Relay-Assisted Wireless Energy Transfer for Efficient Spectrum Sharing in Harsh Environments

International Journal of Wireless Information Networks - With exponential growth in the number of wireless devices and limited available spectrum, the problem of spectrum sharing remains in...     

WSANFlow: An Interface Protocol Between SDN Controller and End Devices for SDN-Oriented WSAN

When dealing with a Wireless Sensor and Actuator Network (WSAN) structure, one of the challenging problems is lack of flexibility in such network operations as establishment, management, and configuration. Software-defined Networking (SDN) is a promising technology for a simpler, more flexible, and less overworked network structure. Integration of SDN as a solution into the existing WSAN structures seems to be a strong candidate of deployment solutions for next generation WSAN systems. In order to get enhanced performance results for WSAN systems, we proposed an interface protocol, referred to as WSANFlow, which is responsible for all the communications between SDN controller (SDNC) and SDN-oriented end devices. The SDNC in this approach has the network intelligence and is capable of handling all the control and management operations related to the network. Thus, advanced communication operations can be managed and efficiently optimized efficiently by the SDN controller and then, subsequently, corresponding instructions can be delivered to end devices using the proposed WSANFlow protocol. In the study, we analyzed the proposed framework performance, in terms of power consumption ratio, throughput, and end to end delay metrics. Then, we compared the results with those of a ZigBee-based counterpart for different workloads such as; light, heavy and heavier load which modelizes a video stream of mild parameters. The results show that not only has the overall performance of the existing WSAN system been enhanced, but also control and management operations have been simplified by the proposed model.     

Interference Mitigation Based on Radio Aware Channel Assignment for Wireless Mesh Networks

An intricate network deployment for high demand users leads to simultaneous transmission in wireless mesh networks. Multiple radios are adapted to individual nodes for improving network performance and Quality of Service (QoS). However, whenever multiple radios are assigned to the same channel, co-located radio interference occurs, which poses a major drawback. This paper proposes a Radio aware Channel Assignment (Ra-CA) mechanism based on a direct graphical model for mitigation of interference in multi-radio multi-channel networks. Initially, the co-located radio interference is identified by classifying non-interfering links for simultaneous transmission in the network. Proposed channel assignment mechanism helps in allocating the minimal number of channels to the network that mitigate co-located radio interference. Performance analysis of the proposed Ra-CA strategy is carried out compared with other existing techniques, like Breadth First Search-Channel Assignment (BFS-CA) and Maximal Independent Set Channel Assignment (MaIS-CA), in multi-radio networks. Simulation results demonstrate that the proposed channel assignment scheme is more efficient compared to the existing ones, in terms of QoS parameters like, packet drop rate, packet delivery ratio, transmission delay and throughput.     

A Bayer pattern-based fragile watermarking scheme for color image tamper detection and restoration

Multidimensional Systems and Signal Processing - The security of multimedia documents becomes an urgent need, especially with the increasing image falsifications provided by the easy access and use...     

Compact and High Speed Architectures of KASUMI Block Cipher

Wireless Personal Communications - This paper proposes highly compact and high speed hardware architectures of 64-bit KASUMI block cipher for wide range of wireless applications. A novel...     

RAPID PYROLYSIS OF EASTERN CANADIAN COALS BY FREE FALL REACTORS

The effect of temperature was investigated on the rapid pyrolysis of Prince, Lingan and No. 26 coals in the temperature range of 525^° to 750^°C using a 600 cm high stainless-steel free fall reactor at atmospheric pressure.

The yields of char, condensibles and gaseous products were determined at 25^°C intervals. Gaseous products were analysed for H₂, CO, CO₂, CH₄ and C₂+.

Volatile product (condensible and gas) yields exceeded the volatile product in the A.S.T.M. methods at and above 700^°C.

Some experiments using Prince coal were repeated at reduced pressure (50 mm mercury) in both the 600 cm height stainless-steel and a 140 cm height quartz reactor in order to find out the effect of pressure and retention time.

The experimental results indicated that the condensable yield was higher at the lower pressure and at the shorter retention time. The effect of retention time was far more pronounced.     

SOLVENT EXTRACTION OF PAKISTANI COALS (ii): EXTRACTION AND CHARACTERIZATION OF METHANOL-BENZENE EXTRACTS

Structural characterization of the solvent extracts from four different Pakistani lignitic coals has been carried out by their proximate, elemental analysis and FT-Infrared and ¹H n.m.r. spectra. The yield of each extracts was greater with 1:1 benzene-methanol mixture in comparison to the total yield obtained by separate extractions with benzene and methanol. The extracts contained significantly less amount of ash and fixed carbon along with an increase in the percentage of volatile matter. The FTIR and ¹H n.m.r. spectra indicated that basically all the extracts contained less condensed aromatic rings in comparison to the coal. The FTIR spectra showed sharp well resolved peaks which have been assigned to various functional groups.

The ¹H n.m.r. spectra were used to obtain average structural parameters for all the extracts. A detailed analysis of the FTIR and n.m.r. spectra of the coal and their extracts provided an important in-sight into the differences between various extracts and also between various coals and their corresponding extracts.     

Hybrid Organic/Inorganic Nanostructures for Highly Sensitive Photoelectrochemical Detection of Dissolved Oxygen in Aqueous Media

Precise, reliable, and remote measurement of dissolved oxygen in aqueous media is of great importance for many industrial, environmental, and biological applications. In particular, photoelectrochemical sensors working in differential mode have recently demonstrated promising properties, in terms of stability, sensitivity, and application potential. Here, a new approach is presented, combining visible light sensitivity, efficient photocurrent generation, and solution‐processed fabrication methods of conjugated polymers, with charge carriers selectivity, energetic alignment favorable to efficient interfacial charge transfer and high surface area achievable by using metal oxide nanostructures. Extensive characterization and optimization of the hybrid organic/inorganic system are carried out, leading to the realization of an oxygen sensor device, based on nanostructured palladium oxide/poly[(9,9‐dioctylfluorenyl‐2,7‐diyl)‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole]/[6,6]phenyl‐C61‐butyric acid methyl ester (PdO/APFO‐3:PCBM) as materials of choice. State‐of‐the‐art sensitivity, amounting at ?5.87 μA cm^?2 ppm^?1, low background signal, in the order of ?4.85 μA cm^?2, good electrochemical stability for more than 2 h of continuous functioning and high reproducibility of the signal over the pH 1 to 10 range, are reported, making the hybrid device suitable for several practical uses. The results fully validate the mixed organic/inorganic approach for photoelectrochemical applications, and pave the way for its further exploitation in fields like waste water treatment, environmental monitoring, and water splitting.     

FPGA Based Implementation and Comparison of Beamformers for CDMA2000

For the integration of smart antennas into third generation code division multiple access (CDMA) base stations, it still remains as a challenging task to implement smart antenna algorithms on programmable processors. In this paper, we study implementations of some CDMA compatible beamforming algorithms, namely least mean square (LMS), constant modulus (CM), and space code correlator (SCC) algorithms, using Xilinx??s Virtex family FPGAs. This study exhibits feasibility of implementing even simple, practical, and computationally small algorithms based on today??s most powerful FPGA technologies. 16 and 32 bits floating point implementations of the algorithms are investigated using both Virtex II and Virtex IV FPGAs. CDMA2000 reverse link baseband signal format is used in the signal modeling. Randomly changing fading and Direction-of-arrivals (DOAs) of multipaths are considered as a channel condition. The implementation results in terms of beamforming accuracy, FPGA resource utilization, weight vector computation time, and DOA estimation error are presented. Beamformer weight vectors using LMS and CM can be computed within less than 20 ??s on Virtex II FPGA and 10 ??s on Virtex IV FPGA, and using SCC it can be achieved within less than 22 ??s on Virtex IV FPGA. These results show that FPGAs provide approximately 500 times faster speed in implementations than our previous work with DSPs.