Thickness dependence of H2 gas sensor in amorphous SnQx films prepared by ion-beam sputtering

Amorphous SnO_x films were deposited by ion-beam sputtering on sintered alumina substrates. Amorphous film sensors were prepared by annealing the films at 300° C for 2 h in air. The thickness dependence of resistivity and hydrogen gas sensitivity were measured at 150° C over the thickness range 1 to 700 nm. A resistivity maximum was observed in ultrathin films. Resistivity increased by three orders of magnitude with increasing film thickness from 0.9 to 7.4 nm and then decreased by five orders of magnitude from 7.4 to 35 nm. Ultrathin film sensors showed sensitivity maxima around a thickness of 10 nm. Sensitivity and resistivity of ultrathin films were significantly influenced by the thermal expansion coefficient and the surface state of the substrate.     

Properties of indium oxide/tin oxide multilayered films prepared by ion-beam sputtering

The preparation and characterization of indium oxide (InO _x )/tin oxide (SnO _y ) multilayered films deposited by ion-beam sputtering are described and compared with indium tin oxide (ITO) films. The structure and the optoelectrical properties of the films are studied in relation to the layered structures and the post-deposition annealing. Low-angle X-ray diffraction analysis showed that most films retained the regular layered structures even after annealing at 500° C for 16 h. As an example, we obtained a resistivity of 6×10^–4 cm and a transparency of about 85% in the visible range at a thickness of 110 nm in a multilayered film of InO _x (2.0 nm)/SnO _y (0.2 nm)×50 pairs when annealed at 300° C for 0.5 h in air. Hall coefficient measurements showed that this film had a mobility of 17 cm² V^–1 sec^–1 and a carrier concentration (electron density) of 5×10²⁰ cm^–3.     

Modification of mesophase pitch by blending Part 2 Modification of mesophase pitch fibre precursor with thermoresisting polyphenyleneoxide (PPO)

Polyphenyleneoxide was blended in amounts of 5 or 10 wt% into petroleum-derived mesophase pitch to reinforce the pitch fibre before the oxidative stabilization to achieve better handling properties. Although polyphenyleneoxide was fusible but hardly soluble in the mesophase pitch even at a spinning temperature of 350° C, blended pitch could be smoothly spun into pitch fibre 10m diameter, as could the parent pitch. Fibrous polyphenyleneoxide of less than 1m diameter was homogeneously dispersed in the pitch fibre, being arranged along the fibre axis. Such fibrous polyp henyleneoxide reinforced the pitch fibre considerably. The fibrous substances at the centre of the fibre disappeared in the carbonized fibre at 1300° C after oxidation at 250° C, although some short ones were observed in the skin region of the fibre, suggesting that polyphenyleneoxide was co-carbonized to be assimilated with mesophase pitch at the centre of the fibre, where the effects of oxidation may be rather limited. The oxidation reactivity and its mechanical strength after carbonization were slightly lower in comparison with those of the parent mesophase pitch.     

Synthesis of terpene alcohols from isoprene oligomers

Various terpene alcohols were prepared from isoprene oligomers via two steps: epoxidation with peracetic acid and isomerisation with aluminium triisopropoxide. For example, 2-methylene-6-methyl-7-octene-1-o1 was prepared from 2,6-dimethyl-1,7-octadiene. From 2,6-dimethyl-2,7-octadiene, 3,3,6-trimethyl-1,5-heptadiene, 2,7-dimethyl-2,6-octadiene, 2,6-dimethyl-1,3,6-octatriene, 1-methyl-4-isopropenyl-1-cyclohexene, and 1,5-dimethyl-1,5-cyclooctadiene, the corresponding alcohols were obtained, respectively.     

Development of an anisotropic conductive adhesive film (ACAF) from epoxy resins

A thermoset type anisotropic conductive adhesive film (ACAF), which electrically connects an ITO glass and a flex circuit both having conducting pattersn of less than 100 μm in pitch, has been developed. In this development, bisphenol A and bisphenol F epoxy resins were tested to formulate an ACAF with easy-to-handle tackiness, flexibility, and strenght. A curing agent that gives fast cure and long shelf-life properties to the epoxy resin was also selected. The tensile stress–strain responses of obtained adhesive films were successfully used for determining the formulation. Good aftercure physical properties (electrical and mechanical) were obtained. Durability against high temperature and high humidity were also tested to confirm long-term stability of the conduction of this ACAF. © 1995 John Wiley & Sons, Inc.     

Role of Acetic Acid Added to the Reaction Media for the Enantio-differentiating Hydrogenation of Methyl Acetoacetate Over a Tartaric Acid-modified Nickel Catalyst

The role of acetic acid added to the reaction media for the enantio-differentiating hydrogenation of methyl acetoacetate over a (R,R)-tartaric acid-in-situ-modified nickel catalyst was studied from the viewpoint of the hydrogenation rate during repeated runs. The hydrogenation of methyl acetoacetate on the “enantio-differentiating sites” of a tartaric acid-modified nickel catalyst was specifically accelerated by the acetic acid added to the reaction media to increase the enantio-differentiating ability of the catalyst. In order to increase the enantio-differentiating ability, the addition of acetic acid to the reaction media was required in each run during the repeated use of the catalyst.     

Rapid Quenching Technique Using Thermal-Image Furnace for Glass Preparation

A new technique combining a thermal-image furnace and a twin roller is described for quenching the melt to form glass. The technique was applied to the simple system Li₂O-SiO₂, since its fundamental parameters in the estimation of critical cooling rate are available. Glass flakes were obtained in the composition Li₄SiO₄, for which a very large critical cooling rate (∼10⁹ K·s⁻¹) was needed for glass formation.     

Preparation of modified poly(vinyl chloride) containing N,N-di(β-hydroxyethyl)dithiocarbamate and its reaction with metal ions

Reaction of N,N-di(β-hydroxyethyl)dithiocarbamate ion with poly(vinyl chloride) (PVC) was undertaken, and the reaction with metal ions of the polymer obtained was investigated. The effect of γ-irradiation on the reaction with metal ion was also studied. The modified PVC (PHDC) obtained from the reaction with N,N-di(β-hydroxyethyl)dithiocarbamate ion is pale yellow even after reaction at 100°C for 5 hr in dimethylformamide (DMF); it is soluble in dipolar solvents and its chlorine content is decreased considerably. This polymer reacted well with acetate salts of copper(II), nickel(II), zinc(II), and silver(I) heterogeneously in aqueous solution because of the introduction of hydrophilic groups (two hydroxy groups). The reactivity of the metal ions toward the polymer was of the order Ag(I) ? Cu(II) > Ni(II) > Zn(II). From the result of the reaction of γ-irradiated polymer with cupric ion, the polymer was judged to have fairly good antiradiation property.     

Enantio-differentiating hydrogenation of prochiral ketones over modified nickel

This article reviews the enantio-differentiating hydrogenation of prochiral ketones over a asymmetrically modified catalyst, focusing on the hydrogenation of simple prochiral alkanones. The parameters affecting catalytic activity and enantiodifferentiating ability are considerable in number, and each parameter should be optimized in order to attain a highperformance enantio-differentiating catalyst. Optimization of the parameters and the mode of enantio-differentiation are discussed and compared with the enantio-differentiating hydrogenation of β-ketoesters.     

Surface segregation of siloxane containing component in polysiloxane‐block‐polyimide and s‐BPDA/ODA polyimide blends

Surface segregation in polymer blend systems between 3,3′,4,4′‐biphenyltetracarboxylic dianhydride/4,4′‐diaminodiphenyl ether (s‐BPDA/ODA) polyimide and block copolymer based on polysiloxane‐block‐polyimide (SPI) has been investigated. These polyimide blends, having various compositions of the SPI, were processed by a solution casting method. The glass substrate used in the film‐casting process shows significant effect on the migration of surface segregated species to enrich the air‐exposed surface, whereas the more polar s‐BPDA/ODA tends to remain close to the polar glass substrate. X‐ray photoelectron spectroscopy reveals that even at low SPI concentration, the siloxane moieties in the block copolymer tend to segregate into the air side surface. Contact angle measurement evidently indicates an enrichment of the hydrophobic siloxane fraction on the blend film surface. The average water contact angle of glass side surface is 77°C whereas that of the air side is about 102°C in every blend ratio. This behavior confirms the surface segregation phase separation in these polymer blends. Finally, the surface morphology observed by atomic force microscopy also suggests segregation type of phase separation in these blend systems. POLYM. ENG. SCI., 47:489–498, 2007. © 2007 Society of Plastics Engineers.