Incompressible dipping substrata are commonly encountered in engineering practice. Compared to horizontal underlying strata, the inclined underlying stratum increase the risk of collapse of embankments reinforced with columns because it weakens the restraint of the column base. The objective of this study is to investigate the effectiveness of geosynthetics on improving the embankment stability when the underlying stratum is inclined. The influence of geosynthetic tensile stiffness on the ultimate surcharge and failure mechanism is studied. A deep-seated failure with column tilting occurs when the geosynthetic tensile stiffness is low, whereas a lateral sliding occurs when the geosynthetic tensile stiffness is high. To illustrate the contribution of geosynthetics, the distribution of the lateral pressures acting on the columns is analyzed. 相似文献
Thermosetting materials are widely used as encapsulation in the electrical packaging to protect the core electronic components from external force, moisture, dust, and other factors. However, the spreading and curing behaviors of such kind of fluid on a heated surface have been rarely explored. In this study, we experimentally and numerically investigated the spreading and curing behaviors of the silicone(OE6550 A/B, which is widely used in the light-emitting diode packaging) droplet with diameter of ~2.2 mm on a heated surface with temperature ranging from 25 ℃ to 250 ℃. For the experiments, we established a setup with high-speed camera and heating unit to capture the fast spreading process of the silicone droplet on the heated surface. For the numerical simulation, we built a viscosity model of the silicone by using the Kiuna's model and combined the viscosity model with the Volume of Fluid(VOF) model by the User Defined Function(UDF) method. The results show that the surface temperature significantly affected the spreading behaviors of the silicone droplet since it determines the temperature and viscosity distribution inside the droplet. For surface temperature varied from 25 ℃ to 250 ℃, the final contact radius changed from ~2.95 mm to ~1.78 mm and the total spreading time changed from ~511 s to ~0.15 s. By further analyzing the viscosity evolution of the droplet, we found that the decreasing of the total spreading time was caused by the decrease of the viscosity under high surface temperature at initial spreading stage, while the reduction of the final contact radius was caused by the curing of the precursor film. This study supplies a strategy to tuning the spreading and curing behavior of silicone by imposing high surface temperature, which is of great importance to the electronic packaging. 相似文献
Journal of Communications Technology and Electronics - Approximate formulas for calculating the coefficient of reflection from an artificial magnetic conductor (AMC) based on a capacitive lattice... 相似文献
Theoretical Foundations of Chemical Engineering - A choline chloride–sulfosalicylic acid deep eutectic solvent (DES) is proposed for dissolving the oxides Co(II), Cu(II), Zn(II), Fe(III),... 相似文献
Atomic Energy - The results of calculations and experimental determination of the neutronics characteristics of the IRT-T research reactor are presented. The IRT-T reactor is a pool reactor with... 相似文献
The effects of La2O3–Al2O3–SiO2 addition on the thermal conductivity, coefficient of thermal expansion (CTE), Young's modulus and cyclic thermal shock resistance of hot-pressed h-BN composite ceramics were investigated. The samples were heated to 1000 °C and then quenched to room temperature with 1–50 cycles, and the residual flexural strength was used to evaluate cyclic thermal shock resistance. h-BN composite ceramics containing 10 vol% La2O3–Al2O3 and 20 vol% SiO2 addition exhibited the highest flexural strength, thermal conductivity and relatively low CTE, which were beneficial to the excellent thermal shock resistance. In addition, the viscous amorphous phase of ternary La2O3–Al2O3–SiO2 system could accommodate and relax thermal stress contributing to the high thermal shock resistance. Therefore, the residual flexural strength still maintained the value of 234.3 MPa (86.9% of initial strength) after 50 cycles of thermal shock. 相似文献
We present a new scheme for visibly-opaque but near-infrared-transmitting filters involving 7 layers based on one-dimensional ternary photonic crystals, with capabilities in reaching nearly 100% transmission efficiency in the near-infrared region. Different decorative reflection colors can be created by adding additional three layers while maintaining the near-infrared transmission performance. In addition, our proposed structural colors show great angular insensitivity up to ±60° for both transverse electric and transverse magnetic polarizations, which are highly desired in various fields. The facile strategy described here involves a simple deposition method for the fabrication, thereby having great potential in diverse applications such as image sensors, anti-counterfeit tag, and optical measurement systems.