Disturbance-free high-speed sinusoidal phase-modulating laser diode interferometer

A surface profiler that incorporates a feedback controller to eliminate external disturbances is proposed and demonstrated. Its overall performance is dependent on the frequency response of the feedback loop. The frequency of the modulating signal strongly influences the response of the feedback controller. When we used the integrating-bucket method, the CCD camera had to be operated at a low-frequency video rate. Our technique uses a CCD camera equipped with an electronic shutter. The shutter function enables us to apply high-speed sinusoidal phase modulation to the conventional integrating-bucket method under the standard video rate.     

Synchronized fresh cell bioreactor system for continuous L-(+)-lactic acid production using Lactococcus lactis IO-1 in hydrolysed sago starch

An efficient bioreactor, termed a 'synchronized fresh cell bioreactor', was developed and consisted of a pH-dependent substrate feed system coupled with cross flow filtration and turbidity control. The effect of high dilution rate and high cell density coupled with high cell viability on the production of l-lactic acid in continuous culture by Lactococcus lactis IO-1 in enzyme-hydrolysed sago starch medium was investigated. For all changes in dilution rate, cells responded in a synchronized way to the addition of glucose by increasing the rate of biomass formation. Consequently, a glucose-free feed solution was required to maintain the cell concentration at a particular pre-set value. This set-up facilitated the maintenance of the cells in a permanent log phase. At a cell concentration of 15 gl(-1) and a feed glucose concentration of 53 gl(-1), volumetric LA productivities of 8.2, 19.3 and 33.1 gl(-1)h(-1) were obtained at dilution rates of 0.21, 0.50 and 1.1 h(-1), respectively. The respective residual glucose concentrations in the spent medium were 1.90, 0.24 and 3.80 gl(-1). By increasing the cell density, the volumetric productivity increased proportionally. At high cell density, higher dilution rates resulted in lower lactate concentrations in the culture medium resulting in higher productivity. This reactor facilitated efficient operation with high cell viability by maintaining the cells in continuous growth phase for long-term fermentation. Therefore, the growth rate (mu) was calculated according to the Monod equation. Using this system, high specific productivities can be obtained which guarantees high commercial productivity at economical cost with only a small investment for setting up the sago industry.     

Induction of apoptosis in HL-60 cells by skimmed milk digested with a proteolytic enzyme from the yeast Saccharomyces cerevisiae

Bovine skimmed milk digested with cell-free extract of the yeast Saccharomyces cerevisiae was found to exhibit proliferation inhibition activity towards human leukemia (HL-60) cells. The optimum pH for digestion of skimmed milk and production of the proliferation inhibition factor was pH 4.8. Nondigested skimmed milk exhibited little suppressive effect on the proliferation of HL-60 cells. An active enzyme involved in the production of cell proliferation inhibitory materials from skimmed milk was purified from the cell-free extract of S. cerevisiae by a series of column chromatographies: DEAE-Sephacel, D-tryptophan methyl ester-Sepharose 4B, Hiload Superdex G-200 and HPLC Mono Q. The homogeneous purified enzyme and exhibited a molecular mass of 33 kDa in sodium dodeceyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) and was identified as protease B by N-terminal amino acid sequence analysis. Bovine skimmed milk digested with purified protease B was found to inhibit proliferation activity of HL-60 cells most strongly when digestion was conducted at pH 4.8. The cell proliferation inhibition activity induced by digested skimmed milk was shown to be due to the induction of apoptosis, demonstrated by the formation of apoptotic bodies and fragmentation of DNA in treated cells. The proliferation inhibition factors produced were recovered in the soluble fraction of 92% ethanol, suggesting that the factors were hydrophilic low molecular mass substances derived from skimmed milk.     

Heterogeneous pattern of gene expression in cloned cell lines established from a rat transplantable osteosarcoma lung metastatic nodule

We have established three cloned cell lines (COS1NR, COS2NR and COS4NR) from the lung metastatic nodule of a highly metastatic variant of rat transplantable osteosarcoma, C-SLM. All three clones shared the same morphological characteristics and tumorigenicity, but their growth rates in vitro and metastatic ability in vivo differed from each other. Single-strand conformation polymorphism (SSCP) analysis revealed all three clones to have the same p53 gene mutation and parent C-SLM tumor. On the other hand, Northern blot analysis showed a different pattern of expression for the genes, c-fos, c-jun, c-Ha-ras, transin (rat stromelysin), bone Gla protein (osteocalsin) and nm23/NDP kinase. These results indicate the presence of a heterogeneous cell population in terms of the different pattern of gene expression in a lung metastatic nodule of rat osteosarcoma and the present newly established cell lines will be useful for further investigation of the biological behavior of osteosarcomas.     

New modifications of poly(vinyl alcohol)s and their applications

Poly(vinyl alcohol) (PV-OH), prepared from poly(viny) acetate), is used widely in many industries. Various grades have been produced, with different degree of polymerization and degree of hydrolysis. Recently, novel modified (PV-OH)s with anion, cation, silanol or hydrophobic groups have been studied and developed. They have new properties in addition to those of ordinary PV-OH and have new applications. The methods of modification and the characteristics and some applications of the modified polymers are described.     

Elasto-plastic analysis of orthogonally stiffened plates with initial imperfections under uniaxial compression

In general, the stiffened plates consisting of steel plate elements are unavoidably accompanied by initial imperfections such as residual stresses and initial deflections, which have considerable effects on their ultimate strength. Therefore, it is needed for designing them to develop more rational method taking the ultimate strength influenced by initial imperfections into account rather than the conventional design method being on the basis of the linear elastic buckling theory.From this point of view, this study aims to evaluate rigorously the ultimate strength of orthogonally stiffened plate with initial imperfections under uniaxial in-plane compression. The elasto-plastic finite element method is applied to attain this purpose. By a happy combination of modal analytical technique and conventional finite element method, much reduction of the degree of freedom can be expected to be realized herewith. Some numerical calculations are performed by means of this rigorous method to examine the exactness of the analysis. Moreover, the numerical results are compared with the experimental ones.     

Inverse scattering for a three-dimensional object in the time domain

An iterative inverse-scattering approach to reconstruction of electrical parameter distributions of a three-dimensional object by using time-domain field data is presented. The approach is the extension of the forward-backward time-stepping algorithm previously proposed for a two-dimensional object. Numerical examples of simulation data are given to assess the effectiveness of the proposed approach.     

A novel anionic surfactant templating route for synthesizing mesoporous silica with unique structure

Anionic surfactants are used in greater volume than any other surfactants because of their highly potent detergency and low cost of manufacture. However, they have not been used as templates for synthesizing mesoporous silica. Here we show a templating route for preparing mesoporous silicas based on self-assembly of anionic surfactants and inorganic precursors. We use aminosilane or quaternized aminosilane as co-structure-directing agent (CSDA), which is different from previous pathways. The alkoxysilane site of CSDA is co-condensed with inorganic precursors; the ammonium site of CSDA, attached to silicon atoms incorporated into the wall, electrostatically interacts with the anionic surfactants to produce well-ordered anionic-surfactant-templated mesoporous silicas (AMS). These have new structures with periodic modulations as well as two-dimensional hexagonal and lamellar phases. The periodic modulations may be caused by the coexistence of micelles that differ in size or curvature, possibly owing to local chirality. These mesoporous silicas provide a new family of mesoporous materials as well as shedding light on the structural behaviour of anionic surfactants.     

Fabrication of silicon nitride nanoceramics—Powder preparation and sintering: A review

Fine-grained silicon nitride ceramics were investigated mainly for their high-strain-rate plasticity. The preparation and densification of fine silicon nitride powder were reviewed. Commercial sub-micrometer powder was used as raw powder in the “as-received” state and then used after being ground and undergoing classification operation. Chemical vapor deposition and plasma processes were used for fabricating nanopowder because a further reduction in grain size caused by grinding had limitations. More recently, nanopowder has also been obtained by high-energy milling. This process in principle is the same as conventional planetary milling. For densification, primarily hot pressing was performed, although a similar process known as spark plasma sintering (SPS) has also recently been used. One of the advantages of SPS is its high heating rate. The high heating rate is advantageous because it reduces sintering time, achieving densification without grain growth. We prepared silicon nitride nanopowder by high-energy milling and then obtained nanoceramics by densifying the nanopowder by SPS.