulting in Si-Ti-C-O, Si-Ti-0 and Si-Ti-O-N fibres, respectively. The pyrolysis process of the polymer is discussed in connection with the mechanical properties and the structure of the fibre. At high heat-treatment temperatures, -SiC and TiC (in Si-Ti-C-O fibre), anatase (in Si-Ti-O fibre) and TiN (in Si-Ti-O-N fibre) crystallized, which may be closely related to the decomposition of the Si-O-Ti bond in the fibre.     

Mechanical strengthening of Si cantilever by chemical KOH etching and its surface analysis by TEM and AFM

Mechanical strengthening of a Si cantilever by applying KOH wet etching was investigated. Two kinds of Si cantilever specimens having the different crystallographic orientations of the sidewall surfaces, i.e., Si{100} and Si{110}, were fabricated from the same SOI wafer by a Bosch process. The typical height and pitch of the scalloping formed on the sidewall were 248 and 917 nm, respectively. A 50 % KOH (40 °C) chemical wet etching was applied to increase the fracture stress of the Si cantilever. The fracture stress in the both of Si{100} and Si{110} cantilevers increased with the advance of the etching. The obtained maximum fracture stress in Si{100} and Si{110} were 4.2 and 3.7 GPa, respectively. Sidewall surface of the cantilever was analyzed to investigate the mechanical strengthening of Si cantilever by wet etching. The etched surface crystalline was analyzed by the transmission electron microscope (TEM), and confirmed that the thickness of the affected flow layer was less than 10 nm from the obtained TEM image. Then the change of the surface roughness by the KOH etching was analyzed by the atomic force microscope. The surface was smoothened with the advance of the KOH etching. The roughness value of Ra in Si{100} and Si{110} decreased to 12.1 and 37.7 nm, respectively.     

Analysis of electro‐optical properties of polymer‐stabilized OCB and the application to TFT‐LCDs

Abstract— A 9‐in. full‐color polymer‐stabilized OCB TFT‐LCD with stable bend alignment in the absence of an electric field was developed. The condition of the polymer stabilization, the characteristics of UV‐curable monomers, and their influence on the configurations of the polymer network in the cell were studied. Possible models of the configuration were proposed and their relationship to the electro‐optical properties was analyzed using a novel simulation method considering the distribution of anchoring effects from both alignment surfaces and the polymer network. It was suggested that a good performance such as high contrast ratio and fast response could be expected in the polymer network originating from newly developed monomers composed of multifunctional LC acrylates due to a relatively weak‐anchoring effect and presumably its localization near the alignment surfaces. By using the newly developed monomers under the optimized polymer‐stabilizing process, a high contrast ratio of 250:1 and fast response nearly equal to that of a conventional OCB cell were achieved.     

Excitations bound to a vortex line in layered superconductors

Using Bogoliubov-de Gennes equation, we study quasiparticle excitations in layered superconductors in the presence of a straight vortex line which is parallel to the layers. The lowest bound state is shown to have energy eigenvalue of the order of magnitude , the energy gap, in contrast to the corresponding value ²/E_F when the line is perpendicular to the layers.     

Methanation of carbon deposited directly from CO2 on rhodium-bearing activated magnetite

Methanation reactivity was studied for the surface carbon deposited from CO₂ on the surface of Rh-bearing activated magnetite. The most active material (Rh=0.83 wt %) for methanation was prepared by the impregnation method at 60°C and showed 98% conversion at 300°C. The surface carbon was composed of elemental carbon (-carbon) and polymerized carbon (-carbon), the proportion being dependent on the density of carbon deposited. In temperature-programmed surface reaction, the extent of conversion of the - and -carbon to CH₄ was 0.34 (-carbon) and 0.53 (-carbon), respectively, and the total conversion was 0.87. This result indicates that not only elemental carbon but polymerized carbon (-carbon) could be converted to CH₄ on the Rh-bearing activated (-carbon) magnetite, whereas -carbon is not hydrogenated on activated magnetite.