Autocatalytic dissolution of Pb in HNO3

The reaction between Pb and HNO₃ has been investigated using the thermometric technique. Weight-loss measurements on the reaction were also obtained. As the HNO₃ concentration is increased from 5×10^–2 to 4mol l^–1, the corrosion rate increases. This is shown thermometrically by a substantial increase in the maximum temperature attained, T _m, as well as a decrease in the time, t, required for reaching T _m. Dissolution of Pb in HNO₃ is proposed to take place according to an autocatalytic mechanism. Passivation sets were detected in solutions 11 mol l^–1 HNO₃. A parallel indication between the thermometric technique and weight-loss measurements was obtained. The rate-determining step of the autocatalytic process involves HNO₂ in dissolution of Pb in HNO₃. This is supported by the results of addition of hydrazine to the solution. This additive raises the maximum measured temperature, without affecting the corresponding time necessary to reach it. The effect of addition of NaNO₂, NaNO₃, NaCl, Na₂SO₄, NaH₂PO₄ and NaClO₄ on the reaction number, RN, of Pb in 4 mol l^–1 HNO₃ was examined. Only NaNO₂ accelerates the dissolution reaction while the other salts show as inhibition effect. It was found that these additives inhibit dissolution due to the displacement of some cathodic depolarizing components, as NO₂, from the active sites on the metal surface. The effect of addition of HCl, H₂SO₄, HClO₄ and H₃PO₄ on the reaction number, RN, of Pb in 4 mol l^–1 HNO₃ was also investigated. The observed acceleration and retardation of the dissolution of Pb was found to be dependent on both the concentration and nature of anions of the extra acids added.     

Fabrication,Electrical and Photovoltaic Characterizations of SnSb2S4/n-Si Heterojunction

Silicon - An inexpensive spray pyrolysis technique was effectively used to form a p-type SnSb2S4 thin film on n-type Si wafer for the first time to produce SnSb2S4/n-Si heterojunction. The...     

Probing the Structural and Antimicrobial Study on a Sol–Gel Derived Velosef-Loaded Bioactive Calcium Magneso-Silicate Xerogel

Silicon - The nature of the opening silicate- based surface affects the chemical interaction, spectroscopic and antimicrobial efficiency. The aim of this approach was to evaluate the spectroscopic...     

Eco-friendly Geopolymer Composite Based on Non-heat-treated Phosphate Sludge Reinforced With Polypropylene Fibers

Silicon - Geopolymers produced with metakaolin (MK) and thermally untreated phosphate sludge (PS) are beneficial and environmentally advantageous materials, but their fragility limits its...     

Modern Template Design and Biological Evaluation of Cephradine-loaded Magnesium Calcium Silicate Nanocomposites as an Inhibitor for Nosocomial Bacteria in Biomedical Applications

Silicon - Magnesium calcium silicate nanostructures (MCSNS) loaded with (0.0, 0.6, 0.9, and 1.2 wt%) of Cephradine-drug consisting of mesoporous particles were functionally prepared by sol-gel...     

Crude Wax Extracted from Rice Bran Oil Improves Oleogel Properties and Oxidative Stability

Crude wax extracted from rice bran oil (RBO) is used to improve the oleogel properties and oxidative stability of RBO. The effect of crude rice bran wax (CrBW) on the formation characteristics and oxidative stability of oleogels is discussed. The results show that oleogels can be formed with 7.0 wt% CrBW at 20 °C. As the concentration of CrBW increases from 7.0 to 11.0 wt%, the hardness and solid fat content (SFC) of the oleogels increase significantly, and the oleogels are primarily β' crystals. Moreover, oleogel crystals formed with 5 and 7 wt% CrBW are flocculent; when the amount included is 9%, the oleogel crystals are transformed into long dendrites, and the density rises. After 90 days of storage at 20 °C, the peroxide value of oleogels formed with 9.0 wt% CrBW slowly rises from 3.21 to 6.52 mmol kg⁻¹. Practical Applications: Oleogels prepared here by CrBW and RBO are an innovative structural lipid without trans fats. Useful information on the rich fats and nutrients in CrBW is provided, which reduces the production cost and improves the industrial production capacity.     

Preparation,Properties and Applications of the Hybrid Organic/Inorganic Nanocomposite Based on Nanoporous Carbon Matrix

Journal of Inorganic and Organometallic Polymers and Materials - Nanoporous carbon matrix was prepared by the sol–gel process from pyrogallol-formaldehyde (PF) mixtures in water using picric...     

A Multi-Channel Pulse-Coded Multiplexing and Demodulating Telemetry System

A multiplexing, demodulating, and recording telemetry system designed to process multiple pulse-coded temperature channels is described. The system provides complete control of recording and multiplexing sequences and timing, and gives a single analog signal in response to each sample of pulse-coded data. It identifies all channels and indicates to a computer when a new data sample is to be processed. The system is self-calibrating to maintain accuracy over extended data collection periods, and is inexpensive.     

Miniemulsion and conventional emulsion copolymerization of styrene and butadiene: Effect of process on gel content

The properties of styrene/butadiene copolymers obtained by conventional emulsion and miniemulsion polymerizations were studied. Thin layer chromatography with flame ionization detection was used to determine the gel fraction of the copolymer in the latex particles as a function of conversion. It was found that the gel formation began at a higher conversion in the miniemulsion polymerization when compared with that in the conventional process. Also, a lower glass transition temperature was noted at the lowest conversion sampled (～25%), implying a higher initial butadiene monomer concentration within the nucleated miniemulsion monomer droplets when compared with particles formed conventionally. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4616–4622, 2006