Fabrication of Transparent, Sintered Sc2O3 Ceramics

We report here the fabrication of transparent Sc₂O₃ ceramics via vacuum sintering. The starting Sc₂O₃ powders are pyrolyzed from a basic sulfate precursor (Sc(OH)_2.6(SO₄)_0.2·H₂O) precipitated from scandium sulfate solution with hexamethylenetetramine as the precipitant. Thermal decomposition behavior of the precursor is studied via differential thermal analysis/thermogravimetry, Fourier transform infrared spectroscopy, X-ray diffractometry, and elemental analysis. Sinterability of the Sc₂O₃ powders is studied via dilatometry. Microstructure evolution of the ceramic during sintering is investigated via field emission scanning electron microscopy. The best calcination temperature for the precursor is 1100°C, at which the resultant Sc₂O₃ powder is ultrafine (∼85 nm), well dispersed, and almost free from residual sulfur contamination. With this reactive powder, transparent Sc₂O₃ ceramics having an average grain size of ∼9 μm and showing a visible wavelength transmittance of ∼60–62% (∼76% of that of Sc₂O₃ single crystal) have been fabricated via vacuum sintering at a relatively low temperature of 1700°C for 4 h.     

Radiation tolerance of type IIa synthetic diamond detector for 14 MeV neutrons

Radiation tolerance of a type IIa synthetic diamond detector was examined from irradiation of mono-energetic 14 MeV neutrons. Measurements of I–V (current–voltage) characteristics and energy spectrum for 5.486 MeV alpha particles were performed after neutron irradiation. In the I–V characteristics measurement, enhancement of rectification was observed after neutron irradiation of up to 2.0 × 10¹² n/cm². Concurrently with the enhancement of rectification, significant decrease in signal amplitude was observed in energy spectrum measurement for alpha particles. It is considered that these changes were due to increase in the concentration of defects acting as shallow energy levels in the forbidden band. For neutron irradiation of higher than 1.6 × 10¹³ n/cm², weakening of the rectification characteristics and recovery of the signal amplitude were observed. These changes imply that deep energy levels, which were also considered to be introduced by defects, were dominant and weakened the effects of the shallow energy levels. Increase in the concentration of the deep trapping levels resulted in gradual decrease of the signal amplitude and degradation in the energy resolution. The peak for the alpha particles was obtained up to 5.5 × 10¹³ n/cm².     

Osteoinduction by Functionally Graded Apatites of Bovine Origin Loaded with Bone Morphogenetic Protein-2

Bioresorbable and functionally graded apatites (fg-HAp) ceramics, which are characterized by gradations in crystallinity and the grain size of hydroxyapatite (HAp:Ca₁₀(PO₄)₆(OH)₂), were designed using bovine bone by the calcination and partial dissolution–precipitation method. The fg-HAp ceramics had macropores of 100–600 μm originated from spongy bone, and micropores of 10–160 nm. Fg-HAp ceramics loaded with recombinant human bone morphogenetic protein-2 (rhBMP-2/fg-HAp) were implanted into the subcutaneous tissue of rats. Eight weeks after the implantation, the surface and bulk degradations of the fg-HAp-containing body fluid occured, and small pieces of fg-HAp were incorporated into the induced bone and fatty marrow, suggesting that osteoinduction occurred in conjunction with bone remodeling. The rhBMP-2/fg-HAp ceramics developed could become a resorbable biomimetic material with fast bioresorption and osteoinduction characteristics.     

Ozone Generator with Cylindrical Type of Rotating Electrode

An ozone generator using a rotating electrode to improve ozone generation efficiency is proposed. The ozone generator electrode unit consists of a rotating electrode and fixed electrode. The rotating electrode has the grounded 36 pieces of tungsten wires fixed in parallel to the rotation axis on the rotating cylinder surface. A dielectric electrode is used as a fixed electrode located on the inside of the tube of the electrode unit. The width of the apparent discharge gap is 1mm. Alternating current with a frequency of 50 Hz is applied to the electrode unit. The rotation speed can be adjusted from 0 rpm to 1200 rpm by a variable speed motor. Oxygen gas is used as the material gas. Higher ozone concentration and higher ozone generation efficiency are obtained compared with that when the rotation speed is 0 rpm. The gas temperature is measured at the inlet and outlet of the ozone generator, and the rotation speed for the cooling effect is most effective at about 500 rpm. The maximum generation efficiency is estimated to be 61 g/kWh at 800 rpm, and this value is twice as large as in the case of 0 rpm.     

Fabrication of Translucent Magnesium Aluminum Spinel Ceramics

A precursor for magnesium aluminum spinel powder, composed of crystalline ammonium dawsonite hydrate (NH₄Al(OH)₂CO₃·H₂O) and hydrotalcite (Mg₆Al₂(CO₃)(OH)₁₆·4H₂O) phases, was synthesized via precipitation, using ammonium bicarbonate as the precipitant. The precursor was characterized by differential thermal analysis/thermogravimetry, X-ray diffractometry, and scanning electron microscopy. Reactive spinel powder, which could be densified to translucency under vacuum at 1750°C in 2 h without additives, was obtained by calcining the precursor at 1100°C for 2 h.     

Imaging Secondary-Ion Mass Spectroscopy Observation of the Scavenging of Siliceous Film from 8-mol%-Yttria-Stabilized Zirconia by the Addition of Alumina

The scavenging of a resistive siliceous phase via the addition of Al₂O₃ was studied, using imaging secondary-ion mass spectroscopy (SIMS), given the improved grain-boundary conductivity in 8-mol%-yttria-stabilized zirconia (8YSZ). The grain-boundary resistivity in 8YSZ decreased noticeably with the addition of 1 mol% of Al₂O₃. Strong SiO₂ segregation at the grain boundaries was observed in a SIMS map of pure 8YSZ that contained 120 ppm of SiO₂ (by weight). The addition of 1 mol% of Al₂O₃ caused the SiO₂ to gather around the Al₂O₃ particles. The present observations provided direct and visual evidence of SiO₂ segregation at the grain boundaries (which had a deleterious effect on grain-boundary conductivity) and the scavenging of SiO₂ via Al₂O₃ addition.     

Comparison of activities in selective catalytic reduction of NOx by C3H8 over Co/MFI, Fe/MFI, and H/MFI zeolite catalysts

The Co/MFI(SiO₂/Al₂O₃ = 30) were prepared by a precipitation method with NaOCl in alkali solutions exhibited high activities to N₂ at 250 °C for the selective catalytic reduction (SCR) of NO_x. These catalysts showed two UV–vis bands at 700 and 400 nm, indicating the presence of octahedral Co(III) as well as tetrahedral Co(II). The high SCR activity over such Co(III, II)/MFI(30) seems to come from Co(III)---O moieties. The Co(II)MFI(30) catalysts prepared from Co(II)Cl₂ exhibited low SCR activities due to the presence of tetrahedral Co(II) ions in MFI. Less CO formation occurred over Co/MFI catalysts. The Fe/MFI(30) catalyst exhibited high activity due to the presence of some Fe---O species in MFI but more amount of CO were produced during SCR. H/MFI(30) catalyst exhibited a good SCR activity. However, more amount of carbonaceous deposits were produced on it. The correlation between acid concentration and SCR activity was discussed over H/MFIs.     

Formation of carbon nanotubes through ethylene decomposition over supported Pt catalysts and silica-coated Pt catalysts

Ethylene decomposition was performed over supported Pt catalysts to fabricate composites of Pt metal nanoparticles and carbon nanotubes (CNTs). All supported Pt catalysts (Pt/carbon black, Pt/CNT, Pt/MgO, Pt/Al₂O₃ and Pt/SiO₂) showed catalytic activity for ethylene decomposition at 973 K to form CNTs. Pt metal particles were found at tips of CNTs. These results indicate that Pt metal particles have catalytic activity for growth of CNTs through hydrocarbon decomposition. A broad range (5-50 nm) of CNT diameters were formed from the use of supported Pt metal catalysts although Pt metal particles in the catalysts before ethylene decomposition were relatively uniform in size (2-5 nm). These results imply that Pt metal particles in the catalysts aggregated during ethylene decomposition at 973 K. Aggregation of Pt metal particles in catalysts during ethylene decomposition could be suppressed by covering catalysts with silica layers that were a few nanometers thick. Silica-coated Pt catalysts showed high activity for ethylene decomposition to form CNTs with uniform diameters (8-10 nm) despite the uniform coverage of Pt metal particles with silica layers.     

Mechanistic study of the reduction of copper oxides in alkaline solutions by electrochemical impedance spectroscopy

Electrochemical impedance spectroscopy was used to study the mechanism by which copper oxides are reduced in alkaline solutions. For the reductions of CuO and Cu₂O, a capacitive loop and also an inductive loop under certain conditions were observed in the complex plane. The electrochemical impedance for CuO reduction was not greatly dependent on the solution alkalinity and the kind of alkali hydroxide. However, the electrochemical impedance for Cu₂O reduction was considerably affected by the kind and concentration of alkali hydroxide. The diameter of the capacitive loop, i.e., the charge-transfer resistance (R_ct), was increased with increase in solution alkalinity. It should also be noted that R_ct was increased in the order of KOH < NaOH < LiOH. These dependences were consistent with the good separation between the reduction potentials of CuO and Cu₂O in chronopotentiometric and voltammetric measurements with strongly alkaline electrolytes containing Li⁺. The inductive loop observed for the Cu₂O reduction at higher concentrations of KOH (>6 M) and LiOH (>0.2 M) suggested the existence of an intermediate species (probably CuOH). The specific inhibitory effect of Li⁺ ions on the reduction of Cu₂O might be explained by a possible stabilization of CuOH by Li⁺ ions.     

Development of In Vitro and In Vivo Evaluation Systems for Vitamin D Derivatives and Their Application to Drug Discovery

We have developed an in vitro system to easily examine the affinity for vitamin D receptor (VDR) and CYP24A1-mediated metabolism as two methods of assessing vitamin D derivatives. Vitamin D derivatives with high VDR affinity and resistance to CYP24A1-mediated metabolism could be good therapeutic agents. This system can effectively select vitamin D derivatives with these useful properties. We have also developed an in vivo system including a Cyp27b1-gene-deficient rat (a type I rickets model), a Vdr-gene-deficient rat (a type II rickets model), and a rat with a mutant Vdr (R270L) (another type II rickets model) using a genome editing method. For Cyp27b1-gene-deficient and Vdr mutant (R270L) rats, amelioration of rickets symptoms can be used as an index of the efficacy of vitamin D derivatives. Vdr-gene-deficient rats can be used to assess the activities of vitamin D derivatives specialized for actions not mediated by VDR. One of our original vitamin D derivatives, which displays high affinity VDR binding and resistance to CYP24A1-dependent metabolism, has shown good therapeutic effects in Vdr (R270L) rats, although further analysis is needed.