Dynamic mechanical properties and morphology of high‐density polyethylene/CaCO3 blends with and without an impact modifier

Dynamic mechanical analysis and differential scanning calorimetry were used to investigate the relaxations and crystallization of high‐density polyethylene (HDPE) reinforced with calcium carbonate (CaCO₃) particles and an elastomer. Five series of blends were designed and manufactured, including one series of binary blends composed of HDPE and amino acid treated CaCO₃ and four series of ternary blends composed of HDPE, treated or untreated CaCO₃, and a polyolefin elastomer [poly(ethylene‐co‐octene) (POE)] grafted with maleic anhydride. The analysis of the tan δ diagrams indicated that the ternary blends exhibited phase separation. The modulus increased significantly with the CaCO₃ content, and the glass‐transition temperature of POE was the leading parameter that controlled the mechanical properties of the ternary blends. The dynamic mechanical properties and crystallization of the blends were controlled by the synergistic effect of CaCO₃ and maleic anhydride grafted POE, which was favored by the core–shell structure of the inclusions. The treatment of the CaCO₃ filler had little influence on the mechanical properties and morphology. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3907–3914, 2007     

CaO-SiO2系玻璃的析晶动力学研究

利用溶胶-凝胶法制得CaO-SiO2系基础玻璃,通过差热分析曲线分析质量比为CaO-SiO2玻璃的析晶能力。经分析,其析晶活化能E=457.1kJ·mol-1,而晶化生长指数是随升温速率的不同而不同,速率越大,晶化生长指数越小。     

Synthesis and luminescence properties of new blue‐light‐emitting polyconjugated poly{1,1′‐biphenyl‐4,4′‐diyl‐[1‐(4‐t‐butylphenyl)]vinylene} polymers and copolymers

Three new soluble polyconjugated polymers, all of which emitted blue light in photoluminescence and electroluminescence, were synthesized, and their luminescence properties were studied. The polymers were poly{1,1′‐biphenyl‐4,4′‐diyl‐[1‐(4‐t‐butylphenyl)]vinylene}, poly((9,9‐dioctylfluorene‐2,7‐diyl)‐alt‐{1,4‐phenylene‐[1‐(4‐t‐butylphenyl)vinylene‐1,4‐phenylene]}) [P(DOF‐PVP)], and poly([N‐(2‐ethyl) hexylcarbazole‐3,6‐diyl]‐alt‐{1,4‐phenylene‐[1‐(4‐t‐butylphenyl)]vinylene‐1,4‐phenylene}). The last two polymers had alternating sequences of the two structural units. Among the three polymers, P(DOF‐PVP) performed best in the light‐emitting diode devices of indium–tin oxide/poly(ethylenedioxythiophene) doped with poly(styrene sulfonate) (30 nm)/polymer (150 nm)/Li:Al (100 nm). This might have been correlated with the balance in and magnitude of the mobility of the charge carriers, that is, positive holes and electrons, and also the electronic structure, that is, highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels, of the polymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 307–317, 2006     

Novel method for preparation of quaternary ammonium ionomer from epoxidized styrene–butadiene–styrene triblock copolymer and its use as compatibilizer for blending of styrene–butadiene–styrene and chlorosulfonated polyethylene

A novel method for the preparation of a quaternary ammonium ionomer of styrene–butadiene–styrene triblock copolymer (SBS) was developed by a ring‐opening reaction of epoxidized SBS with triethylamine hydrochloride in the presence of a phase transfer catalyst. The optimum conditions were studied. The ionomer was characterized by quantitative analysis, IR spectroscopy, and ¹H‐NMR spectroscopy. Its water absorbency, oil absorbency, dilute solution viscosity, and use as a compatibilizer for the blending of SBS and chlorosulfonated polyethylene (CSPE) were investigated. The results showed that, under optimum conditions, the epoxy groups can be completely converted to the quaternary ammonium groups. The IR spectrum did not exhibit the absorption peak for quaternary ammonium groups, whereas the ¹H‐NMR spectrum and titration method demonstrated it. With increasing ionic group content, the water absorbency of the ionomer increased whereas its oil absorbency decreased. These indicated the amphiphilic character of the SBS ionomer. The dilute solution viscosity of the ionomer in toluene/methanol (9/1) solvent increased with increasing quaternary ammonium group content. The ionomer was used as a compatibilizer for the blends of SBS and CSPE. The addition of a small amount of the ionomer to the blend enhanced the mechanical properties of the blends: 2 wt % ionomer based on the blend increased the tensile strength and ultimate elongation of the blend nearly 2 times. The blends of equal parts SBS and CSPE behaved as oil‐resistant thermoplastic elastomers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1975–1980, 2006     

Methods to determine solubility parameters of polymers at high temperature using inverse gas chromatography

Experimental values of Flory–Huggins parameters, χ, between polymers and probes, are frequently used to determine the solubility parameters of the polymers by the method of DiPaola–Baranyi and Guillet. The solubility parameters of probes were usually estimated by using heat of vaporization. When χ is measured at a temperature near the critical temperature of the probes and used to determine the solubility parameter of polymers, the departure of enthalpy of the probe vapor from the ideal gas state should be considered. This study discussed the method to make the correction and its effect on the determination solubility parameter of polymers. Without correction in the vapor phase enthalpy, the solubility parameters of the probes and polymer tend to be underestimated and the error increases when the critical temperature is approaching. Analytical expressions for the effect of correction on the solubility parameter of probes and parameters of polymers were derived. By use of probes with a range of solubility parameters on both sides of the solubility parameter of polymers, the correlation between parameters of polymers was shown to be reduced. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1547–1555, 2004     

Exothermic effect in the process of electron‐beam curing of epoxy resins

Temperature measurements have been performed in the process of electron‐beam curing of EB‐I and EB‐II epoxy resin systems. The influence of initiator content, resin type, and dose rate on the temperature of the systems was studied. Transverse and longitudinal temperatures of samples in the glass vessel were also analyzed. The nature of temperature curves varied with the different epoxy resin systems in the steel mold, but did not change with different contents of the initiator. At the same time, the heat had no effect on the gel fraction of epoxy resin systems. The temperature curve was greatly affected by the dose rate, and its peak value, peak width, and plateau value also increased with it. The transverse temperature of EB‐II glass vessel samples increased as the radiation dose increased and, in the same sample, the temperature reduced as the distance between the radiation center and the test point increased. The longitudinal temperature of EB‐I and EB‐II resin systems in a glass vessel decreased as the radiation depth increased. As the radiation dose increased, the temperature of the EB‐I resin system increased simultaneously, while that of the EB‐II resin system initially increased and then kept constant when the dose reached a certain value. The temperatures of these two resin systems decreased rapidly when the radiation process stopped. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2217–2222, 2004     

新型铝酸酯光稳定剂的研究

合成了五种新型铝酸酯光稳定剂并对其紫外吸收性能、荧光性能和热稳定性能进行了表征，探讨了光稳定剂结构、相对分子质量与其性能的关系，并验证它们的光稳定性及其在PE—LD中的光氧化稳定作用。还与紫外线吸收剂BAD和Tinuvin327进行了应用比较。     

Oxygen enrichment from air through multilayer thin low‐density polyethylene films

Several multilayer thin low‐density polyethylene (LDPE) films were fabricated by blown thin film having a thickness of 7 μm and an area of 130 cm². They were characterized for their oxygen‐enrichment performance from air by a constant pressure–variable volume method in a round permeate cell with an effective area of 73.9 cm². The relationship between oxygen‐enrichment properties, including oxygen‐enriched air (OEA) flux, oxygen concentration, permeability coefficients of OEA, oxygen, nitrogen, as well as separation factor through the multilayer LDPE films, and operating parameters, including transfilm pressure difference, retentate/permeate flux ratio, temperature, as well as layer number, are all discussed in detail. It is found that all of the preceding oxygen‐enrichment parameters increase continuously with an increase of transfilm pressure difference from 0.1 to 0.65 MPa, especially for the trilayer and tetralayer LDPE films. The oxygen concentration and separation factor appear to rapidly increase within the retentate/permeate flux ratio below 200, and then become unchangeable beyond that, whereas the OEA flux and the permeability coefficients of OEA, oxygen, and nitrogen seem to remain nearly constant within the whole retentate/permeate flux ratio investigated, especially for the monolayer and bilayer LDPE films. The selectivity becomes inferior, whereas the permeability becomes superior, as the operating temperature increases from 23 to 31°C. The highest oxygen concentration was found to be 44.8% for monolayer LDPE film in a single step with air containing oxygen of 20.9% as a feed gas and operating pressure of 0.5 MPa at a retentate/permeate flux ratio of 340 and 23°C. The results demonstrate a possibility to prepare an oxygen‐enriching membrane directly from air, based on the easily obtained thin LDPE films. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 3013–3021, 2002; DOI 10.1002/app.2331     

Mathematical model for the pultrusion of blocked PU–UP matrix composites

The thermokinetic behavior of blocked polyurethane (PU)–unsaturated polyester (UP)–based composites during the pultrusion of glass‐fiber‐reinforced composites was investigated utilizing a mathematical model that accounted for the heat transfer and heat generation during curing. The equations of continuity and energy balance, coupled with a kinetic expression for the curing system, were solved using a finite difference method to calculate the temperature profiles and conversion profiles in the thickness direction in a rectangular pultrusion die. A kinetic model, dP/dt = A exp(?E/RT)P^m(1 ? P)ⁿ, was proposed to describe the curing behavior of a blocked PU–UP resin. Kinetic parameters for the model were obtained from dynamic differential scanning calorimetry scans using a multiple regression technique, which was able to predict the effects of processing parameters on the pultrusion. The effects of processing parameters including pulling speed, die wall temperature, and die thickness on the performance of the pultrusion also were evaluated. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1996–2002, 2003     

不同玻璃料对PTC陶瓷性能的影响

研究了AST和ASL两种玻璃料对PTC陶瓷性能的影响,发现在1280℃～1340℃的烧成范围内,添加ASL的样品其室温电阻要比添加AST的样品大,而其电阻—温度特性要比添加AST的样品好,且两种样品的晶粒尺寸及晶粒均匀度有明显差别.研究结果表明,两种样品性能上的差异与它们显微结构上的差异有着密切关系.