Effects of annealing at high pressure on structure and mechanical properties of Al87Ni7Gd6 metallic glass

The effects of annealing and annealing with a superimposed pressure of 940 MPa on the primary crystallization behaviour of α-Al and the resulting micro-hardness have been studied for as-quenched Al₈₇Ni₇Gd₆ metallic glass. Isothermal annealing experiments were conducted for 30 min at 188 °C, 191 °C, and 205 °C in silicone oil maintained either at atmospheric pressure (i.e. 0.1 MPa) or at 940 MPa. XRD analyses detected the evolution of structure with annealing at 0.1 MPa, while specimens annealed with 940 MPa pressure exhibited sharper diffraction peaks than those annealed at 0.1 MPa. DSC measurements were conducted on the as-received amorphous ribbons as well as ribbons annealed at different temperatures at either 0.1. MPa or with 940 MPa superimposed pressure. Specimens annealed with 940 MPa pressure exhibited higher onset temperatures (i.e. T_x1) and temperatures for the first exothermic peak (i.e. T_p1) for primary crystallization. TEM measurements revealed an increase in the volume fraction of α-Al with increases in annealing temperature, while micro-hardness measurements revealed an increase in hardness with increasing amounts of α-Al. Specimens annealed with 940 MPa pressure exhibited further increases in both the volume fraction of α-Al and resulting micro-hardness.     

MECHANISM OF NON-EQUILIBRIUM SEGREGATION OF SOLUTE TO GRAIN BOUNDARIES

本文以空位-溶质原子拖曳机制为基础,并考虑了空位、溶质原子和复合体三者的反应平衡及晶界平衡偏聚的作用,得到了溶质原子的非平衡晶界偏聚动力学方程。对硼在奥氏体中等温及连续冷却时所产生的非平衡晶界偏聚现象进行了理论计算,得到了与实验较为一致的结果。     

用径迹显微照相技术测定Mo对硼在Ni中扩散的影响

本文建立了通过脱硼处理用径迹显微照相技术测量硼在合金中扩散系数的新方法。该法灵敏度高,简捷可靠。实验发现,Ni中加入0.5％Mo对硼的扩散影响不大;而加入3％Mo则有使硼的矿散激活能降低,频率因子减小,在900—1250℃的温度范围内有加快硼扩散的作用。     

Analysis of the correlation between acoustic noise and vibration generated by a multi-layer ceramic capacitor

Acoustic noise generated by a multi-layer ceramic capacitor (MLCC) makes users uncomfortable, so the problem must be analyzed to reduce the noise. There is a correlation between the acoustic noise and the vibration of MLCCs and the circuit board. Therefore, the acoustic noise problem must be investigated from a vibration perspective. In this study, the acoustic noise-generating mechanism was investigated, and the relationship between the characteristics of the noise and the dynamic characteristics of the circuit board with MLCC was analyzed. And a correlation criterion was proposed to predict the acoustic noise using the vibration response of the circuit board.     

Selective Oxidation of Methanol to Formaldehyde Using Modified Iron-Molybdate Catalysts

Methanol selective oxidation to formaldehyde over a modified Fe-Mo catalyst with two different stoichiometric (Mo/Fe atomic ratio = 1.5 and 3.0) was studied experimentally in a fixed bed reactor over a wide range of reaction conditions. The physicochemical characterization of the prepared catalysts provides evidence that Fe₂(MoO₄)₃ is in fact the active phase of the catalyst. The experimental results of conversion of methanol and selectivity towards formaldehyde for various residence times were studied. The results showed that as the residence time increases the yield of formaldehyde decreases. Selectivity of formaldehyde decreases with increase in residence time. This result is attributable to subsequent oxidation of formaldehyde to carbon monoxide due to longer residence time.     

Preparation of nanosize Pt clusters using ion exchange of Pt(NH3) 4 2+ inside mesoporous channel of MCM-41

Mesoporous molecular sieve MCM-41 with a Si/Al ratio of 35 was obtained by hydrothermal synthesis using a gel mixture with a molar composition of 6 SiO₂0.1 Al₂O₃1 hexadecyltrimethylammonium chloride 0.25 dodecyltrimethylammonium bromide 0.25 tetrapropylammonium bromide0.15 (NH₄)₂O1.5 Na₂O300 H₂O. The MCM-41 sample was calcined in O₂ flow at 813 K and subsequently ion exchanged with Ca²⁺. A small Pt cluster has been supported on the MCM-41 sample following a procedure using ion exchange of Pt(NH₃) ₄ ²⁺ . The Pt(NH₃) ₄ ²⁺ ion supported on MCM-41 has been activated in O₂ flow at 593 K and subsequently reduced with Fh flow at 573 K, in the same way used for the preparation of a Pt cluster entrapped inside the supercage of zeolite NaY. The resulting Pt cluster supported on the MCM-41 shows hydrogen chemisorption oftotal two H atoms per Pt at 296 K (based on the total amount of Pt) and high catalytic activity for hydrogenolysis of ethane. The chemical shift in¹²⁹Xe NMR spectroscopy of adsorbed xenon indicates that the Pt cluster is located inside the mesoporous molecular sieve.     

Effects of ion group content and polyol molecular weight on physical properties of HTPB‐based waterborne poly(urethane‐urea)s

A series of waterborne poly(urethane‐urea)s, WPUUs, based on using nonpolar hydroxyl‐terminated polybutadiene (HTPB) as the soft segment, were successfully synthesized in this article. The effects of the COOH group content and soft‐segment molecular weight (Mn_s) on the dispersion, morphology, and physical properties were investigated. Variations of the particle size, viscosity, and zeta potential were first governed by the hydrophilicity of the polymer chain, and then by the swelling derived from water. Fourier transfer infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC) indicated that the degree of phase separation decreased as the COOH group content increased or as Mn_s decreased. However, the hydrogen bonding between the soft and hard segments and the two‐phase mixing could not occur in this nonpolar HTPB‐based WPUU system, indicating that the hard segments tended to form smaller domains and to pack more loosely. It was attributed to the fact that the presence of bulky ionic salt groups destroyed the ordered arrangement of the hard segments. In this case, the increases of the interface area between the soft and hard phases resulted in that the present behaviors were similar to the phase mixing. In tensile properties, HTPB‐based WPUUs exhibited higher tensile stress, elongation at break, and modulus as the COOH group content decreased or as Mn_s decreased. In thermal degradation, the introduction of HTPB polyol improved the thermal stability of WPUU. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Migration of Intergranular Liquid Films and Formation of Core-Shell Grains in Sintered TiC–Ni Bonded to WC–Ni

When TiC–20 wt% Ni powder mixtures are sintered at 1400°C, relatively large TiC grains possibly containing some Ni form with near-equilibrium shapes. When these specimens are heat-treated again at 1400°C in contact with sintered WC–20 wt% Ni pieces, the liquid films between the TiC grains in the contact region migrate against their increasing curvatures, forming (Ti,W)C solid solution behind them. These migrating liquid films reverse their directions on further heat-treatment. As in other alloys, this liquid film migration must be driven by the coherency strain energy produced by W diffusion at the surface of the dissolving TiC grains. Shells of (Ti,W)C solid solution also form around the cores of TiC grains near the contact region, and this process is probably driven by both coherency strain energy and free energy of mixing. At some contact regions, (Ti,W)C precipitates nucleate and grow, probably driven mainly by the free energy of mixing. In powder mixtures, the formation of core-shell grains is expected to be driven by the coherency strain energy, the free energy of mixing, and the capillary effect.     

Modification of a carbon/carbon composite with a thermosetting resin precursor as a matrix by the addition of carbon black

Carbon/carbon composites were made through the pyrolysis of stabilized PAN felt and phenolic resin with the addition of 5 or 10 wt % carbon black to the matrix and then heat treatment at 600–2500°C. The effects of adding carbon black to the matrix precursor on the physical properties, microstructure, and mechanical properties of the resultant composites were investigated. Adding carbon black not only reduced the weight loss but also limited the shrinkage of the resultant composites. Adding carbon black also accelerated the formation of carbon basal planes in the matrix. At 2500°C, the crystalline stacking height in the composite with 10 wt % added carbon black was 200% greater than that with no additive. The flexural strength of the composite also increased from 15 to 42 MPa (almost 300%). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 333–337, 2006     

Influence of continuous stabilization on the physical properties and microstructure of PAN-based carbon fibers

A continuous stabilization and carbonization process was used to prepare polyacrylonitrile (PAN)-based carbon fibers. The stepwise stabilization of PAN fibers was tried at various temperatures. The effect of stepwise stabilization on the physical properties and microstructure of the final carbon fibers is reported in this article. The fixed temperature in stepwise stabilization is kept below the fusion temperature of PAN precursors to avoid overstabilization of the fibers. The optimum stepwise stabilization process not only increases the amount of ladder polymer in stabilized fiber but also improves the physical and mechanical properties of the resultant carbon fibers. The formation of closed pores from open pores in carbon fiber occurs at 1100°C, but the formation of closed pores occurs at 200°C lower for carbon fiber developed from overstabilized fiber. The effect of continuous stepwise stabilization on the properties of resulting stabilized fibers and the variation in physical properties, element composition, and microstructure of carbon fibers during the carbonization process are also reported in this article.