Application of extended boundary conditions and the Haar wavelets in the analysis of wave scattering by thin screens

A recent approach to solution of 2D scattering problems for electromagnetic waves scattered by thin screens is analyzed. With the use of examples of scattering by a strip and an unclosed cylindrical surface, it is shown that the proposed approach has no advantages in terms of the efficiency of numerical solution over a well-known approach based on exact integral equations for currents that have singular kernels and that are solved with the Krylov-Bogoliubov method.     

Magnetically induced non-Faraday nonreciprocity in a fiber-optic gyroscope

Optical phase nonreciprocity is found to appear in fiber-optic gyroscopes as a result of a magnetically induced distortion of a propagating fiber mode. It is shown that this nonreciprocity places a limitation on the magnetic stability of a gyroscope.     

Finding structure in audio for music information retrieval

This paper presents a brief overview of recent approaches to two problems in music information retrieval: query by example and automated source separation. It describes the challenges inherent in musical query by example and the systems that take very different approaches to the problem. The paper also explores approaches to source separation in a musical context, focusing on systems that take distinct approaches to the problem. Finally, it comments about the future directions for digital signal processing (DSP) research in the context of music information retrieval.     

基于USB总线的虚拟频谱分析仪设计

文章详细介绍了基于USB总线的虚拟频谱分析仪的设计过程。该仪器使用嵌入式混合处理器MC56F8323来实现动态信号的实时采集、频谱分析和数字滤波等功能。处理结果由USB2．0接口芯片CY7C68013上传至PC机．以完成数据显示、存储、绘制图形等功能。其中，CY7C68013工作于Slave FIFO模式，以实现与MC56F8323间的数据传输。该系统可同时对两路动态信号进行实时谱分析，每路采样频率高选500kHz。     

Routing Correlated Data with Fusion Cost in Wireless Sensor Networks

In this paper, we propose a routing algorithm called minimum fusion Steiner tree (MFST) for energy efficient data gathering with aggregation (fusion) in wireless sensor networks. Different from existing schemes, MFST not only optimizes over the data transmission cost, but also incorporates the cost for data fusion, which can be significant for emerging sensor networks with vectorial data and/or security requirements. By employing a randomized algorithm that allows fusion points to be chosen according to the nodes' data amounts, MFST achieves an approximation ratio of 5/4log(k + 1), where k denotes the number of source nodes, to the optimal solution for extremely general system setups, provided that fusion cost and data aggregation are nondecreasing against the total input data. Consequently, in contrast to algorithms that only excel in full or nonaggregation scenarios without considering fusion cost, MFST can thrive in a wide range of applications     

Parametric effects on the transient Voltage performance of a DC superconducting cable

The objective of this work was to determine the significant parameters of a 3-GW 200-kV dc superconducting cable system which influence the transient voltage distribution in the various parts of the cable. The cable system consists of four coaxial metallic cylinders. It was found that the dielectric constant and the electrical resistivity of the soil significantly affect the severity of the transient voltages; lower dielectric constant and higher resistivity of the soil will increase the magnitudes of the transient voltages by increasing the earth-return impedance. It was also found that the effect of the conductor internal impedances of the cable is insignificant. Shorting the coaxial cylinders of the cryogen flow and the cryostat will lessen the severity of the transient voltages. Grounding the second, third, and fourth cylinders at regular intervals with low-impedance grounding impedance will also improve the transient performance of the cable. More research is needed to evaluate these procedures.     

Sigma-delta modulators operating at a limit cycle

A new type of sigma-delta modulator that operates in a special mode named limit-cycle mode (LCM) is proposed. In this mode, most of the SDM building blocks operate at a frequency that is an integer fraction of the applied sampling frequency. That brings several very attractive advantages: a reduction of the required power consumption per converted bandwidth, an immunity to excessive loop delays and to digital-analog converter waveform asymmetry and a higher tolerance to clock imperfections. The LCMs are studied via a graphical application of the describing function theory. A second-order continuous time SDM with 5 MHz conversion bandwidth, 1 GHz sampling frequency and 125 MHz limit-cycle frequency is used as a test case for the evaluation of the performance of the proposed type of modulators. High level and transistor simulations are presented and compared with the traditional SDM designs.     

高导电性原油电脱盐工艺研究

南阳原油中金属含量较高,掺有部分3次采油采出原油,加工时易造成电脱盐装置原油乳化,电导率高,脱盐难度较大。装置投产十几年来脱后含盐一直不合格,经过改造仍然超标,常压塔顶腐蚀严重。为此,对原油进行了电脱盐工艺条件及破乳剂研究,研制出了高效电脱盐设备和生物复合脱盐剂及降电流剂,采用平流弓形电极进行改造,解决了该原油的电脱盐问题,使脱后含盐达到3 mg/L。     

Nonlinear crack dynamics and scaling aspects of fracture (experimental and theoretical study)

Nonlinear dynamics of crack propagation are investigated experimentally and theoretically with the goal of clarifying the nature of limiting crack velocity, the transition from steady state to branching regimes of crack dynamics, and the dynamics of crack arrest. The theoretical explanation of limiting steady-state crack velocity and the transition to a branching regime was proposed due to the study of collective behavior of a microcrack ensemble at the crack tip area. The experimental study of crack dynamics was carried out in a preloaded plate PMMA specimen using the high-speed camera coupled with the photo-elasticity method, the point stress recording with a laser system, and the failure surface roughness measurement.     

EBSP study of the annealing behavior of aluminum deformed by equal channel angular processing

Commercial purity aluminum (99.5%) was fabricated by equal channel angular pressing (ECAP) up to total accumulated strains of approx. 10. The annealing behavior of material deformed to total strains of approx. 1 and 10 was investigated, using heat treatments of 2 h at various temperatures from 100 to 500 °C. The microstructure of the annealed materials was characterized using the electron back-scatter pattern technique. A number of parameters were determined including the distribution and average values of both the boundary spacings and misorientations. For samples deformed to a total strain of 1, annealing resulted in discontinuous recrystallization. For samples deformed to a total strain of 10, annealing resulted in microstructures exhibiting characteristics of both uniform coarsening and, in a number of places, of discontinuous recrystallization. An attempt was made, based on the boundary spacing distributions, to separate these two components. The grain size after annealing was still however small, being just 6.4 μm after 2 h at 300 °C.