Heavy oil sorption and recovery by using carbon fiber felts

On fibrous carbon materials, including activated carbon fibers, sorption capacity for heavy oils, less viscous A-grade and more viscous C-grade, was determined. Sorption capacity depended strongly on their bulk density; the correlation was the same as that found previously on exfoliated graphite and carbonized fir fibers. On carbon fiber felts, excellent recycling performance was observed, though sorption capacity was not so high as on exfoliated graphite and carbonized fir fibers. By filtration under suction, about 90% of sorbed A-grade heavy oil could be recovered and no decrease in sorption capacity was detected even after eight cycles. By washing with solvents, n-hexane for A- and C-grade oils and A-grade oil for C-grade oil, almost 100% recovery with no marked reduction in sorption capacity was found for each cycle. For the felts of PAN-based carbon fibers, rather severe operations for oil recovery, centrifugation and squeezing with twisting, could be applied without pronounced decreases in sorption capacity and recovery ratio.     

Surface-Chemical Criteria for Optimum Adhesion

According to Bikerman, who attributes failure in adhints to a weak boundary layer, it is almost impossible and meaningless to correlate adhesive strength to surface-chemical properties of adhints. Though his assertion seems to be confirmed by the recent studies of Schonhorn and his coworkers on the methods of CASING and TCR, not a few results have yet been accumulated, which show a close relation between them. In this paper surface-chemical criteria for the optimum adhesion are investigated and the minimum interfacial tension or the maximum wetting pressure is deduced from the published data and our own as a first approximation. It is emphasized that, when critical surface tension γ_c would be used as a measure of surface-chemical properties of solid, its variability according to liquid series (nonpolar, polar and hydrogen bonding liquids) should be carefully taken into consideration. The importance is shown for polyethylene and its fluorine substituted polymers, using newly measured contact angle data and Zisman's data. Results of Levine et al. and Schonhorn et al. on adhesive shear strength with epoxy adhesives are replotted against available values of γ_c obtained by the use of hydrogen bonding liquid (γ_c^c), which are thought to reflect wetting behaviors of epoxy adhesives quite well. Each curve shows a maximum around γ_c^c = 40 dyne/cm with few points falling off the curves.     

DSC and TMDSC study of melting behaviour of poly(butylene succinate) and poly(ethylene succinate)

The subsequent melting behaviour of poly(butylene succinate) (PBSU) and poly(ethylene succinate) (PES) was investigated using DSC and temperature modulated DSC (TMDSC) after they finished nonisothermal crystallization from the melt. PBSU exhibited two melting endotherms in the DSC traces upon heating to the melt, which was ascribed to the melting and recrystallization mechanism. However, one melting endotherm with one shoulder and one crystallization exotherm just prior to the melting endotherm were found for PES. The crystallization exotherm was ascribed to the recrystallization of the melt of the crystallites with low thermal stability, and the shoulder was considered to be the melting endotherm of the crystallites with high thermal stability. The final melting endotherm was ascribed to the melting of the crystallites formed through the reorganization of the crystallites with high thermal stability during the DSC heating process. TMDSC experiments gave the direct evidences to support the proposed models to explain the melting behaviour of PBSU and PES crystallized nonisothermally from the melt.     

Potential bile acid metabolites. 24. An efficient synthesis of carboxyl-linked glucosides and their chemical properties

A facile and efficient synthesis of the carboxyl-linked glucosides of bile acids is described. Direct esterification of unprotected bile acids with 2,3,4,6-tetra-O-benzyl-d-glucopyranose in pyridine in the presence of 2-chloro-1,3,5-trinitrobenzene as a coupling agent afforded a mixture of the α- and β-anomers (ca. 1∶3) of the 1-O-acyl-d-glucoside benzyl ethers of bile acids, which was separated effectively on a C₁₈ reversedphase chromatography column (isolated yields of α- and β-anomers are 4–9% and 12–19%, respectively). Subsequent hydrogenolysis of the α- and β-acyl glucoside benzyl ethers on a 10% Pd−C catalyst in acetic acid/methanol/EtOAc (1∶2∶2, by vol) at 35°C under atmospheric pressure gave the corresponding free esters in good yields (79–89%). Chemical specificities such as facile hydrolysis and transesterification of the acyl glucosides in various solvents were also discussed.     

Bending of ionic polymer gel caused by swelling under sinusoidally varying electric fields

Deformation of poly(vinyl alcohol)–poly(sodium acrylate) composite hydrogel (PVA–PAA gel) under sinusoidally varying electric fields was studied in electrolyte solutions. The PVA–PAA gel was prepared by repeatedly freezing and thawing a mixed solution of PVA and polyacrylic acid. A cyclic bending–straightening motion of the PVA–PAA gel rods of about 1 mm in diameter have been observed in Na₂CO₃ aqueous solutions under the fields. The PVA–PAA gel had a response time of less than several hundreds milliseconds. The bending has also been observed in organic solvents containing an electrolyte when the organic solvent is electrolyzed. It was found that the motion of the gel under electric fields of less than 1 Hz occurred mainly through swelling due to the change of the osmotic pressure based upon the difference of the ion concentration. However, it has not been determined whether the motion at higher frequencies is caused by the osmotic effect. © 1993 John Wiley & Sons, Inc.     

High-strength–high-modulus polyimide fibers II. Spinning and properties of fibers

The polyimides based on 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) described in Part I of this series were dissolved in p-chlorophenol and spun into fibers using a coagulating bath of ethanol. The fibers as spun had in general low tenacities and low moduli, but a heat treatment at 300–500°C under tension produced a remarkable increase in strength and modulus, and fibers with a tensile strength of 26 g/den (3.1 GPa) and an initial modulus higher than 1,000 g/den (120 GPa) could be obtained. Thus, the annealed fibers of polyimides are comparable to aramid fibers in mechanical properties. To heating in air and in the saturated steam, the polyimide fibers showed higher resistance than the aramid fibers. The polyimide fibers surpassed the aramid fibers in resistance to acid treatment and ultraviolet (UV) irradiation, but were inferior in resistance to alkali treatment. The annealed fibers of polyimides displayed distinct X-ray diffraction patterns. The chain repeat distance of 20.5 Å determined on the fibers of polyimide prepared from BPDA and o-tolidine, and 20.6 Å determined on the fibers of polyimide derived from BPDA and 3,4′-diaminodiphenyl ether are reasonable when the dimensions of monomeric units and the shapes of the molecular chains are considered. The X-ray reflections of both polyimide fibers were indexed satisfactorily on the basis of postulated unit cells.     

Copper ⇌ Alkali Ion Exchange of Alkali Aluminosillcate Glasses in Copper-Containing Molten Salt: I, Monovalent Copper Salt, CuCl

Cu⁺⇌ R⁺ (R = Li, Na, and K) ion exchange experiments were conducted for 20R₂O·10Al₂O₃·70SiO₂ glasses in molten CuCl at 550°C in air and nitrogen atmospheres. The depth profiles of the copper incorporated into glasses were determined with an electron microprobe X-ray analyzer. The total amount of diffusing copper, M _t, strongly depended on the type of alkali ion in the glass and the ion-exchange atmosphere; i.e., M _t increased with increasing cationic size in the order Li < Na < K and M _t was greater in air than in nitrogen. The Cu ⇌ R⁺ ion exchange kinetics are discussed in detail.     

Tribological Characteristics of SiC Ceramics in High-Temperature and High-Pressure Water

The effects of temperature and sliding speed on the tribological behavior of a SiC ceramic by sliding on the same material in deoxygenated water were investigated from room temperature to 300°C under the corresponding saturated vapor pressures. The friction coefficient and specific wear rates of both plates and disks increased at elevated temperatures at all sliding speeds, but decreased with increasing sliding speed at 120° and 300°C. Fine mirrorlike worn surfaces were observed without wear debris under all sliding conditions. The wear mechanism appears to consist of hydrothermal oxidation of SiC and dissolution of reaction products such as silica.     

Hydrophobic effects on protein/nucleic acid interaction: enhancement of substrate binding by mutating tyrosine 45 to tryptophan in ribonuclease Tl

Hydrophobic effects on binding of ribonuclease Tl to guaninebases of several ribonucleotides have been proved by mutatinga hydrophobic residue at the recognition site and by measuringthe effect on binding. Mutation of a hydrophobic surface residueto a more hydrophobic residue (Tyr45 – Trp) enhances thebinding to ribonucleotides, including mononucleotide inhibitorand product, and a synthetic substrate-analog trinudeotide aswell as the binding to dinucleotide substrates and RNA. Enhancementson binding to non-substrate ribonucleotides by the mutationhave been observed with free energy changes ranging from –2.2 to – 3 .9 kJ/mol. These changes are in good agreementwith that of substrate binding, –2.3 kJ/mol, which iscalculated from Michaelis constants obtained from kinetic studies.It is shown, by comparing the observed and calculated changesin binding free energy with differences in the observed transferfree energy changes of the amino acid side chains from organicsolvents to water, that the enhancement observed on guaninebinding comes from the difference in the hydrophobic effectsof the side chains of tyrosine and tryptophan. Furthermore,a linear relationship between nucleolytic activities and hydrophobicityof the residues (Ala, Phe, Tyr, Trp) at position 45 is observed.The mutation could not change substantially the base specificityof RNase Tl, which exhibits a prime requirement for guaninebases of substrates.     

Degradation and geometric isomerization of poly(N-propargylamides)

The stability of several poly(N-propargylamides) was investigated in solution and in solid state on the basis of molecular weight change with time, and further their thermal stability was investigated by TGA. When the stability of poly(N-propargylamides) with varying pendent groups was compared, polymers with pendent groups of moderate size showed the highest stability in solution. Too short and too bulky pendent groups were not favorable for the stability of polymers. When poly(N-propargylheptanamide) (poly(6)) was stored in THF as solution at −20 °C in the absence of oxygen in dark, its degradation rate was the lowest. The degradation rate of poly(6) depended on the solvents used, which may be related to different solubility of oxygen in these solvents. Polymers with high cis contents degraded faster than polymers with low cis contents did. Addition of TEMPO and DPPH into the poly(6)/THF solution more or less depressed the degradation of poly(6). The degradation of polymer main chain in solution was always accompanied by the decrease of cis content, i.e. geometric isomerization from cis- to trans-structure. When the polymers were stored in the solid state at −20 °C, the polymers having alkyl pendent groups with moderate length were more stable than those with bulky pendent groups. Geometric isomerization occurred along with degradation in the solid state as well.