Field Test to Restore Original Geochemical Conditions in a Flooded Mine Area-An Essential Milestone for the Complete Remediation of the Königstein Uranium Mine

Mine Water and the Environment - Uranium was extracted in the Königstein uranium mine by in-situ leaching with sulfuric acid until 1990. The originally anoxic conditions in the ore body became...     

A model for micro-slip between flat surfaces based on deformation of ellipsoidal elastic asperities—parametric study and experimental investigation

Micro-slip is a phenomenon that occurs between contacting surfaces when a frictional load, less than that necessary to produce macro-slip, is applied to the contacting surfaces. A model is evaluated for micro-slip between a flat smooth surface and a flat rough surface. The rough surface is covered with uniformly distributed ellipsoidal elastic asperities. The results from simulations of the model show that anisotropy, material combination and number of contacts of the contacting surfaces influence the tangential stiffness at zero displacement, the length of the micro-slip zone and the energy dissipated in the contact. An experimental investigation verifies the results computed by the model.     

In Situ Mine Water Treatment: Field Experiment at the Flooded Königstein Uranium Mine (Germany)

Within the WISMUT environmental remediation programme, the rehabilitation of the former uranium mine at Königstein is a very special case due to its use of underground leaching and its location near the Elbe River. The mine water is acidic, oxidizing, and polluted with uranium and other contaminants, and must be pumped to the surface and treated. In-situ water treatment approaches have been investigated to optimise further flooding and shorten the period of conventional water treatment. In 2010/2011, a field-scale experiment was carried out: about 120 t of alkalinity were successfully injected into the partially flooded mine. Tracer signals and geochemical reactions achieved general expectations. Based on the results, a site-specific technology concept was developed to flood the mine to its natural decant level.     

Erosion—corrosion characteristics of a 2.25 Cr-1 Mo steel exposed at low particle velocities

The erosion-corrosion characteristics of a 2.25 Cr-1 Mo steel at low particle velocities and elevated temperatures were determined using a nozzle type laboratory erosion tester. The tests were performed with 180–360 μm angular alumina particles at 60° angle of impingement at low particle velocities of 2.6–8.2 m/s and in the temperature interval 20–600°C. The steel was tested both in the as-received condition as well as in two preoxidized conditions. The erosion-corrosion rate of the steel, both in the as-received and in the preoxidized conditions, was found to increase with increasing particle velocity. In contrast, the wastage rates were relatively independent of temperature in the temperature range investigated, the only exception being specimens exposed to the lowest particle velocity (2.6 m/s) at the very highest temperature, i.e. 600°C, which displayed a drastic increase in wastage. Specimens preoxidized at 700°C exhibited a somewhat higher erosion rate compared with non-preoxidized specimens and specimens preoxidized at 500°C. Microscopy revealed four different major wastage mechanisms, i.e. (i) plastic deformation, cracking and micro chipping of surface material of a size corresponding to the area impinged by eroding particles, (ii) chipping of somewhat larger oxide fragments (up to 10–15 μm in diameter), (iii) chipping or spalling of relatively large oxide fragments (up to 30–50 μm in diameter), and (iv) spalling along the steel-oxide interface or within an oxide layer due to cohesive failure, of larger (up to 500 μm in diameter) oxide layer fragments. In the present study extensive spalling was only observed for non-preoxidized specimens exposed to the lowest particle velocity (2.6 m/s) and the two highest specimen temperatures (550°C and 600°C).     

Nuclear microscopy in biomedical analysis with special emphasis on clinical metal biology

Nuclear microscopy based upon developments in high energy ion beam techniques is by now an accepted technique in many fields of research. The advancements into the biomedical field have, however, been slower than expected. A major factor explaining this tendency is the availability of nuclear microscopy. This paper reviews briefly the biomedical work using nuclear microscopy that has been carried out since the 4^th International Conference on Nuclear Microprobe Technology and Applications held in Shanghai. Nuclear microscopy of isolated individual blood cells from patients adversely affected by metal exposure from dental amalgam has been performed both before and after removal of the metallic fillings. The elemental profile of blood cells was more or less normalised after treatment. Some of these results will be presented to illustrate a medical application. Results from bulk analysis by ICP-MS of erythrocytes and plasma before and after treatment will also be presented to illustrate the difference in information content between these two approaches as well as the need for complementary information in solving biomedical problems. As part of a larger study of acute porphyria, nuclear microscopy of blood cells was included among the 78 laboratory tests. The approach in this study was unbiased in the sense that no hypothesis was formulated as to which laboratory parameters would be the most explanatory for health or disease. Multivariate discriminant analysis was applied to the large amounts of data acquired. This approach led to the hypothesis that oxidative stress increased the synthesis of manganese-dependent superoxide dismutase in the mitochondria of polymorphonuclear leukocytes, explaining the increase of manganese in these cells. Antioxidant therapy was therefore applied to a couple of patients with porphyria, however, without clinical success.