Application of enzymatically gelled chitosan solutions to water‐resistant adhesives

An investigation was undertaken on the application of dilute chitosan solutions gelled by tyrosinase‐catalyzed reaction with 3,4‐dihydroxyphenethylamine (dopamine). The tyrosinase‐catalyzed reaction with dopamine conferred water‐resistant adhesive properties to the semidilute chitosan solutions. The viscosity of the chitosan solutions increased highly by the tyrosinase‐catalyzed reaction and the subsequent reactions between o‐quinone compounds and chitosan. These highly viscous, gel‐like modified chitosan materials were allowed to spread onto the surfaces of the glass slides, which were tightly lapped together and held them in water. Tensile shear adhesive strength of over 400 kPa was observed for the modified chitosan samples. The increase in the amino group concentration of the chitosan solutions and the molecular mass of the chitosan used effectively led to the increase in adhesive strength of the glass slides. In addition, in the case where the chitosan solution was gelled by the enzymatic reaction with dopamine in the presence of poly(ethylene glycol), adhesive strength sharply increased at shorter reaction times concomitantly with the increase in the viscosity of the chitosan solutions because the tyrosinase activity effectively was retained by poly(ethylene glycol). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1818–1827, 2007     

Development of reel-to-reel microchip mounting system for fabrication of meter-long LED lighting tapes

We have developed a reel-to-reel microchip mounting system that continuously mounts LED chips and other microchips on meter-long flexible printed circuit board (PCB) tape for 1.2-m-long standard LED light tubes. Mounting microchips on meter-long PCBs is difficult because a large chip mounter is expensive and the chip positioning stage is difficult to move in a meter-wide area with an accuracy of hundreds of micrometers. Hence, we developed a new microchip mounting system that utilizes a small chip mounter and reel winding machines. The system repeatedly moves the long PCB tape by a certain length with the reel winding machines and mounts the chips on it. The PCB tape (which is 5 mm wide) is made by fabricating long PCB tapes which are 25 cm × 26.6 m through a roll-to-roll PCB process and slitting them into meter-long tapes. The reel-to-reel system repeatedly mounts chips by adjusting their positions through image processing of the copper wiring pattern on the PCBs. Our constructed system mounted 24 LED chips with a pitch of 5 cm with an accuracy of 0.082 mm to form a 1.2-m-long LED tape. The luminance of the tape is 12.4 lx at a distance of 1 m, which is the luminance of outdoor corridor lighting. Therefore, this system can be used for meter-long tape lighting.     

Thermal strain of high strength polyethylene fiber in low temperature

High strength polyethylene fiber (Toyobo, Dyneema® fiber: hereinafter abbreviated to DF) has a negative thermal expansion coefficient. Relation between fiber structure and thermal strain of DF used as reinforcement of DF reinforced plastic (DFRP) for cryogenic use was investigated. The crystallinities and orientation angles of several kinds of polyethylene fibers having different modulus from 15 to 134Gpa (herein after abbreviated to DFs) were measured by NMR and X‐ray. We obtained the parameters of the mechanical series‐parallel model composed of crystal and amorphous by crystallinity and modulus. Thermal expansion coefficients of DFs were estimated by mechanical series‐parallel model. All DFs having different modulus showed negative thermal expansion coefficients in the temperature range from 180 to 300K, and absolute values of those markedly increased by increasing tensile modulus of DF. The estimated thermal expansion coefficients showed negative values, and thermal strains showed a similar curve to observed ones mostly. Average thermal expansion coefficients in the temperature range from 180 to 300K estimated by mechanical model agreed with the observed ones. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2918–2925, 2004     

Shape memorizing properties of a hydrogel of poly(vinyl alcohol)

Hydrogel prepared by repetitive freezing and thawing of poly(vinyl alcohol) aqueous solution was chemically crosslinked with glutaraldehyde. The chemically crosslinked hydrogel hardly changed its physical appearance, and showed good elasticity and strength as original gel. However, after treating in boiling water, it swelled a little, depending on the condition of the chemical treatment. The melted gel thus obtained showed shape memorizing property, that is, it could firmly hold nearly 200% of strain, keeping its original high elasticity. The strain could be released very quickly (< 1 s) in boiling water, and the gel was suggested to be applied to a new type of gel actuator. X-ray diffraction study revealed that the melted gel does not necessarily reform the physical crosslinks in exactly the same manner as the original gel in the process of shape restoring, but the distribution of the physical crosslinks can be restored as they were. It was suggested that the chemical crosslinks which remember the distribution of the physical crosslinks plays a critical roll in the shape restoring process.     

Preparation and structure of poly(vinyl alcohol)–poly(vinyl acetate) composite porous membrane

The preparation of poly(vinyl alcohol) (PVA)–poly(vinyl acetate) (PVAc) composite porous membrane was investigated by extracting PVAc with solvent from films of PVAc lattices which were obtained by the emulsion polymerization of vinyl acetate (VAc) in the presence of PVA. The formation of the porous membrane depended upon whether or not PVAc in the latex film was easily extracted with solvent. In the case of using hydrogen peroxide (HPO)–tartaric acid (TA) as an initiator, in the film of the latex which was produced from the batch method in which all ingredients of the batch were put into the reaction vessel before starting polymerization, PVAc could be extracted over 90% of total PVAc with common organic solvents. In the film of the latex which was produced from the dropwise addition method of VAc and initiator, the PVAc extraction was about 20-30%. On the other hand, in the case of using ammonium persulfate as an initiator, the desired porous membrane was not obtained. The structure of the porous membrane obtained from the latex of the batch method by using HPO—TA consisted of spherical cells which were made up of PVA and grafted PVAc or insoluble PVAc like microgels, which were not extracted with organic solvent and were connected by small pores. The PVA—PVAc composite porous membrane is permeated by n-hexane with 5.58 × 10² mL/cm²·s at 0.5 kg/cm², by benzene with only 1.33 × 10^?3mL/cm²·s even at 60 kg/cm².     

Iodine reaction of vinyl acetate/vinyl propionate copolymers. III. Iodine affinities of the radically polymerized copolymers and the copolymers derived from partially saponified polyvinyl acetate

The minimum sequence lengths (n_c) of vinyl acetate (VAc) units necessary to form a colored iodine complex were determined to be 4 and 17 for radically polymerized VAc/vinyl propionate (VPr) and VAc/isopropenyl acetate (IPAc) copolymers, respectively. The iodine affinities (I/VAc) of VAc/VPr copolymers (SP-series) obtained by propionylation of partially saponified polyvinyl acetate (PVAc) were remarkably affected by the saponification conditions. An increase of the water content in acetone/water mixture as saponification solvent brought about a decrease of the iodine affinities of the SP-series. The dependence of the iodine affinity on the saponification of monomer units in the SP-series was compared with that in the radically polymerized VAc/VPr copolymers by taking the sequence probability as the measure of monomer unit distribution. The results strongly supported an occurence of the slide fastener reaction at high degrees of saponification, which was well-known in the saponification of PVAc. Furthermore, it was found that the saponification mode of PVAc at low degrees of saponification was influenced uniquely by the water content in saponification solvents and the saponification temperature.     

Critical temperature for production of MAG by esterification of different FA with glycerol using <Emphasis Type="Italic">Penicillium camembertii</Emphasis> lipase

Production of MAG by a lipase-catalyzed reaction is known to be effective at low temperature. This phenomenon can be explained by assuming that synthesized MAG are excluded from the reaction system because MAG, which have low m.p., are solidified at low temperatures. Consequently, MAG are efficiently accumulated and do not serve as the precursor of DAG. If this hypothesis is correct, the critical temperature for MAG production, defined as the highest temperature at which DAG synthesis is repressed, should depend on the m.p. of the MAG. Esterification of FFA with glycerol using Candida rugosa, Rhizopus oryzae, and Penicillium camembertii lipases produced MAG efficiently at low temperatures. However, Candida lipase showed very low esterification activity at high temperatures (>20°C), and Rhizopus lipase produced not only MAG but also DAG even at low temperatures. Meanwhile, P. camembertii lipase catalyzed synthesis of MAG only from FFA and glycerol at low temperatures, although the enzyme catalyzed synthesis of DAG from MAG in addition to synthesis of MAG at high temperatures. We thus studied the effect of temperature on esterification of C₁₀−C₁₈ FFA with glycerol using Penicillium lipase as a catalyst and determined the critical temperatures for production of MAG. The critical temperature for production of each MAG showed a linear correlation with m.p. of the MAG, which supported the hypothesis. In addition, because the m.p. of MAG are estimated from that of the constituent FA, the optimal temperature for production of MAG can be predicted from the m.p. of the FFA used as a substrate.     

Preparation of Porous Ceramics with Calcium Metaphosphate Fiber Skeleton for Biomedical Use

High-strength calcium metaphosphate fibers for biomedical applications are extracted from crystallized products of calcium ultraphosphate glasses by aqueous leaching. In the present work, new types of porous ceramics with a skeleton composed of the crystalline fibers are prepared by heating the fibrous products extracted. The fibers in the ceramic are interlinked to each other by glassy phases formed during the heating. This porous material has a large porosity of >60%. The surface of the skeleton can be successfully converted into new calcium phosphate phases such as apatite by heating the porous material treated with a molten salt mixture of CaCl₂-Ca(NO₃)₂.     

Sterols ofKalanchoe pinnata: First report of the isolation of both C-24 epimers of 24-alkyl-Δ25-sterols from a higher plant

Eighteen sterols were isolated from the aerial parts ofKalanchoe pinnata (Crassulaceae) including four novel sterols,viz. (24R)-stigmasta-5,25-dien-3β-ol (24-epiclerosterol), (24R)-5α-stigmasta-7,25-dien-3β-ol, 5α-stigmast-24-en-3β-ol, and 25-methyl-5α-ergost-24(28)-en-3β-ol. 24-Epiclerosterol and its Δ⁷-analog occur together with their 24S/β-epimers in the same plant making this the first report of the isolation of both C-24 epimers of Δ²⁵-unsaturated 24-alkylsterols from a non-marine organism. Iodine-catalyzed isomerization of stigmasta-5,24-dien-3β-ol (24-ethyldesmosterol), the main sterol ofK. pinnata, yielded 24-epiclerosterol among other products.