Surface performance of workpieces processed by electrical discharge machining in gas

The surface performance of workpieces processed by electrical discharge machining in gas(dry EDM)was studied in this paper.Firstly,the composition,micro hardness and recast layer of electrical discharge machined(EDMed)surface of 45 carbon steels in air were investigated through different test analysis methods.The results show that the workpiece surface EDMed in air contains a certain quantity of oxide,and oxidation occurs on the workpiece surface.Compared with the surface of workpieces processed in kerosene,fewer cracks exist on the dry EDMed workpiece surface,and the surface recast layer is thinner than that obtained by conventional EDM.The micro hardness of workpieces machined by dry EDM method is lower than that machined in kerosene,and higher than that of the matrix.In addition,experiments were conducted on the surface wear resistance of workpieces processed in air and kerosene using copper electrode and titanium alloy electrode.The results indicate that the surface wear resistance of workpieces processed in air can be improved,and it is related with tool material and dielectric.     

Rotordynamic forces generated by discharge-to-suction leakage flows in centrifugal pumps

In order to investigate the flow-induced vibration in the shroud passage of centrifugal pump and predict rotordynamic forces of centrifugal pump rotor system,an analysis of rotordynamic forces arising from shrouded centrifugal pump is presented. CFD techniques were utilized to analyze the full three-dimensional viscous,primary/secondary flow field in a centrifugal pump impeller to determine rotordynamic forces. Multiple quasi-steady solutions of an eccentric three-dimensional model at different whirl frequency ratios yielded the rotordynamic forces. The skew-symmetric stiffness,damping,and mass matrices were obtained by second-order least-squares analysis. Simulation of the coupled primary/secondary flow field was conducted,and the complex flow characteristics in the flow field of a shroud passage were achieved including the mean velocity and pressure,as well as the eddy in a large scale of flow field due to viscosity. The rotordynamic force coefficients were calculated,and the results were in good agreement with those of experiment except for the direct inertial coefficient without the consideration of whirling forces from the impeller primary flow passage.     

Relationship of hydrocarbon and source-rock in Nos.3-5 tectonic belts of the Lenghu area, northern Qaidam Basin

Based on analyses of the components of crude oil hydrocarbons and carbon isotopes, the content of normal alkane de-creased from 49.00% to 20.10% when moving from the No.3 to No.5 tectonic belt of the Lenghu area of the Qaidam Basin, while cycloalkanes increased from 30.00% to 52.20% and aromatic and branch chain alkanes increased gradually as well. The maturity of sterane in crude oil is higher than that of its source-rock, which shows that the hydrocarbons were generated from a deep source-rock of high maturity around the tectonic belts of the Lenghu area. The analysis of the characteristics of carbon isotopes also shows that these isotopes of hydrocarbon compounds in the No.4 and No.5 tectonic belt are apparently heavier than those in the No.3 belt. The results of our research show that the hydrocarbons in the No.3 tectonic belt are mainly from a relatively rich sapropelic substance, while the hydrocarbons in the No.4 and No.5 tectonic belt originated mainly from organic matter of a rela-tively rich humic type substance.     

基于GPRS水管网无线监控系统设计

介绍了一种基于GPRS的供水管网监控系统的设计方法,选择了GPRS作为本系统的通信方式,利用工控软件组态王进行供水监控系统设计,以可编程控制器作为下位机实现供水管网的自动动态采集信号,对监控参数进行动态管理,完成现场设备的实时数据采集、远程数据传输等功能.     

一种多元复合地基复合模量的计算方法

多元复合地基的沉降计算依赖于其复合模量的取值.目前多元复合地基复合模量计算均未考虑桩对桩间土的侧向挤密作用,因而其沉降计算结果与实际值相差较大.而考虑桩体与桩间土的侧向挤压作用,依据线弹性变形理论,推求的多元复合地基的复合模量公式应用于工程实例,结果表明,该方法是合理可行的,并且存在着参数易于确定、方法简便、机理清楚的特点.     

基于神经网络和支持向量机的电能质量组合评价

电能质量在当代越来越受到重视.根据电能质量的概述,提炼出电能质量评价指标体系,并基于组合评价的原理,运用BP神经网络和支持向量机对其进行评价,通过检验,证明了评价方法的有效性.     

铜板轧制自调整参数模糊控制系统的建模与仿真

针对铜板轧制控制,利用模糊控制原理,提出自调整参数模糊控制方式,运用仿真软件Matlab实现这种控制器的建模与仿真.仿真结果表明,这种控制方式通过自调整参数,增强了系统实时控制效果,明显地改善了控制系统的动态性能,提高了系统的控制精度.     

锡崖沟瀑布景观工程水力模型试验研究

根据锡崖沟景区规划设计,沿锡崖沟水库溢洪道下部开凿底洞引水,在水库下游红岩大峡谷常年形成20 m宽大瀑布.以满足瀑布流的重力和紊动阻力相似的原则进行了其正态模型设计.通过模型放水试验表明：流量变化对瀑布水流流态影响很大,溢流槽空间狭小,加之上游进口扇形扩散段扩散角偏大,水流扩散不充分,堰顶溢流不均匀,瀑布景观效果差.将模型的溢流堰顶修改为T型复式断面后,顺应了水流的流动特性,在各级流量下均能获得比较好的瀑布景观效果.     

ENSO事件对松花江流域夏季降水的影响

对1951—2000年的ENSO事件对松花江流域夏季(6—8月)降水的影响进行了分析,结果显示:赤道中东太平洋海温异常与松花江流域夏季降水有很好的相关性,特别是ENSO事件出现后,El Nino事件影响年通常对应于松花江流域夏季降水偏多,La Nina事件影响年松花江流域夏季降水则较常年偏少,且二者通过了置信度α=0.05的显著性检验.这种相关性可用于进行松花江流域夏季降水的预测.     

基于CSY型传感器的悬臂力学试验确定材料弹性模量的方法

对在CSY型传感器综合实验仪上拓展悬臂梁力学实验进行了研究,研究了在该实验仪上实现材料弹性模量的测定.通过材料力学的理论推导出悬臂梁弹性模量与其受力和挠度比值的关系,通过应变式传感器的实验确定出悬臂梁受力与其挠度的比值关系,进一步可推导出悬臂梁材料的弹性模量,并验证了该方法的可行性及有效性.该方法集合了电阻应变效应、全桥差动电路等传感器电测技术以及材料弹性力学、悬臂梁结构力学的基础知识,具有综合应用性.同时,对高校实验室如何有效利用设备资源、开发拓展型实验有一定的示范作用.