Modified Indigo Method For Gaseous And Aqueous Ozone Analyses

The indigo method developed by Bader and Hoigné for aqueous ozone analysis was modified to allow for both gaseous and aqueous ozone determination. Gas or water samples were extracted with a gas-tight syringe containing a known volume of indigo reagent. The modified procedure provided a more consistent basis for gaseous and aqueous ozone determination allowing for more accurate ozone mass balance calculations. Direct gaseous ozone UV absorbance with molar absorptivity of 3,000 M^?1cm^?1 at 258 nm was used as primary standard to determine the molar absorptivity of the indigo reagent. The molar absorptivity of indigo reagent, assuming a 1:1 stoichiometric ratio for the reaction between indigo and ozone, was determined to be 23,150 ± 80 M^?1cm^?1, or approximately 16 percent higher than that of 20,000 M^?1cm^?1 suggested by Bader and Hoigné. An independently calibrated membrane-electrode ozone monitor showed good correlation with indigo method results using the molar absorptivity value determined in this study. The apparent molar absorptivity of aqueous ozone at the wavelength of 258 nm measured by the modified indigo method increased from 2,400 to 3,600 M^?1cm^?1 in the investigated ozone concentration range of 0.4 to 11.0 mg/L. This variation might have been caused by the inherent interference of unidentified ozone byproducts, which presence was supported with scanning spectra in the wavelength range of 200 to 300 nm.     

Influence of processing on ethylene propylene block copolymers (II): Fracture behavior

The present work investigates the relationships between the microstructural state and fracture properties in commercial polypropylene‐based materials. In this case an isopolypropylene homopolymer and three ethylene propylene block copolymers (EPBC) with different ethylene content (EC) have been studied. A variety of morphologies were obtained by a combination of several processing methods (injection molding, injection molding‐annealing, and compression molding) and thickness. Fracture behavior of deeply double‐edged notched specimens was evaluated by scanning electron microscopy (SEM) and by the essential work of fracture (EWF) method, analyzing the influence of processing, thickness (t), EC, and orientation respect to melt flow direction (MD and TD). The testing direction and EC are the most relevant variables that affect the ability of the crack tip to deform plastically during the crack propagation, determining the final fracture behavior. The fracture parameters obtained with the EWF method, specific EWF, w_e, and plastic item, βw_p, have proved to be very sensitive to the processing induced morphology, finding interesting relationships between such morphologies (characterized by crystallinity index, orientation level, and skin/core ratio) and the fracture parameters of the plaques. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2714–2724, 2006     

Nutritional recovery of mild and moderately malnourished children under two different treatment approaches (ambulatory versus day-care)

This retrospective analysis was conducted between May 1997 and May 2000 at the Centro de Atención Nutricional Infantil de Antímano, CANIA, in Caracas, Venezuela to assess the efficacy of two treatments (ambulatory versus day-care) of mild and moderate malnourished children. Inclusion criteria were: children under 10 years old with mild and moderate malnourishment, who attended a minimum of 3 control visits during a period of 12 months. One hundred fourteen malnourished children were included: fifty seven in ambulatory treatment and fifty seven in day-care treatment paired per nutritional diagnosis, gender and age (thirty nine mild and eighteen moderate malnourished children). The nutritional recovery criterion was weight for height above tenth percentile. No relation was found between treatment approaches and nutritional recovery at 3 and 6 months of treatment. In the group of mild malnourished children, the percentage of recovered patients at 3 months of treatment, that kept their recovered condition at 6 months was 83% (15/18) in the ambulatory treatment and 82% (18/22) in the day-care treatment Age of children, associated disease, acute morbidity, dietetic risk and mother's education and age were not associated with nutritional recovery at 6 months of treatment (p > 0.05). The day-care approach resulted as effective as ambulatory in mild malnourished children. In moderate malnourished new studies will need to be conducted with greater number of patients.     

Inactivation of Fusarium oxysporum Conidia in Soil with Gaseous Ozone – Preliminary Studies

ABSTRACT

In this study, the efficiency of gaseous ozone (O₃) injected in the soil as an oxidizing agent for the inactivation of F. oxysporum was evaluated under laboratory conditions. The results show the treatment reached an inactivation efficiency of 76% after an applied dose of 0.40 g O₃ kg ^?1 soil. This shows that the injection of O₃ can be a viable alternative to control pathogenic organisms in the soils. Nevertheless, it is clear that more studies on determining the effects of this treatment on soil quality are needed.     

Modèles Hydrodynamiques pour la Séparation des Courants dans un Décanteur Pilote

Despite of its general use in industry, particle sedimentation is still a not well understood unit operation. Hydrodynamics is complex in essence, mainly because the possible volumes are depending on the operating conditions, which in turn has consequences on the stability of the equipment in unsteady state conditions.     

Crystallization of hydrogenated sunflower-cottonseed oil

Crystal structures formed during solidification of hydrogenated cottonseed oil, sunflowerseed oil and their blends were analyzed by using an X-ray diffraction technique, differential scanning calorimetry (DSC) and polarized light microscopy. Temperatures and times of crystallization under conditions which tend to produce β′ type structures were determined in terms of refrigeration parameters. Microscopy with polarized light also helped clarify some aspects of the tridimensional network of crystals that contribute to the consistency of products made from hydrogenated oils.     

Effects of the blending sequence and interfacial agent on the morphology and mechanical properties of injection molded PC/PP Blends

Summary The effects of blending sequence and the addition of an interfacial agent (triblock copolymer styrene-butylene ethylene/styrene, Kraton G1652) on the morphology and the mechanical properties of Polycarbonate (PC)/Polypropylene (PP) blends prepared by injection molding were studied. This study presents an analysis of impact resistance, tensile properties and morphology of the raw materials and the blends at different compositions. The blends, before being injected, were prepared in a twin-screw extruder by different sequences of blending. The results indicate that the blending sequence and the presence of humidity significantly affect the properties and morphology of the blends. For ternary blends (PC/PP/Kraton), only one-step mixing before injection molding proved to be sufficient to improve mechanical properties. Increasing the amount of blending steps did not present a significant change in properties. With the addition of the interfacial agent, higher impact resistance and particle size reduction were observed.     

New sesquiterpenes fromMaytenus species (Celastraceae). Taxonomic and chemotaxonomic considerations concerning chileanMaytenus

Three new dihydro--agarofuran sesquiterpenes from two species ofMaytenus were isolated and their structures were elucidated by means of¹H and¹³C NMR studies. The differences and similarities noted in the chemical content of the dihydro--agarofuran sesquiterpenes from the fourMaytenus species from Chile are in line with the taxonomic characterization of these species; their geographical distribution is also given.     

Field Evaluation of Plant Odor and Pheromonal Combinations for Attracting Plum Curculios

The attractiveness of different synthetic host odors and a synthetic aggregation pheromone (grandisoic acid [GA]) to overwintered adult plum curculios (PCs), Conotrachelus nenuphar (Herbst) (Coleoptera: Curculionidae), was examined using two types of traps (sticky panels and black pyramids) placed in border areas surrounding an unsprayed section of an apple orchard in Massachusetts. In 2001, we evaluated the response of PCs to three synthetic fruit volatiles (benzaldehyde [BEN], ethyl isovalerate [EIV], and limonene [LIM]) assessed alone and in combination with GA, as well as the response to GA alone and a no-odor (control) treatment. BEN was the only host volatile that synergized the response of PCs to GA for both trap types. For both trap types, GA was as attractive to PCs as a single component as when in combination with either EIV or LIM. In 2002, four release rates of BEN (0, 2.5, 10, and 40 mg/day) and two release rates of GA (1 and 2 mg/day) were evaluated for attractiveness to PCs using panel and pyramid traps. For panel traps, an increase in amount of GA released (from 1 to 2 mg/day) was associated with a 35% increase in captures. However, PC captures by pyramid traps were similar regardless of the amount of GA released. For panel traps, 10 and 40 mg/day of BEN were the most attractive release rates regardless of the amount of GA released. For pyramid traps baited with GA. PC captures were enhanced by the presence of BEN, regardless of release rate. In 2003, GA at 1 mg/day + BEN at 80 mg/day of release did not enhance PC captures by panel traps relative to lower release rates of BEN. Pyramid traps releasing GA at 1 mg/day performed best when baited with BEN at 10 mg/day of release; a release rate of 80 mg/day of BEN decreased the attractiveness of the binary combination of BEN + GA. Combined results suggest that BEN at 10 mg/day + GA at 1 mg/day of release constitutes an attractive lure that may improve the effectiveness of monitoring traps for PCs.     

A color image watermarking framework for copyright protection of stereo images based on binocular just noticeable difference and LU decomposition

Multimedia Tools and Applications - The copyright protection of three-dimensional (3D) content is a matter of interest in artistic and creative works due to the rights of the holder for the...