二氧化钛直接制取金属钛工艺简介

阐述了各种二氧化钛直接电解制取金属钛的工艺及其原理，指出了熔盐电解TiO2法在工业应用上存在的问题。     

周铣加工表面形貌仿真新算法

考虑主轴偏心，基于周铣过程中刀具切削刃上任意点与工件相对运动的轨迹方程和周铣过程几何特征，构造出可以求解周铣加工表面上任意一点形貌高度值的三维表面形貌仿真算法，并给出了相应的仿真算例。该算法无需对刀齿进行微段离散，并且不依赖于工件网格划分，加工表面上任意一点形貌高度值的计算次数等于刀具齿数，具有通用性好、运算速度快、结果准确度高的特点。     

湿法冶炼浸出过程H∞优化控制研究与设计

应用H∞优化控制方法对锌湿法冶炼浸出过程进行H∞优化控制器设计,同时,讨论了如何把浸出过程控制问题转化为H∞优化控制问题、浸出过程的输入输出量和H∞标准控制问题各量之间的关系及其物理意义.通过仿真实验,给出了几种情况下的仿真曲线,并进行了分析,从而得出结论.     

用正电子湮没研究含砷α黄铜的脱锌机制

分别测量了含０．００、０．０１、０．０３、０．０５、００７、０．１０ｗｔ％Ａｓ的６８ｗｔ％Ｃｕ－Ｚｎ合金在１％ＣｕＣｌ２水溶液中脱锌后的正电子寿命谱。讨论了黄铜脱锌及砷抑制脱锌的空位体扩散机制。     

痛挽往昔 瞻望来者——巴米扬窟龛考

本文整理出巴米扬山谷遗址群的年代学证据,旨在重现大佛的历史与图像地位。首先介绍了巴米扬山谷遗址群的研究方法和年代阶段,接着讨论玄奘所见所录的大佛的原始配置,最后将三尊佛像放入其原始的图像志语境中去考查,认为涅檗像原应位于38米大佛和55米大佛之间。后者为宝装焰肩佛,其神格应为燃灯佛;38米大佛为释迦佛。而巡礼者所遵循的应是燃灯佛-释迦佛-涅粲佛-弥勒佛的绕拜顺序。     

施工管理科学化的论述

施工管理中的施工技术管理、质量管理以及生产要素管理是施工管理的主要方面,处理好三者之间的关系以及解决好三个方面中的任何一方面是在施工中面临的重要问题     

基于函数插值的柯氏质量流量计信号处理方法

对基于离散傅里叶变换(DFT)信号处理方式的柯氏质量流量计来说,影响其精度的关键问题是如何实现信号的整周期采样。提出了一种全新的方法,用采样率固定不变的采样数据,通过软件实时地确定信号的频率并且实现信号整周期重新采样。实验结果表明该方法在求取相位差时具有极高的精度。     

A novel ethanol gas sensor based on ZnO-microwire

One-dimensional (1D) ZnO microwires were successfully synthesized by chemical vapor deposition and their structural and morphological properties were analyzed by X-ray diffraction and scanning electron microscopy, demonstrating that the microwires were single crystalline with perfect hexagonal structure and smooth surface. Using these 1D microstructures, we fabricated a novel ZnO-based ethanol gas sensor. Operating at room temperature, the sensor was found to have good sensing characteristics. The reliability and stability of the sensor could be improved by connecting multiple 1-wire devices (1-WD) in parallel into a multi-wires device. In interior natural lighting environment and under 3 V bias, the response and recovery time of the 1-WD to 200 ppm ethanol gas were <10 s and about 300 s, respectively, and the minimum and maximum detection limit were about 2 and 200 ppm, respectively. A sensing model was proposed for discussing the performance of the sensor. The simplicity in fabrication, low power consumption and low cost make the sensor suitable for practical application in many fields, especially in identifying driving under the influence and chemical industry monitoring.     

Comparison of the effects of Mg–6Zn and titanium on intestinal tract in vivo

To evaluate the ability of Mg–6Zn to replace titanium nails in the reconstruction of the intestinal tract in general surgery, we compared the Mg–6Zn and titanium implants with respect to their effects on rat’s intestinal tract by biochemical, radiological, pathological and immunohistochemical methods. The results indicated that Mg–6Zn implants started to degrade at the third week and disintegrate at the fourth week. No bubbles appeared, which may be associated with intestinal absorption of the Mg–6Zn implants. Pathological analyses (containing liver, kidney and cecum tissues) and biochemical measurements, including serum magnesium, creatinine, blood urea nitrogen, glutamic–pyruvic–transaminase and glutamic–oxaloacetic–transaminase proved that degradation of Mg–6Zn did not harm the important organs, which is an improvement over titanium implants. Immunohistochemical results showed that Mg–6Zn could enhance the expression of transforming growth factor-β₁. Mg–6Zn reduced the expression of tumor necrosis factor at different stages. In general, our study demonstrates that the Mg–6Zn alloy had good biocompatibility in vivo and performed better than titanium at promoting healing and reducing inflammation. It may be a promising candidate for stapler pins in intestinal reconstruction.