Bending of ionic polymer gel caused by swelling under sinusoidally varying electric fields

Deformation of poly(vinyl alcohol)–poly(sodium acrylate) composite hydrogel (PVA–PAA gel) under sinusoidally varying electric fields was studied in electrolyte solutions. The PVA–PAA gel was prepared by repeatedly freezing and thawing a mixed solution of PVA and polyacrylic acid. A cyclic bending–straightening motion of the PVA–PAA gel rods of about 1 mm in diameter have been observed in Na₂CO₃ aqueous solutions under the fields. The PVA–PAA gel had a response time of less than several hundreds milliseconds. The bending has also been observed in organic solvents containing an electrolyte when the organic solvent is electrolyzed. It was found that the motion of the gel under electric fields of less than 1 Hz occurred mainly through swelling due to the change of the osmotic pressure based upon the difference of the ion concentration. However, it has not been determined whether the motion at higher frequencies is caused by the osmotic effect. © 1993 John Wiley & Sons, Inc.     

High-strength–high-modulus polyimide fibers II. Spinning and properties of fibers

The polyimides based on 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) described in Part I of this series were dissolved in p-chlorophenol and spun into fibers using a coagulating bath of ethanol. The fibers as spun had in general low tenacities and low moduli, but a heat treatment at 300–500°C under tension produced a remarkable increase in strength and modulus, and fibers with a tensile strength of 26 g/den (3.1 GPa) and an initial modulus higher than 1,000 g/den (120 GPa) could be obtained. Thus, the annealed fibers of polyimides are comparable to aramid fibers in mechanical properties. To heating in air and in the saturated steam, the polyimide fibers showed higher resistance than the aramid fibers. The polyimide fibers surpassed the aramid fibers in resistance to acid treatment and ultraviolet (UV) irradiation, but were inferior in resistance to alkali treatment. The annealed fibers of polyimides displayed distinct X-ray diffraction patterns. The chain repeat distance of 20.5 Å determined on the fibers of polyimide prepared from BPDA and o-tolidine, and 20.6 Å determined on the fibers of polyimide derived from BPDA and 3,4′-diaminodiphenyl ether are reasonable when the dimensions of monomeric units and the shapes of the molecular chains are considered. The X-ray reflections of both polyimide fibers were indexed satisfactorily on the basis of postulated unit cells.     

Copper ⇌ Alkali Ion Exchange of Alkali Aluminosillcate Glasses in Copper-Containing Molten Salt: I, Monovalent Copper Salt, CuCl

Cu⁺⇌ R⁺ (R = Li, Na, and K) ion exchange experiments were conducted for 20R₂O·10Al₂O₃·70SiO₂ glasses in molten CuCl at 550°C in air and nitrogen atmospheres. The depth profiles of the copper incorporated into glasses were determined with an electron microprobe X-ray analyzer. The total amount of diffusing copper, M _t, strongly depended on the type of alkali ion in the glass and the ion-exchange atmosphere; i.e., M _t increased with increasing cationic size in the order Li < Na < K and M _t was greater in air than in nitrogen. The Cu ⇌ R⁺ ion exchange kinetics are discussed in detail.     

Tribological Characteristics of SiC Ceramics in High-Temperature and High-Pressure Water

The effects of temperature and sliding speed on the tribological behavior of a SiC ceramic by sliding on the same material in deoxygenated water were investigated from room temperature to 300°C under the corresponding saturated vapor pressures. The friction coefficient and specific wear rates of both plates and disks increased at elevated temperatures at all sliding speeds, but decreased with increasing sliding speed at 120° and 300°C. Fine mirrorlike worn surfaces were observed without wear debris under all sliding conditions. The wear mechanism appears to consist of hydrothermal oxidation of SiC and dissolution of reaction products such as silica.     

Hydrophobic effects on protein/nucleic acid interaction: enhancement of substrate binding by mutating tyrosine 45 to tryptophan in ribonuclease Tl

Hydrophobic effects on binding of ribonuclease Tl to guaninebases of several ribonucleotides have been proved by mutatinga hydrophobic residue at the recognition site and by measuringthe effect on binding. Mutation of a hydrophobic surface residueto a more hydrophobic residue (Tyr45 – Trp) enhances thebinding to ribonucleotides, including mononucleotide inhibitorand product, and a synthetic substrate-analog trinudeotide aswell as the binding to dinucleotide substrates and RNA. Enhancementson binding to non-substrate ribonucleotides by the mutationhave been observed with free energy changes ranging from –2.2 to – 3 .9 kJ/mol. These changes are in good agreementwith that of substrate binding, –2.3 kJ/mol, which iscalculated from Michaelis constants obtained from kinetic studies.It is shown, by comparing the observed and calculated changesin binding free energy with differences in the observed transferfree energy changes of the amino acid side chains from organicsolvents to water, that the enhancement observed on guaninebinding comes from the difference in the hydrophobic effectsof the side chains of tyrosine and tryptophan. Furthermore,a linear relationship between nucleolytic activities and hydrophobicityof the residues (Ala, Phe, Tyr, Trp) at position 45 is observed.The mutation could not change substantially the base specificityof RNase Tl, which exhibits a prime requirement for guaninebases of substrates.     

Degradation and geometric isomerization of poly(N-propargylamides)

The stability of several poly(N-propargylamides) was investigated in solution and in solid state on the basis of molecular weight change with time, and further their thermal stability was investigated by TGA. When the stability of poly(N-propargylamides) with varying pendent groups was compared, polymers with pendent groups of moderate size showed the highest stability in solution. Too short and too bulky pendent groups were not favorable for the stability of polymers. When poly(N-propargylheptanamide) (poly(6)) was stored in THF as solution at −20 °C in the absence of oxygen in dark, its degradation rate was the lowest. The degradation rate of poly(6) depended on the solvents used, which may be related to different solubility of oxygen in these solvents. Polymers with high cis contents degraded faster than polymers with low cis contents did. Addition of TEMPO and DPPH into the poly(6)/THF solution more or less depressed the degradation of poly(6). The degradation of polymer main chain in solution was always accompanied by the decrease of cis content, i.e. geometric isomerization from cis- to trans-structure. When the polymers were stored in the solid state at −20 °C, the polymers having alkyl pendent groups with moderate length were more stable than those with bulky pendent groups. Geometric isomerization occurred along with degradation in the solid state as well.     

Pervaporation membranes for ethanol–water mixture prepared by plasma polymerization. III. Perfluorocarbon membranes

Pervaporation membranes for the ethanol–water mixture were prepared by plasma polymerization of tetrafluoroethylene, perfluoropropane, and perfluoropropylene onto porous substrates. The influence of the monomers on the elemental ratio (F/C) of the polymer depositions by X-ray photoelectron spectroscopy was rather small compared with that of the W/FM parameter (W = wattage for plasma excitation, FM = mass flow rate of a monomer). The optical emission spectroscopy indicated the similarity of gaseous species formed in the plasmas. The membranes were found ethanol-permselective, showing separation coefficients (α_EtOH) around 4–7 and a wide range of permeation rates (J), 10–10^?2 kg/m² h, for the 4.8 wt % ethanol solution at 40°C. The α_EtOH of the membranes with thicker depositions could be correlated to the F/C ratios as a measure of membrane hydrophobicity. It was thought that, by making a plot α_EtOH against J values for the perfluorocarbon membranes, they could be classified into three groups on thickness of deposition. The ethanol-separation mechanisms for each group, which may contain four kinds of mass transfer schemes, i.e., distillation through larger pores, flow of sorption layer at the liquid–membrane interface, and diffusions through deposition or substrate, were also discussed.     

Thermal Response and Oxidation of Tyranno™-Fiber-Reinforced Si-Ti-C-O Matrix Composites for a Thermal Protection System in High-Enthalpy Dissociated Air

The thermal response and oxidation of Tyranno™ Lox-M fiber-reinforced Si-Ti-C-O matrix composites in high-enthalpy dissociated air was investigated in an arc jet facility (an arc wind tunnel). The maximum surface temperature reached 1310–1670°C. Catalytic recombination of oxygen and nitrogen on the composite surface under dissociated air was not significant. Surface recession was insignificant below 1600°C surface temperatures and above 5 kPa of oxygen partial pressure at the stagnation point. Passive-to-active oxidation transition of the composite agreed with Balat's theory for monolithic silicon carbide. A glass sealant prevented active oxidation of the composite for short-time exposures.     

Oxidation behavior of TiAl coated with a fine-grain Co-30Cr-4Al film

The oxidation behavior of TiAl coupons coated with a fine-grain Co-30Cr-4Al (mass %) film of about 30-m thickness has been studied at 1100–1400 K in a flow of purified oxygen at atmospheric pressure for up to 500 ks. Three oxidation stages were recognized: initial transient, parabolic, and accelerated stages. However, at 1100 K a parabolic stage continues for more than 800 ks. The activation energy for parabolic oxidation agrees with reported values for the oxidation of alumina-former alloys, although the mass gains during the parabolic stages are relatively small at 1200 and 1300 K. Micropores developed mainly at the scale/coating and coating/substrate interfaces as oxidation proceeded. This is attributable to recrystallization of the coating during oxidation and a Kirkendall effect due to preferential diffusion of Co into the substrate. The accelerated oxidation can be explained in terms of the formation of rutile mounds on the scale.     

Oxidation Behavior of Ni-3,6, 10 wt.% Al Alloys at 800°C

The oxidation behavior of Ni and Ni-3, 6, and 10Al alloys at 800°C in an N₂–O₂ gas mixture was investigated. The mass gain of each alloy depended on both the oxidation periods and Al content. NiO scale was formed on all alloy substrates accompanied by internal oxides of Al₂O₃. Many cavities were formed at the NiO/substrate interface at shorter oxidation times, and these cavities were found to be filled by metallic Ni(Al) from the matrix in the internal-oxidation zone by the development of internal oxides. The filling of cavities by Ni(Al) was more significant on higher Al alloys, which had a higher density of internal Al₂O₃. Once metallic Ni(Al) formed along the entire NiO/substrate interface, the oxidation kinetics became the same as pure Ni. It was concluded that pure Ni filling the cavities at the interface provided a diffusion path of Ni from the substrate to the NiO scale, and that controlled the oxidation kinetics.