A novel way to treat refractory waste: Sonication followed by wet oxidation (SONIWO)

The effectiveness of the hybrid system sonication followed by wet oxidation (SONIWO) to treat otherwise refractory waste has been demonstrated. In such a hybrid system homogeneous CuSO₄ catalyst was found to be very efficient.     

Tunable wavelength filters based on nonlinear optical interactionsin semiconductor amplifiers

A novel class of narrow-band tunable wavelength filters is proposed and evaluated. Wavelength selectivity of the proposed filters Is derived from the finite time response of an optical nonlinearity. The nonlinearity is gain saturation in semiconductor optical amplifier structures. The filters are shown to have very narrow passbands tunable over the entire semiconductor gain bandwidth. The key to filter implementation is a device configuration in which the wave-mixing products can be isolated from the amplified inputs. Three integrated optics compatible configurations are considered and shown to have high filter throughputs 34 to 180% and subangstrom bandwidths     

Cold forging and chemical heat treatment of the casing of the internal joint for VAZ cars

The technological process of cold forging applied for the first time in the production of the casing of the internal joint with races is described. The process operations of cold forging and the annealing and carburizing regimes for this part me described.     

Monitoring systems and determination of actual fatigue usage

At GKN, fatigue monitoring of important components has been conducted since 1979. The monitoring methods depend on the mechanisms of damage; quasi-static loads are regarded as well as dynamic loads. The components were selected for monitoring on the basis of a system analysis. The data resulting from monitoring are used to optimise operation mode steadily. Experience shows that the use of monitoring data as input for fatigue assessment is the most realistic and cost-effective way. This fatigue assessment uses global and local sensitivity studies to evaluate the load-stress relation for each component. These relations can be programmed to produce stress vs. time curves. These are processed according to ASME rules to give a realistic fatigue usage.     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

Increasing the interference immunity of broadband systems for measuring and transmitting information by utilizing nonlinear signal processing methods

A method is considered for increasing the immunity from interference of broadband systems for measuring and transmitting information. It is based on utilizing nonlinear methods to process spread-spectrum signals. The possibility is investigated of using a quasioptimal receiving device which can be implemented in practice. It is shown that the proposed method makes it possible to solve the rejection problem at the physical level. Translated from Izmeritel'naya Tekhnika, No. 11, pp. 13–15, November, 1996.     

Trends in low-cost, high-performance substrate technology

The trends in high density interconnection (HDI) multichip module (MCM) techniques that have the potential to reduce interconnection cost and production time are described. The implementation in laminated dielectric (MCM-L) technology of a workstation processor core illustrates current substrate technology capabilities. The design, routing, layout and thermal management of the processor core are described. Thin-film deposited dielectric (MCM-D) technology is discussed as a cost-effective method for future interconnection applications     

The evolution of custom microarray manufacture

Given the enormous size of the genome and that there are potentially many other types of measurements we need to do to understand it, it has become necessary to pick and choose one's targets to measure because it is still impossible to evaluate the entire genome all at once. What has emerged is a need to have rapidly customizable microarrays. There are two dominant methods to accomplish custom microarray synthesis, Affymetrix-like microarrays manufactured using light projection rather than semiconductor-like masks used by Affymetrix to mass manufacture their GeneChip/sup TM/ arrays now, or the ink-jet printing method employed by Agilent. The manufacture of these custom Affymetrix-like microarrays can now be done on a digital optical chemistry (DOC) machine developed at the University of Texas Southwestern Medical Center, and this method offers much higher feature numbers and feature density than is possible with ink-jet printed arrays. On a microarray, each feature contains a single genetic measurement. The initial DOC prototype has been described in several publications, but that has now led to a second-generation machine. This machine reliably produces a number of arrays daily, has been deployed against a number of biomedical questions, is being used in new ways and has also led to a number of spin-off technologies.     

Experience in High-Temperature Thermomechanical Treatment with Helical Reduction in the Production of Axisymmetric Parts

Metal Science and Heat Treatment -