Fabrication of platinum nanoparticle counter electrode for highly efficient dye-sensitized solar cells by controlled thermal reduction time

We report the effect of the thermal reduction time during sintering on the electrocatalytic activity and the morphology of platinum nanoparticles (Pt-NPs) fabricated using thermal decomposition method. A uniform and dense distribution of Pt-NPs on fluorine-doped tin oxide glass substrate was achieved by controlling the thermal reduction time higher than 15 min and this morphology of Pt-NPs was responded for high electrocatalytic performance of counter electrode (CE). As expected, the excellent electrocatalytic activity with low charge-transfer resistance of 1.04 Ω cm² and highly conductivity of Pt-NPs CE prepared at the thermal reduction time of 15 min during sintering was obtained, which was desirable for dye-sensitized solar cells. The energy conversion efficiency of 9.43 % was obtained for the thermal reduction time of 15 min with fill factor of 63.05 %, J _sc of 18.82 mA cm^?2 and V _oc of 795 mV.     

Photocrosslinking of functionalized rubbers. X. Butadiene–acrylonitrile copolymers

The photocrosslinking of polyacrylonitrile‐block‐polybutadiene‐block‐polyacrylonitrile (ABA) was shown to proceed within seconds at ambient temperature upon UV exposure in the presence of an acylphosphine oxide photoinitiator. The curing process was followed by infrared spectroscopy, insolubilization, and hardness measurements. Complete insolubilization could not be achieved with the neat ABA rubber because of the poor reactivity of the 2‐butene double bond and the low vinyl content of the polybutadiene chain. The addition of multifunctional acrylate monomers (20 wt %) causes a substantial increase of both the reaction rate and the crosslink density of the polymer, which becomes completely insoluble in toluene in less than 1 s upon UV irradiation. An even greater effect was observed by using small amounts (1 wt %) of a trifunctional thiol crosslinker. Both the thiol and the photoinitiator concentrations were shown to affect the kinetics of the thiol–ene polymerization and the polymer network crosslink density. A direct relationship was found to exist between the swelling degree of the UV‐cured rubber and the interchain molecular weight of the network. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2204–2216, 2001     

接触面陷阱密度对a-InSnZnO薄膜晶体管器件电气性能的影响研究

We reported the influence of interface trap density（Nt） on the electrical properties of amorphous InSnZnO based thin-film transistors,which were fabricated at different direct-current（DC） magnetron sputtering powers.The device with the smallest N_t of 5.68×10¹¹ cm^-2 and low resistivity of 1.21×10^-3Ω·cm exhibited a turn-on voltage(V_ON) of-3.60 V,a sub-threshold swing（S.S） of 0.16 V/dec and an on-off ratio(I_ON/I_OFF) of⁸ x 108.With increasing N_t,the V_ON,S.S and I_ON/I_OFF were suppressed to-9.40 V,0.24 V/dec and 2.59×10⁸,respectively.The V_TH shift under negative gate bias stress has also been estimated to investigate the electrical stability of the devices.The result showed that the reduction in N_t contributes to an improvement in the electrical properties and stability.     

Cognitive amplify‐and‐forward relay networks with beamforming under primary user power constraint over Nakagami‐m fading channels

In this paper, we analyze the performance of cognitive amplify‐and‐forward (AF) relay networks with beamforming under the peak interference power constraint of the primary user (PU). We focus on the scenario that beamforming is applied at the multi‐antenna secondary transmitter and receiver. Also, the secondary relay network operates in channel state information‐assisted AF mode, and the signals undergo independent Nakagami‐m fading. In particular, closed‐form expressions for the outage probability and symbol error rate (SER) of the considered network over Nakagami‐m fading are presented. More importantly, asymptotic closed‐form expressions for the outage probability and SER are derived. These tractable closed‐form expressions for the network performance readily enable us to evaluate and examine the impact of network parameters on the system performance. Specifically, the impact of the number of antennas, the fading severity parameters, the channel mean powers, and the peak interference power is addressed. The asymptotic analysis manifests that the peak interference power constraint imposed on the secondary relay network has no effect on the diversity gain. However, the coding gain is affected by the fading parameters of the links from the primary receiver to the secondary relay network. Copyright © 2012 John Wiley & Sons, Ltd.     

Effect of temperature on the electrochemical oxidation of ash free coal and carbon in a direct carbon fuel cell

The present study proposes the application of ash-free coal (AFC) as a primary fuel in a direct carbon fuel cell (DCFC) based on a molten carbonate fuel cell (MCFC). AFC was produced by solvent extraction using microwave irradiation. The influence of AFC-to-carbonate ratio (3: 3, 3: 1, 3: 0 and 1: 3 g/g) on the DCFC performance at different temperatures (650, 750 and 850 oC) was systematically investigated with a coin-type cell. The performance of AFC was also compared with carbon and conventional hydrogen fuels. AFC without carbonate (AFC-to-carbonate ratio=3: 0 g/g) gave a comparable performance to other compositions, indicating that the gasification of AFC readily occurred without a carbonate catalyst at 850 oC. The ease of gasification of AFC led to a much higher performance than for carbon fuel, even at 650 oC, where carbon cannot be gasified with a carbonate catalyst.     

Electrical characterization of individual metal‐coated polymer spheres used in isotropic conductive adhesives

Isotropic conductive adhesives (ICAs) filled with metal‐coated polymer spheres (MPS) have been proposed to improve the mechanical reliability compared to conventional ICAs filled with silver flakes. The electrical properties of MPS play an important role in the electrical performance of macroscopic MPS‐based ICAs. This article deals with the electrical characterization of individual MPS using a nanoindentation‐based flat punch method, in which the resistance and the deformation of single MPS were monitored simultaneously. Four groups of silver‐coated polymer spheres (AgPS) with identical polymer cores but different silver coating thicknesses were tested. The resistance of AgPS decreases gradually with increasing deformation degree of particles, and increases when the deformation of particles is reduced. In addition, the resistance of individual AgPS is dependent on the physical properties of the silver coating, such as thickness, uniformity, and porosity. The thicker the silver coating is, the lower and more stable the resistance of AgPS is. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43764.     

Comparative Study of Ultrasonication-Induced and Naturally Self-Assembled Silk Fibroin-Wool Keratin Hydrogel Biomaterials

This study reports the formation of biocompatible hydrogels using protein polymers from natural silk cocoon fibroins and sheep wool keratins. Silk fibroin protein contains β-sheet secondary structures, allowing for the formation of physical cross-linkers in the hydrogels. Comparative studies were performed on two groups of samples. In the first group, ultrasonication was used to induce a quick gelation of a protein aqueous solution, enhancing the ability of Bombyx mori silk fibroin chains to quickly entrap the wool keratin protein molecules homogenously. In the second group, silk/keratin mixtures were left at room temperature for days, resulting in naturally-assembled gelled solutions. It was found that silk/wool blended solutions can form hydrogels at different mixing ratios, with perfectly interconnected gel structure when the wool content was less than 30 weight percent (wt %) for the first group (ultrasonication), and 10 wt % for the second group (natural gel). Differential scanning calorimetry (DSC) and temperature modulated DSC (TMDSC) were used to confirm that the fibroin/keratin hydrogel system was well-blended without phase separation. Fourier transform infrared spectroscopy (FTIR) was used to investigate the secondary structures of blended protein gels. It was found that intermolecular β-sheet contents significantly increase as the system contains more silk for both groups of samples, resulting in stable crystalline cross-linkers in the blended hydrogel structures. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used to analyze the samples’ characteristic morphology on both micro- and nanoscales, which showed that ultrasonic waves can significantly enhance the cross-linker formation and avoid phase separation between silk and keratin molecules in the blended systems. With the ability to form cross-linkages non-chemically, these silk/wool hydrogels may be economically useful for various biomedical applications, thanks to the good biocompatibility of protein molecules and the various characteristics of hydrogel systems.     

Highly sensitive electrochemical sensor based on zirconium oxide-decorated gold nanoflakes nanocomposite 2,4-dichlorophenol detection

Journal of Applied Electrochemistry - In this study, a sensitive and selective electrochemical sensor based on a zirconia oxide-decorated gold nanoflake nanocomposite-modified glassy carbon...     

Shear‐induced shish‐kebab structures in isotactic polypropylene using acicular precipitated calcium carbonate as whisker

It has been reported in the technical literature that whiskers of rodlike single crystals can be used in order to generate shish‐kebab structures or other different lamellae morphologies during isothermal or dynamic crystallization of sheared or presheared polymer melts. The expected advantage of the changed crystalline structure is a reinforcing effect of the composite. A lot of papers reported about the application of inorganic and organic whiskers such as cellulose and chitin whiskers. This study reports on an attempt to use acicular PCC as appropriate whisker for improving mechanical properties of polypropylene. In this article special attention is given to demonstrate the effect of flow induced crystallization under varying shear conditions in order to improve the mechanical properties. The effects were demonstrated using rheology, thermal analysis, tensile testing, and transmission electron microscopy. POLYM. ENG. SCI., 54:2057–2063, 2014. © 2013 Society of Plastics Engineers