On the Feasibility of Growing Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 Single Crystals

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by two methods: from solution using PbO as a self‐fluxing agent (SC method) and directly from the melt without fluxing (MC method). In both growth methods, an allomeric Pb[(Mg_1/3‐Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal was used as a seed. X‐ray diffraction patterns of ground crystals showed that phase‐pure perovskite PZNT91/9 single crystals were successfully fabricated by the above two methods. The composition of the crystals obtained by both the SC and MC methods was analyzed using X‐ray fluorescence, which confirmed that the crystal composition is close to the nominal value, although volatilization of PbO and segregation during crystal growth are inevitable. The MC PZNT91/9 crystals exhibit excellent piezoelectric properties, with the piezoelectric constant, d₃₃, in the range of 1800–2200 pC N^–1. This value is comparable to that of the SC crystals. However, the MC crystals show an abnormal dielectric behavior. In contrast with the SC crystals, in the MC crystals a much broader dielectric peak appears in the dielectric response curves, accompanied by a much lower peak temperature of around 105 °C. Furthermore, frequency dispersion is apparent over a much wider temperature range (even more apparent than in pure relaxors), where a large, i.e., about 70 °C, full width at half maximum (FWHM) for the dielectric peaks is observed in the dielectric response. It is speculated that such an unusual phenomenon correlates with defects, microinhomogeneities, and polar regions in the as‐grown MC crystals. The origins of this abnormality have not been interpreted in detail until now. However, optical observation of the domain structure confirms that both the SC and MC crystals possess complex structural states.     

Measurements of small-scale fading and path loss for long range RF tags

RF modulated backscatter (RFMB), also known as modulated radar cross section or sigma modulation, is a RF transmission technique useful for short-range, low-data-rate applications, such as nonstop toll collection, electronic shelf tags, freight container identification and chassis identification in automobile manufacturing, that are constrained to have extremely low power requirements. The small-scale fading observed on the backscattered signal has deeper fades than the signal from a traditional one-way link of the same range in the same environment because the fading on the backscattered signal is the product of the fading on the off-board-generated carrier times the fading on the reflected signal. This paper considers the continuous wave (CW) type of RFMB, in which the interrogator transmitter and receiver antennas are different. This two-way link also doubles the path loss exponent of the one-way link. This paper presents the cumulative distribution functions for the measured small-scale fading and the measured path loss for short ranges in an indoor environment at 2.4 GHz over this type of link.     

Catalytic aminolysis of epoxide by alumina prepared from amine-protected Al precursor

The catalytic activities of alumina prepared from an Al alkoxide-amine adduct monomer for the reaction of cyclopentene oxide with piperidine was determined after various pretreatments, including calcination and exposure to moisture. They were compared with the activity of alumina prepared by the conventional hydrolysis method. It was found that the as-prepared sample from the alkoxide-amine monomer preparation was five times more active than a conventional preparation, suggesting that it has a higher density of surface Lewis acid sites. However, its activity was much more severely suppressed by exposure to moisture.     

A decision support system for interactive decision making - Part II: analysis and output interpretation

For pt.I see ibid., p.42-55 (2003). The development of a comprehensive decision support system, GMCR II, for the systematic study of real-world interactive decision problems is presented. The companion paper (Part I), discusses how GMCR II elicits, stores, and manages conflict models; here (Part II), the focus is on GMCR IIs analysis and output interpretation subsystems. Specifically, this paper describes the powerful and efficient analysis engine contained in GMCR II, its informative output presentation and interpretation facilities, and a number of follow-up analyses. Furthermore, an illustrative case study is used to demonstrate how GMCR II can be conveniently applied in practice.     

Techniques for high-frequency integrated test and measurement

This paper describes techniques for the on-chip measurement of high-frequency and/or high-bandwidth electrical phenomena in ultra large-scale integration environments. The techniques rely on the integration of multiple compact and robust electronic test devices, or cores, at various locations within an integrated circuit. The cores consist primarily of signal generators that approximate the output of a sigma-delta modulator using finite repetitious bit patterns and a small set of highly robust analog components. They are capable of digitizing on-chip signals at gigahertz rates even using low-cost manufacturing processes. Simple communication between the multiple cores enables the migration of many "board-level" type measurements down to the chip level.     

The extended quadratic residue code is the only (48,24,12) self-dual doubly-even code

An extremal self-dual doubly-even binary (n,k,d) code has a minimum weight d=4/spl lfloor/n/24/spl rfloor/+4. Of such codes with length divisible by 24, the Golay code is the only (24,12,8) code, the extended quadratic residue code is the only known (48,24,12) code, and there is no known (72,36,16) code. One may partition the search for a (48,24,12) self-dual doubly-even code into three cases. A previous search assuming one of the cases found only the extended quadratic residue code. We examine the remaining two cases. Separate searches assuming each of the remaining cases found no codes and thus the extended quadratic residue code is the only doubly-even self-dual (48,24,12) code.     

Analysis of the Scattering Characteristic of Several Waveguide Components Using Boundary Element Method

Several kinds of waveguide components such as curved waveguide bends, arbitrary angle waveguide bends and T-junctions have been analyzed with boundary element method in this paper. A new discretization method for the boundary element method to solve the waveguide discontinuities has been given. The numerical results obtained agree well with the experimental results and numerical results in other literature. Especially, the scattering characteristics of Forded E-, H-plane T-junctions in 3mm band have been analyzed using boundary element method and the calculation results are presented.     

黄河龙口水利枢纽坝基岩体钙质充填夹层地质分析与试验研究

龙口水利枢纽坝基岩体主要由奥陶系中统马家沟组(O2m2)灰岩组成,其中发育有多层软弱夹层。作为其中之一的钙质充填夹层,强度虽不很低,但由于处于坝基下的持力层内,间距不大,发育密集,产状平缓,是坝基浅层抗滑稳定的主要控制因素,因此,在大坝抗滑稳定分析时,应进行分析和研究。     

On the effect of spatial variances in historical rainfall time series to CSO performance evaluation.

Historical, high-resolution rain series are the backbone of modern combined sewer overflow (CSO) structure design. These rain series are the input to the computational estimation of the performance of the measures with respect to CSO pollution abatement. However, those historical precipitation measurements are available at only a few locations. Frequently rain series have to be used from gauging stations at a significant distance. In order to judge and to compensate for this influence an estimate between rain characteristics and combined sewer outflow (CSO) performance indicators would be useful. In this paper such correlations have been sought for a collection of 37 rain series covering large areas of Europe. It was found that the mean annual rain volume can explain most of the variances for the performance indicators Number of overflows and CSO volume. For explaining the spatial differences in the efficiency of the CSO structure another rain characteristic, i.e. the maximum event with a return period of one year, is to be used.     

HDI工艺中取代涂树脂铜箔适合激光钻孔的半固化片

应用于HDI的激光钻孔半固化片的方法和其它常规材料相比具有的优缺点。