Preparation and characterization of chitosan‐based dispersions

Complexation of chitosan in aqueous solutions by low molecular weight electrolytes is one of the simplest methods for the preparation of aqueous chitosan dispersions. In this work, the influence of storage time, sulfate concentration, method of preparation and surfactant content on some properties of the resultant chitosan dispersions (turbidity, viscosity and zeta potential) was analyzed. Turbidimetry was adequate to monitor the formation of particles, while viscometry was suitable to monitor changes in the dispersing phase. An analysis of the properties of these systems, mainly in terms of particle–particle and macromolecule–macromolecule interactions was carried out. Copyright © 2004 Society of Chemical Industry     

Comparison of Lactic Acid Productivities at High Substrate Conversions in a Continuous Two-stage Fermenter With Cell Recycle Using Different Kinetic Models

The steady-state performance of a two-stage recycle fermenter with two different types (I and II) of configurations for staging was investigated numerically for the continuous production of lactic acid. In Type I the bleed broth withdrawn from the first stage is supplied to the second fermenter, and in Type II both filtrate and bleed broth from the first stage are introduced to the second stage. Using four different kinetic models taken from the literature, the effects of operating parameters on the overall lactic acid productivities and the overall substrate conversions are examined. At moderate conversions, productivities for Type I operation are found to be higher than those for Type II and for the single-stage system. In the case of high conversions close to complete consumption, Type II operation is more efficient than the Type I and single-stage systems. For 99% conversion and 40 kg m^-3 substrate feed concentration, productivities for Type II are predicted to be 14-74% higher compared to those for the single-stage system at the same bleed ratios.     

Evaluation of ProKappa

ProKappa is an expert system tool kit developed by IntelliCorp in C using X-Windows for graphical interface. The SUN 3 or 4 version costs $9995/£7000 and $2595/£1800 for the interactive C environment.
This review covers ProKappa version 1.1, installed on a colour SUN SPARC Station 1 with the minimum recommended values of 12 Mb of memory and 30 Mb of swap space.
IntelliCorp can be contacted in the USA at 1975 El Camino Real West, Mountain View, CA 94040-2216 (+1 (415) 965-5500) and in the UK at 10 Jewry Street, Winchester, Hampshire SO23 8RZ (+44 (0)962 735348).     

A fine-grain architecture for relational database aggregationoperations

The design and simulation of a bit-sliced processor for relational database aggregation functions, are discussed. The processor, which addresses an important, computationally expensive problem in database computers, takes two tuples as input (one bit at a time) and returns two bits as output every clock cycle. A larger aggregation unit uses a number of identical slice processors, connected according to odd-even network topology, to achieve improved performance on a parallel pipelined processor. The data processing time is completely overlapped with the input and output of data to and from the unit. The design is independent of the tuple size, and since a bit-serial computation is used, the system requires limited interconnection     

Study of a BGO calorimeter using electron and hadron beams from 1 to 50 GeV

A calorimeter of 25 bismuth germanate (BGO) crystals equipped with silicon photodiode readout has been tested at the CERN SPS in the energy range 1–50 GeV. The response for electrons has been shown to be linear in this energy range and the rms resolution obtained ( ) is approximately 1%, for E > 4 GeV. The electron/pion separation was found to be better than 1:500 in the energy range 1–20 GeV. Data on lateral and longitudinal shower development were compared with the results of a Monte Carlo simulation using the SLAC-EGS program and found to be in good agreement.     

A micromechanical model for cleavage-crack reinitiation

A crack-tip screening analysis of cleavage fracture of steel is developed. The analysis incorporates evidence that reinitiation of an arrested cleavage crack requires less stress intensity than cleavage initiation from a fatigue precrack. Fractographic evidence as well as metallographic sectioning of arrested cracks have previously shown that the mechanism of rapid crack propagation by cleavage is affected strongly by partial crack-plane deflection which leaves unbroken ligaments in its wake. The tearing of these ligaments by dimple rupture is the dominant energy-absorbing mechanism. Earlier etch-pit experiments using an Fe-Si alloy showed that the crack-tip stress intensity based on plastic zone size is extremely low. These observations are incorporated into a model in which cleavage crack reinitiation is analyzed using a sharp crack that is shielded by a distribution of pinching forces along its faces. During reloading of the arrested crack, the ligaments restrict crack-tip blunting, leading to higher local stresses. As a result, lower stress intensities are needed for reinitiation than for initiation from a fatigue precrack.