A digital wind gust recorder

The instrument was a byproduct of an undergraduate final year project on wind power which was carried out by the Department of Mechanical Engineering of the University of Liverpool.The windmill test site was on an exposed, rocky island where there was no history of weather recording but a long tradition of violent winds.Field experience during the winter months suggested that corrosion fatigue arising from wind buffeting and salt spray would rank equally with maximum wind pressure as criteria of failure and if modern materials, so convenient for forming aerodynamic surfaces, were to be used then limited life concepts would need to be considered. This called for more knowledge of wind variations at the test site. A complete wind spectrum taken on chart recording instruments would have been ideal but since such such refined devices were not available the instrument to be described was designed.The only wind measuring instrument which was available was a rotating cup anemometer. This supplied an alternating voltage proportional to its rotational speed. It also operated a gear driven microswitch which could give an integrated “miles of wind” reading on an electromagnetic counter.Briefly the e.m.f. generated by the anemometer (Fig. 1) was matched against a pre-set voltage corresponding to the required gust velocity. When this was exceeded an appropriate counter was operated. Only the rising e.m.f. was significant. The subsequent fall was ignored. Initially three stages were incorporated which reported the gusts rising through forty, fifty and sixty knots, respectively. These recorded on separate counters. All basic settings were based on pitot-static speed determinations in a wind tunnel.     

The effect of a sprinkler on the stability of a smoke layer beneath a ceiling

A study has been made of the effect of sprinkler sprays on hot buoyant smoke layers with particular reference to covered shopping malls.     

Enhancement of bond strength for epoxy-coated rebar using river sand

In this paper, improvement of bond strength for epoxy-coated rebars is studied. Although the epoxy-coated rebar is well accepted as an alternative corrosion prevention method in engineering practice, it still suffers from its poor bond performance, which requires modification of design parameters such as development length and splice length. Following our previous study [Proceedings of the Third Structure Engineering Conference (1996) 651–659], it is proposed to mix the river sand in the epoxy to improve the bond strength of epoxy-coated rebar. Specimens of several sizes of river sand and sand/epoxy weight ratios were studied. The single-rebar pullout test was performed to examine the bond strength. The open circuit potential method and the linear DC polarization method were conducted for corrosion rate measurements to ensure for keeping the merit of epoxy-coated rebar, i.e. the ability of corrosion. Experimental results show that the proposed method is very promising.     

Application of GaN-based ultraviolet-C light emitting diodes--UV LEDs--for water disinfection

GaN-based ultraviolet-C (UV-C) light emitting diodes (LEDs) are of great interest for water disinfection. They offer significant advantages compared to conventional mercury lamps due to their compact form factor, low power requirements, high efficiency, non-toxicity, and overall robustness. However, despite the significant progress in the performance of semiconductor based UV LEDs that has been achieved in recent years, these devices still suffer from low emission power and relatively short lifetimes. Even the best UV LEDs exhibit external quantum efficiencies of only 1-2%.The objective of this study was to investigate the suitability of GaN-based UV LEDs for water disinfection. The investigation included the evaluation of the performance characteristics of UV LEDs at different operating conditions as well as the design of a UV LED module in view of the requirements for water treatment applications. Bioanalytical testing was conducted using Bacillus subtilis spores as test organism and UV LED modules with emission wavelengths of 269 nm and 282 nm.The results demonstrate the functionality of the developed UV LED disinfection modules. GaN-based UV LEDs effectively inactivated B. subtilis spores during static and flow-through tests applying varying water qualities. The 269 nm LEDs reached a higher level of inactivation than the 282 nm LEDs for the same applied fluence. The lower inactivation achieved by the 282 nm LEDs was compensated by their higher photon flux. First flow-through tests indicate a linear correlation between inactivation and fluence, demonstrating a well designed flow-through reactor. With improved light output and reduced costs, GaN-based UV LEDs can provide a promising alternative for decentralised and mobile water disinfection systems.     

Measurement of the intrinsic process zone in rock using acoustic emission

Laboratory specimens with a smooth boundary (no notch) were fabricated from four different rock types (grain sizes from 0.1–10 mm) and were tested in three-point bending. The locations of acoustic emission that occurred around peak load were used to characterize the dimensions of the region of localized microcracking, the so-called intrinsic process zone. The size of this zone was found to vary significantly between the rock types, but was not found to vary significantly for different size beams of the same material. An approximately linear relation was found between the width of the intrinsic process zone and the logarithm of the grain size. An explanation of size effect evolves naturally by considering the intrinsic process zone as a material characteristic. Two different models were used to analyze stress at failure. The first treated the intrinsic process zone as a mathematical crack, an infinite stress raiser, from which a K_IC value was calculated. The second model assumed the intrinsic process zone was a cohesive notch, a finite stress raiser, from which the theoretical tensile strength was defined. The second method seemed somewhat better at predicting size effect on nominal peak stress.     

ROBOT软件在特种结构计算中的应用

结合实例介绍有限元结构分析软件ROBOT在特种结构空间分析中的应用。     

Development of passive viscoelastic damper to attenuate excessive floor vibrations

Recent changes in the construction of building floors have included the use of light material composite systems and long span floor systems. Although these changes have many advantages, such floor systems can suffer from excessive vibration due to human activities. This problem is exacerbated in office buildings due to the reduction in inherent damping associated with modern fit outs. Excessive floor vibrations are often realised after the completion of construction or following structural modifications and normally arise due to inadequate knowledge of the damping values in the design process. Thus rectification measures are normally required to reduce floor accelerations. This paper proposes a new innovative passive viscoelastic damper to reduce floor vibrations. This damper can be easily tuned to the fundamental frequency of the floor and can be designed to achieve various damping values. The paper discusses the analytical development of the damper with experimental results presented on a prototype to demonstrate its effectiveness.     

Seismic methods for study of soil building properties

Bulletin of Engineering Geology and the Environment - Information about distribution of elastic wave propagation velocities Vp, Vs in the subsurface zone of a soil mass can be obtained rapidly and...     

Stable lead isotopes and lake sediments--a useful combination for the study of atmospheric lead pollution history

Analysis of stable lead isotopes and lead concentrations in lake-sediment deposits, not least in varved (annually-laminated) sediments, is a useful method to study lead pollution history. This paper presents details from a study of 31 lakes in Sweden. Using a strong acid digestion of sediment samples and ICP-MS analyses, we have found that Swedish lake sediments have a high natural (pre-pollution) 206[Pb]207[Pb] ratio (mean 1.52+/-0.18, range 1.28-2.01, n=31 lakes). In contrast, atmospheric lead pollution derived from metal smelting processes, coal burning and from alkyl-lead added to petrol has a lower ratio (< 1.2). Consequently, when pollution lead deposition began approximately 3500 years ago, the lead isotope ratio of the sediments started to decline, and in modern sediments it is typically < 1.2. Using the isotope and concentration values and a mixing model, the relative contribution of pollution and natural lead in sediment samples can be calculated. The pollution lead records of the Swedish lake sediments show a consistent picture of the atmospheric lead pollution history. Some noticeable features are the Roman peak (approx. 0 AD), the large and permanent Medieval increase (approx. 1000 AD), peaks at approximately 1200 and 1530 AD, the rapid increase after World War II, the peak in the 1970s, and the large modern decline.