Experimental Thermal Performance Characterization of Flat Grooved Heat Pipes

ABSTRACT

The thermal characterization of aluminum flat grooved heat pipes is performed experimentally for different groove dimensions. Three heat pipes with groove widths of 0.2?mm, 0.4?mm, and 1.5?mm are used in the experiments. The effect of the amount of the working fluid is extensively studied for each groove width. The results reveal that, although all three succeed in dissipating the heat input through the phase change of the working fluid by continuous evaporation and condensation, the effectiveness of the heat transfer increases with reduced groove width. Furthermore, it is observed that there exists an optimum operating point, where the temperature difference between the heating and cooling sections is at a minimum, and the magnitude of this temperature difference is a strong function of the groove width. To the best of the authors’ knowledge, the combined effects of groove dimensions and the amount of the working fluid, from fully flooded to dry, is reported for the first time for aluminum flat grooved heat pipes.     

液滴撞击干燥倾斜壁面铺展实验研究

通过高速摄影技术及像素分析方法对液滴撞击干燥倾斜壁面进行实验研究，分析了不同倾斜角及韦伯数（We）对液滴飞溅及铺展的影响，结果表明，倾斜角的增加有利于抑制飞溅的产生；We一定时，液滴的前铺展因子随着倾斜角的增加而增加，后铺展因子随着倾斜角的增加而减小；液滴的前后初始铺展速度均大于液滴的撞击速度，且随着倾斜角的增加而减小。      

应变纤锌矿ZnO/MgxZn1-xO量子点中离子施主束缚激子的光学性质

Within the framework of the effective-mass approximation and the dipole approximation, considering the three-dimensional confinement of the electron and hole and the strong built-in electric field(BEF) in strained wurtzite Zn O/Mg0:25Zn0:75O quantum dots(QDs), the optical properties of ionized donor-bound excitons(D+, X)are investigated theoretically using a variational method. The computations are performed in the case of finite band offset. Numerical results indicate that the optical properties of(D+, X) complexes sensitively depend on the donor position, the QD size and the BEF. The binding energy of(D+, X) complexes is larger when the donor is located in the vicinity of the left interface of the QDs, and it decreases with increasing QD size. The oscillator strength reduces with an increase in the dot height and increases with an increase in the dot radius. Furthermore, when the QD size decreases, the absorption peak intensity shows a marked increment, and the absorption coefficient peak has a blueshift. The strong BEF causes a redshift of the absorption coefficient peak and causes the absorption peak intensity to decrease remarkably. The physical reasons for these relationships have been analyzed in depth.     

Mesoporous g-C3N4 decorated by Ni2P nanoparticles and CdS nanorods together for enhancing photocatalytic hydrogen evolution

Ni₂P nanoparticles and CdS nanorods were grew together on a mesoporous g-C₃N₄ through a facile in-situ solvothermal approach. Under visible light (λ > 400 nm), the as-prepared ternary PCN–CdS-5% Ni₂P composite displays a high H₂ evolution rate with 2905.86 μmol g^?1 h^?1, which is about 14, 18 and 279 times that of PCN–CdS, PCN–Ni₂P and PCN, respectively. The enhanced photocatalytic activity is mainly attributed to the improved separation efficiency of the photocarriers by the type II PCN–CdS heterojunction and the effective extraction of photogenerated electrons by Ni₂P. Meanwhile, Ni₂P acts as co-catalyst to provide the photocatalytic active site for hydrogen reduction. In addition, PCN–CdS-5% Ni₂P composite exerts good stability in 12-h cycles.     

Cathode plasma electrolytic deposition of Al2O3 coatings doped with SiC particles

Semiconductor particles doped Al₂O₃ coatings were prepared by cathode plasma electrolytic deposition in Al(NO₃)₃ electrolyte dispersed with SiC micro- and nano-particles (average particle sizes of 0.5–1.7?µm and 40?nm respectively). The effects of the concentrations and particle sizes of the SiC on the microstructures and tribological performances of the composite coatings were studied. In comparison with the case of dispersing with SiC microparticles, the dispersion of SiC nanoparticles in the coatings was more uniform. When the concentration of SiC nanoparticles was 5?g/L, the surface roughness of the composite coating was reduced by 63%, compared with that of the unmodified coating. Friction results demonstrated that the addition of 5?g/L SiC nanoparticles reduced the friction coefficient from 0.60 to 0.38 and decreased the wear volume under dry friction. The current density and bath voltage were measured to analyze the effects of SiC particles on the deposition process. The results showed that the SiC particles could alter the electrical behavior of the coatings during the deposition process, weaken the bombardment of the plasma, and improve the structures of the coatings.     

Chemotherapy response of pancreatic cancer by diffusion-weighted imaging (DWI) and intravoxel incoherent motion DWI (IVIM-DWI) in an orthotopic mouse model

Magnetic Resonance Materials in Physics, Biology and Medicine - To investigate the value of using diffusion-weighted imaging (DWI) and intravoxel incoherent motion DWI (IVIM-DWI) to assess the...