Performance evaluation of a water/silicone oil two‐phase partitioning bioreactor using Rhodococcus erythropolis T902.1 to remove volatile organic compounds from gaseous effluents

BACKGROUND: In the framework of biological processes used for waste gas treatment, the impact of the inoculum size on the start‐up performance needs to be better evaluated. Moreover, only a few studies have investigated the behaviour of elimination capacity and biomass viability in a two‐phase partitioning bioreactor (TPPB) used for waste gas treatment. Lastly, the impact of ethanol as a co‐substrate remains misunderstood. RESULTS: Firstly, no benefit of inoculation with a high cellular density (>1.5 g L^?1) was observed in terms of start‐up performance. Secondly, the TPPB was monitored for 38 days to characterise its behaviour under several operational conditions. The removal efficiency remained above 63% for an inlet concentration of 7 g isopropylbenzene (IPB) m^?3 and at some time points reached 92% during an intermittent loading phase (10 h day^?1), corresponding to a mean elimination capacity of 4 × 10^?3 g L^?1 min^?1 (240 g m^?3 h^?1) for a mean IPB inlet load of 6.19 × 10^?3 g L^?1 min^?1 (390 g m^?3 h^?1). Under continuous IPB loading, the performance of the TPPB declined, but the period of biomass acclimatisation to this operational condition was shorter than 5 days. The biomass grew to approximately 10 g L^?1 but the cellular viability changed greatly during the experiment, suggesting an endorespiration phenomenon in the bioreactor. It was also shown that simultaneous degradation of IPB and ethanol occurred, suggesting that ethanol improves the biodegradation process without causing oxygen depletion. CONCLUSION: A water/silicone oil TPPB with ethanol as co‐substrate allowed the removal of a high inlet load of IPB during an experiment lasting 38 days. Copyright © 2008 Society of Chemical Industry     

Simultaneous sulfide and acetate oxidation under denitrifying conditions using an inverse fluidized bed reactor

BACKGROUND: Simultaneous removal of sulfur, nitrogen and carbon compounds from wastewaters is a commercially important biological process. The objective was to evaluate the influence of the CH₃COO^?/NO₃^? molar ratio on the sulfide oxidation process using an inverse fluidized bed reactor (IFBR). RESULTS: Three molar ratios of CH₃COO^?/NO₃^? (0.85, 0.72 and 0.62) with a constant S^2?/NO₃^? molar ratio of 0.13 were evaluated. At a CH₃COO^?/NO₃^? molar ratio of 0.85, the nitrate, acetate and sulfide removal efficiencies were approximately 100%. The N₂ yield (g N₂ g^?1 NO₃^?‐N consumed) was 0.81. Acetate was mineralized, resulting in a yield of 0.65 g inorganic‐C g^?1 CH₃COO^?‐C consumed. Sulfide was partially oxidized to S⁰, and 71% of the S^2? consumed was recovered as elemental sulfur by a settler installed in the IFBR. At a CH₃COO^?/NO₃^? molar ratio of 0.72, the efficiencies of nitrate, acetate and sulfide consumption were of 100%, with N₂ and inorganic‐C yields of 0.84 and 0.69, respectively. The sulfide was recovered as sulfate instead of S⁰, with a yield of 0.92 g SO₄^2?‐S g^?1 S^2? consumed. CONCLUSIONS: The CH₃COO^?/NO₃^? molar ratio was shown to be an important parameter that can be used to control the fate of sulfide oxidation to either S⁰ or sulfate. In this study, the potential of denitrification for the simultaneous removal of organic matter, sulfide and nitrate from wastewaters was demonstrated, obtaining CO₂, S⁰ and N₂ as the major end products. Copyright © 2008 Society of Chemical Industry     

Ennoblement of stainless steel in natural seawater – A new explanation

The ennoblement of corrosion potential (E_corr) of passive metal immersed in seawater was investigated with electrochemical technology and epifluorescence microscopy. The in situ observation showed that the bacteria number increased on the metal surface according to an exponential law which was in the same way with the ennoblement of E_corr. At the same time, the anodic polarization current of high‐Mo stainless steel decreased in the initial days. According to the mix‐potential theory and the characteristics of polarization curves of high‐Mo steel in natural seawater, the ennoblement of corrosion potential may be induced by the decrease of the passive current density.     

Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

One-to-Many and Many-to-One Optical Chaos Communications Using Semiconductor Lasers

A theoretical construction of one-to-many (OTM) and many-to-one (MTO) chaos synchronization communications using semiconductor lasers is presented. One center laser provides strong injections (strong link) to other side lasers, and the side lasers also provide weak injections (weak link) to the center one. Simulation results show that the side lasers synchronize with the center laser through injection-locking. In addition, messages transmitted via the strong links or the weak links experience strong chaos pass filtering, enabling us to realize OTM and MTO communications.     

Optimal and self‐tuning fusion Kalman filters for discrete‐time stochastic singular systems

Based on the optimal fusion estimation algorithm weighted by scalars in the linear minimum variance sense, a distributed optimal fusion Kalman filter weighted by scalars is presented for discrete‐time stochastic singular systems with multiple sensors and correlated noises. A cross‐covariance matrix of filtering errors between any two sensors is derived. When the noise statistical information is unknown, a distributed identification approach is presented based on correlation functions and the weighted average method. Further, a distributed self‐tuning fusion filter is given, which includes two stage fusions where the first‐stage fusion is used to identify the noise covariance and the second‐stage fusion is used to obtain the fusion state filter. A simulation verifies the effectiveness of the proposed algorithm. Copyright © 2008 John Wiley & Sons, Ltd.     

论检察机关对行政判决执行的监督

缺乏有力的监督和制约机制是我国行政判决执行难的重要原因之一.主张赋予检察机关时行政诉讼执行环节实施法律监督的权利.从而有效防止执行程序违法.抑制怠于执行和拖延执行现象的发生.阐述了由检察机关实施监督的法理依据,介绍了检察监督的方式.     

Note on ‘Construction of Double Sampling s‐Control Charts for Agile Manufacturing’

He and Grigoryan (Quality and Reliability Engineering International 2002; 18 :343–355) formulated the design of a double‐sampling (DS) s control chart as an optimization problem and solved it with a genetic algorithm. They concluded that the DS s control charts can be a more economically preferable alternative in detecting small shifts than traditional s control charts. We explain that, since they only considered the average sample size when the process is in control, their conclusion is questionable. Copyright © 2006 John Wiley & Sons, Ltd.