Template-assisted synthesis of lamellar mesostructured hydroxyapatites

Novel lamellar mesostructured hydroxyapatites have firstly been synthesized by template-assisted technique. The mild and nontoxic surfactant, phosphoric acid monododecyl ester (MAP), is used to act as a structure-directing template. The structure of sample was characterized by X-ray diffraction, Fourier transform infrared spectroscopy, Scanning electron microscope and Transmission electron microscopy. The results indicate that the obtained sample is a well-organized lamellar mesostructured hydroxyapatite with a uniform layer spacing of 3.64 nm.     

宝钢2号高炉4号热风炉凉炉实践

对宝钢2号高炉4号热风炉凉炉的原因、凉炉的前期族备工作、凉炉的设备和方法以及凉炉的实际效果进行了总结。通过这次凉炉实践，取得了一些有价值的经验，这些经验对今后宝钢砖硅热风炉的凉炉具有重要的参考意义。     

Trellis and convolutional precoding for transmitter-based interference presubtraction

This paper studies the combination of practical trellis and convolution codes with Tomlinson-Harashima precoding (THP) for the presubtraction of multiuser interference that is known at the transmitter but not known at the receiver. It is well known that a straightforward application of THP suffers power, modulo, and shaping losses. This paper proposes generalizations of THP that recover some of these losses. At a high signal-to-noise ratio (SNR), the precoding loss is dominated by the shaping loss, which is about 1.53 dB. To recover shaping loss, a trellis-shaping technique is developed that takes into account the knowledge of a noncausal interfering sequence, rather than just the instantaneous interference. At rates of 2 and 3 bits per transmission, trellis shaping is shown to be able to recover almost all of the 1.53-dB shaping loss. At a low SNR, the precoding loss is dominated by power and modulo losses, which can be as large as 3-4 dB. To recover these losses, a technique that incorporates partial interference presubtraction (PIP) within convolutional decoding is developed. At rates of 0.5 and 0.25 bits per transmission, PIP is able to recover 1-1.5 dB of the power loss. For intermediate SNR channels, a combination of the two schemes is shown to recover both power and shaping losses.     

N,N''-取代邻苯二胺的合成

通过2-取代苯并咪唑盐的还原开环反应制备了8个N,N′-不同取代的邻苯二胺,并经1HNMR、IR、MS及元素分析表征,其中5个未见文献报道.这是一条由邻苯二胺和羧酸经2.取代苯并咪唑制取该类化合物的简洁合成路线.     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

The cooling and solidification of melted drops during their movement in an immiscible cooling medium is widely employed for granulation in the chemical industry, and a study of these processes to provides a basis for the design of the granulation tower height and the temperature of the cooling medium is reported. A physical model of the cooling and solidification of the drop is established and the numerical calculation is performed. The influences of the key factors in the solidification, i.e., Bi number, drop diameter, temperature of the cooling medium, etc. are presented. The cooling and solidification during wax granulation in a water‐cooling tower and during urea granulation in an air‐cooling tower (spraying tower) are described in detail. Characteristics of the solidification and temperature distribution within the particle at different times are shown. The model and calculations can be used for structure design of the granulation tower and optimization of the operation parameters.     

Poly(butylene terephthalate)–clay nanocomposites prepared by melt intercalation: morphology and thermomechanical properties

Nanocomposites based on poly(butylene terephthalate) (PBT) and an organoclay (Cloisite 30B) were prepared by melt blending using a twin‐screw extruder. Two kinds of PBTs, ie PBT‐A and PBT‐B, with different inherent viscosities (η_inh), were used for this study (η_inh of PBT‐A and PBT‐B were 0.74 and 1.48, respectively). Dispersion of the clay layers in the PBT nanocomposites was characterized by using X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Tensile and dynamic mechanical properties and non‐isothermal crystallization temperatures of the nanocomposites were also examined. Nanocomposites based on the higher‐viscosity PBT (PBT‐B) showed a higher degree of exfoliation of the clay and a higher reinforcing effect when compared to the composites based on the lower‐viscosity PBT (PBT‐A). The clay nanolayers dispersed in PBT matrices lead to increases in the non‐isothermal crystallization temperatures of the PBTs, with such increases being more significant for the PBT‐B nanocomposites than for the PBT‐A nanoocomposites. Copyright © 2004 Society of Chemical Industry     

Facile modifications of polyimide via chloromethylation: II. Synthesis and characterization of thermocurable transparent polyimide having methylene acrylate side groups

From chloromethylated polyimide, a useful starting material for modification of aromatic polyimides, a thermocurable transparent polyimide having acrylate side groups was prepared. In the presence of 1,8‐diazabicyclo[5,4,0]undec‐7‐ene, chloromethylated polyimide was esterified with acrylic acid to synthesize poly(imide methylene acrylate). The polymer was soluble in organic solvent, which makes it possible to prepare a planar film by spin coating. The polymer film became insoluble after thermal treatment at 230 °C for 30 min. Optical transparency of the film at 400 nm (for 1 µm thickness) was higher than 98 % and not affected by further heating at 230 °C for 250 min. Adhesion properties measured by the ASTM D3359‐B method ranged from 4B to 5B. Preliminary results of planarization testing showed a high degree of planarization (DOP) value (>0.53). These properties demonstrate that poly(imide methylene acrylate) could be utilized as a thermocurable transparent material in fabricating display devices such as TFT‐LCD. Copyright © 2004 Society of Chemical Industry     

Properties of poly(ethylene terephthalate)–poly(ethylene naphthalene 2,6‐dicarboxylate) blends with montmorillonite clay

The production and properties of blends of poly(ethylene terephthalate) (PET) and poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) with three modified clays are reported. Octadecylammonium chloride and maleic anhydride (MAH) are used to modify the surface of the montmorillonite–Na⁺ clay particles (clay–Na⁺) to produce clay–C18 and clay–MAH, respectively, before they are mixed with the PET/PEN system. The transesterification degree, hydrophobicity and the effect of the clays on the mechanical, rheological and thermal properties are analysed. The PET–PEN/clay–C18 system does not show any improvements in the mechanical properties, which is attributed to poor exfoliation. On the other hand, in the PET–PEN/clay–MAH blends, the modified clay restricts crystallization of the matrix, as evidenced in the low value of the crystallization enthalpy. The process‐induced PET–PEN transesterification reaction is affected by the clay particles. Clay–C18 induces the largest proportion of naphthalate–ethylene–terephthalate (NET) blocks, as opposed to clay–Na⁺ which renders the lowest proportion. The clay readily incorporates in the bulk polymer, but receding contact‐angle measurements reveal a small influence of the particles on the surface properties of the sample. The clay–Na⁺ blend shows a predominant solid‐like behaviour, as evidenced by the magnitude of the storage modulus in the low‐frequency range, which reflects a high entanglement density and a substantial degree of polymer–particle interactions. Copyright © 2005 Society of Chemical Industry