A prototype of a superconducting magnet for a 170-GHz gyrotron

Within the framework of the “International Thermonuclear Experimental Reactor” (ITER) program, a prototype of a superconducting magnet for a 170-GHz gyrotron has been developed, manufactured, and tested. The operating induction value (7.1 T at the center of a 219-mm-diameter cold hole and 8.1 T on the winding) is reached at a current of 185.2 A. In the final version of the magnet, the required induction value was reached without aging. Special requirements are imposed on the distribution of the magnetic field along the axis, including an abrupt field decrease on both sides of the magnet. Axial forces are additionally taken by a special device. The magnet’s sections are wound with multifiber conductors based on niobium-tin and niobium-titanium alloys. Seventeen resistive shunts are provided for protecting sections during their transition to the normal state. The magnet is equipped with a device for removing a part of energy from the sections. Mechanical stresses in the magnet’s sections and the structure’s power elements have been measured during tests.     

A device for measuring the equivalent resistance of an energized circuit section

A device for measuring the active resistance of a direct current energized circuit section is described. Owing to the use of up-to-date electronic components, an iteration measurement algorithm, and a sinusoidal signal as a test one, the following performance characteristics have been obtained: the measurement time is <1 s, and the error varies from 0.3 to 2.0% in a 100-Ω to 1-MΩ range and ≤25% in 10-to 100-Ω and 1-to 10-MΩ ranges.     

Miniature in vivo robots for remote and harsh environments

Long-term human space exploration will require contingencies for emergency medical procedures including some capability to perform surgery. The ability to perform minimally invasive surgery (MIS) would be an important capability. The use of small incisions reduces surgical risk, but also eliminates the ability of the surgeon to view and touch the surgical environment directly. Robotic surgery, or telerobotic surgery, may provide emergency surgical care in remote or harsh environments such as space flight, or extremely forward environments such as battlefields. However, because current surgical robots are large and require extensive support personnel, their implementation has remained limited in forward environments, and they would be difficult, or impossible, to use in space flight or on battlefields. This paper presents experimental analysis of miniature fixed-base and mobile in vivo robots to support MIS surgery in remote and harsh environments. The objective is to develop wireless imaging and task-assisting robots that can be placed inside the abdominal cavity during surgery. Such robots will provide surgical task assistance and enable an on-site or remote surgeon to view the surgical environment from multiple angles. This approach is applicable to long-duration space flight, battlefield situations, and for traditional medical centers and other remote surgical locations.     

Diffraction of electromagnetic waves by the boundary of a semi-infinite metamaterial

Diffraction of plane waves at the interface of two semi-infinite regions is considered for the case when one of the regions is filled with a metamaterial in the form of a 3D periodic lattice of dipole-type particles. The diffraction problem is solved via the method of compensating sources, which is extended to the case of 3D structures. Different formulations of the diffraction problem that is reduced to either a system of Wiener-Hopf functional equations or a system of linear algebraic equations are presented. Representation of a semi-infinite structure by a sequence of layers characterized by wave transmission matrices is analyzed. It is shown that such matrices can be used to obtain the solution to the diffraction problem in an explicit form.     

Effect of ultrasonic treatment on photoelectric and luminescent properties of ZnSe crystals

The results of the effect of ultrasonic treatment of ZnSe crystals on the structure of the energy spectrum of electronic states of centers with deep levels forming photoelectric and luminescent properties of this compound are presented. It is for the first time proved experimentally that the climb of edge dislocations under the effect of ultrasound leads to regrouping and generation of defects forming deep levels, which manifest themselves in phenomena of photosensitivity and radiative recombination.     

Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

Effective factors on synthesis of the hematite–silica red inclusion pigment

The work focuses on the synthesis of a red ceramic pigment by inclusion of hematite in a fumed silica matrix with different specific surface areas. Iron(II) sulfate was used as hematite precursor. Mixtures of iron(II) sulfate and fumed silica with different mole ratios were heated at different temperatures from 1000 to 1300 °C for 4 h.     

Radio sensing of a cometary nucleus: Possibilities for investigating the surface layer

The possibility for determining the structure of the surface layer of a cometary nucleus from the data of bistatic radar sensing is investigated. A rigorous solution formulated for this problem on the basis of vector equations of the electromagnetic field is presented.     

Development of Stretch Solder Interconnections for Wafer Level Packaging

A wafer level packaging technique has been developed with an inherent advantage of good solder joint co-planarity suitable for wafer level testing. A suitable weak metallization scheme has also been established for the detachment process. During the fabrication process, the compliancy of the solder joint is enhanced through stretching to achieve a small shape factor. Thermal cycling reliability of these hourglass-shaped, stretch solder interconnections has been found to be considerably better than that of the conventional spherical-shaped solder bumps.     

Xylene Isomerization in a ZSM-5/SS Membrane Reactor

A membrane reactor containing different types of ZSM-5/porous SS membranes was used to perform the xylene isomerization reaction. The parent Na-ZSM-5 layer was synthesized by secondary growth on top of porous stainless steel tubes. The xylene isomerization reaction was carried out at different temperatures in the membrane reactor and in a fixed-bed reactor of identical geometry for comparison. Two different kinds of membranes were prepared by ion exchange: a Pt/H-ZSM-5 catalytic membrane and two Ba-ZSM-5 composites with different Ba²⁺ concentration. The p-xylene production using 100% exchanged Ba-membrane was about 28% higher than the fixed-bed reactor at 370 °C, when m-xylene was fed.