Crystallographic Texture Development in Bismuth Sodium Titanate Prepared by Reactive-Templated Grain Growth Method

Bi_0.5Na_0.5TiO₃ (BNT) and 0.94Bi_0.5Na_0.5TiO₃·0.06BaTiO₃ (BNT–BT) bulk ceramics with extensive 〈100〉 texture were prepared by the reactive-templated grain growth method, using platelike Bi₄Ti₃O₁₂ (BIT) particles as templates for BNT. Calcined compacts were composed of matrix grains with random orientation and 〈100〉-oriented grains transformed from aligned BIT particles, and the texture developed by the growth of oriented grains during sintering. Ceramics with extensive texture were obtained by using the starting mixture containing the maximum concentration of platelike BIT to form the maximum volume fraction of oriented grains.     

WATER MIST FLOW IN A SUPERCONDUCTING MAGNET INCLINED AT VARIOUS ANGLES

Water mist (diamagnetic) flow in a superconducting magnet of 10 T at various angles is studied experimentally and numerically. Water mist is produced by ultrasonic atomizers and fed into a cylindrical Plexiglas pipe (inner diameter, 90 mm) placed in a bore space of an inclined superconducting magnet. The water mist is found to stop at some locations in the magnet at inclined angles ψ ≤ π/6. At ψ ≥ π/4, the amount of mist flowing out of the other opening of the pipe increases with an increase in inclined angle. In the computation of this phenomenon, water mist is simulated with 1000 water droplets of 3 μm diameter. Brownian motion is considered and the Langevin equation is solved. The numerical results show that at ψ ≤ π/6, most of the water droplets accumulate above the magnetic coil. However, at ψ ≥ π/4, with an increase in inclined angle, the number of water droplets passing through the magnetic coil increases.     

Thermal behavior of hydrostatically extruded polycarbonate and high-impact polystyrene

Effects of hydrostatic extrusion on the thermal properties of polycarbonate (PC) and of high-impact polystyrene (HIPS) were studied using differential scanning calorimeter (DSC) measurements. A glass transition temperature (T_g) and a peak temperature were determined from the DSC curves for both PC and HIPS extrudates. The T_g values of the PC extrudates, with a percentage reduction in area, R, from 40 to 50%, change appreciably from the value for the as–received PC. The results of the hydrostatic extrusion of the PC billets suggest that a two stage deformation process of molecular chains may be involved. Shear-banding is observed for HIPS extrudates with R = 30 to 60%; this fact indicates that a sub-glass transition (β-transition) occurs at temperatures below T_g. It is suggested that the molecular chains of the HIPS extrudate with R = 70% are oriented in the direction of hydrostatic extrusion. The deformation mechanism of molecular chains caused by the hydrostatic extrusion is discussed.     

Shape memorizing properties of a hydrogel of poly(vinyl alcohol)

Hydrogel prepared by repetitive freezing and thawing of poly(vinyl alcohol) aqueous solution was chemically crosslinked with glutaraldehyde. The chemically crosslinked hydrogel hardly changed its physical appearance, and showed good elasticity and strength as original gel. However, after treating in boiling water, it swelled a little, depending on the condition of the chemical treatment. The melted gel thus obtained showed shape memorizing property, that is, it could firmly hold nearly 200% of strain, keeping its original high elasticity. The strain could be released very quickly (< 1 s) in boiling water, and the gel was suggested to be applied to a new type of gel actuator. X-ray diffraction study revealed that the melted gel does not necessarily reform the physical crosslinks in exactly the same manner as the original gel in the process of shape restoring, but the distribution of the physical crosslinks can be restored as they were. It was suggested that the chemical crosslinks which remember the distribution of the physical crosslinks plays a critical roll in the shape restoring process.     

Preparation and structure of poly(vinyl alcohol)–poly(vinyl acetate) composite porous membrane

The preparation of poly(vinyl alcohol) (PVA)–poly(vinyl acetate) (PVAc) composite porous membrane was investigated by extracting PVAc with solvent from films of PVAc lattices which were obtained by the emulsion polymerization of vinyl acetate (VAc) in the presence of PVA. The formation of the porous membrane depended upon whether or not PVAc in the latex film was easily extracted with solvent. In the case of using hydrogen peroxide (HPO)–tartaric acid (TA) as an initiator, in the film of the latex which was produced from the batch method in which all ingredients of the batch were put into the reaction vessel before starting polymerization, PVAc could be extracted over 90% of total PVAc with common organic solvents. In the film of the latex which was produced from the dropwise addition method of VAc and initiator, the PVAc extraction was about 20-30%. On the other hand, in the case of using ammonium persulfate as an initiator, the desired porous membrane was not obtained. The structure of the porous membrane obtained from the latex of the batch method by using HPO—TA consisted of spherical cells which were made up of PVA and grafted PVAc or insoluble PVAc like microgels, which were not extracted with organic solvent and were connected by small pores. The PVA—PVAc composite porous membrane is permeated by n-hexane with 5.58 × 10² mL/cm²·s at 0.5 kg/cm², by benzene with only 1.33 × 10^?3mL/cm²·s even at 60 kg/cm².     

In Situ Synthesis and Microstructures of Tungsten Carbide-Nanoparticle-Reinforced Silicon Nitride-Matrix Composites

A W₂C-nanoparticle-reinforced Si₃N₄-matrix composite was fabricated by sintering porous Si₃N₄ that had been infiltrated with a tungsten solution. During the sintering procedure, nanometer-sized W₂C particles grew in situ from the reaction between the tungsten and carbon sources considered to originate mainly from residual binder. The W₂C particles resided in the grain-boundary junctions of the Si₃N₄, had an average diameter of ∼60 nm, and were polyhedral in shape. Because the residual carbon, which normally would obstruct sintering, reacted with the tungsten to form W₂C particles in the composite, the sinterability of the Si₃N₄ was improved, and a W₂C–Si₃N₄ composite with almost full density was obtained. The flexural strength of the W₂C–Si₃N₄ composite was 1212 MPa, ∼34% higher than that of standard sintered Si₃N₄.     

Iodine reaction of vinyl acetate/vinyl propionate copolymers. III. Iodine affinities of the radically polymerized copolymers and the copolymers derived from partially saponified polyvinyl acetate

The minimum sequence lengths (n_c) of vinyl acetate (VAc) units necessary to form a colored iodine complex were determined to be 4 and 17 for radically polymerized VAc/vinyl propionate (VPr) and VAc/isopropenyl acetate (IPAc) copolymers, respectively. The iodine affinities (I/VAc) of VAc/VPr copolymers (SP-series) obtained by propionylation of partially saponified polyvinyl acetate (PVAc) were remarkably affected by the saponification conditions. An increase of the water content in acetone/water mixture as saponification solvent brought about a decrease of the iodine affinities of the SP-series. The dependence of the iodine affinity on the saponification of monomer units in the SP-series was compared with that in the radically polymerized VAc/VPr copolymers by taking the sequence probability as the measure of monomer unit distribution. The results strongly supported an occurence of the slide fastener reaction at high degrees of saponification, which was well-known in the saponification of PVAc. Furthermore, it was found that the saponification mode of PVAc at low degrees of saponification was influenced uniquely by the water content in saponification solvents and the saponification temperature.     

New type of tin support for hydroprocessing catalyst

TiN supported molybdenum sulfide catalysts showed much higher activity for cleavage of C-C bonds than oxide supported molybdenum sulfide catalysts, indicating the possibility of a new generation of supports for hydroprocessing catalysts.     

On-chip fabrication of magnetic alginate hydrogel microfibers by multilayered pneumatic microvalves

Alginate hydrogel has widespread applications in tissue engineering, cancer therapy, wound management and drug/cell/growth factor delivery due to its biocompatibility, hydrated environment and desirable viscoelastic properties. However, the lack of controllability is still an obstacle for utilizing it in the fabrication of 3D tissue constructs and accurate targeting in mass delivery. Here, we proposed a new method for achieving magnetic alginate hydrogel microfibers by dispersing magnetic nanoparticles in alginate solution and solidifying the magnetic alginate into hydrogel fiber inside microfluidic devices. The microfluidic devices have multilayered pneumatic microvalves with hemicylindrical channels to fully stop the fluids. In the experiments, the magnetic nanoparticles and the alginate solution were mixed and formed a uniform suspension. No aggregation of magnetic nanoparticles was found, which is crucial for flow control inside microfluidic devices. By regulating the flow rates of different solutions with the microvalves inside the microfluidic device, magnetic hydrogel fibers and nonmagnetic hydrogel fibers were fabricated with controlled sizes. The proposed method for fabricating magnetic hydrogel fiber holds great potential for engineering 3D tissue constructs with complex architectures and active drug release.     

Effect of EFA deficiency on lipid transport from liver

Studies are reported of the effect of an essential fatty acid (EFA) deficiency on synthesis of triglycerides (TG) and phospholipids (PL) and secretion of these compounds by livers of male Sprague-Dawley rats. Animals were fed a semipurified diet containing corn oil or hydrogenated coconut oil (HCO) as the sole source of fat or no fat from weaning to 20 weeks of age. Liver function of the animals in each group was compared by an isolated liver perfusion technique with perfusates containing erythrocytes and linoleate, and in vivo experiments via tail vein injection of palmitate-³H. Perfusion experiments showed that an EFA deficiency reduced the ability of the liver to secrete TG and PL. Accumulation of TG in the liver and its diminished secretion into the blood of EFA deficient animals were demonstrated by in vivo experiments with palmitate-³H. The rate of conversion of linoleate to arachidonate and synthesis of PL was greater in livers of EFA deficient rats than in the control, corn oil fed animals. The results suggest a relationship of EFA metabolism to lipid transport. One of five papers to be published from the Symposium “Lipid Transport” presented at the AOCS Meeting, New Orleans, April 1970.