GH2027铁基高温合金的第二相研究

运用电子显微分析和波谱分析等方法对ＧＨ２０２７合金的第二相进行了研究，结果表明，合金晶界相主要是片状Ｍ６Ｃ和薄膜状Ｍ２３Ｃ６，经波纹图样测得其错配度约为３％，晶内Ｍ６Ｃ和Ｍ２３     

Multiple respiratory gas monitoring causes changes of inspired oxygen concentration in closed anesthesia system

This case report describes an accessory hepatic duct (AHD) identified by intraoperative cholangiography during excisional surgery of a choledochal cyst (CC). The accessory duct was divided and reconstructed successfully to the Roux-en-Y jejunal loop. The postoperative course was uneventful, and follow-up abdominal sonography revealed neither evidence of biliary tract obstruction nor atrophic changes of the liver. It is advocated that an AHD should be meticulously reconstructed if it is divided during excisional surgery of a CC.     

连续重整装置仿真系统的设计开发

为提高操作人员对连续重整装置开停工及事故处理的熟练程度，并对生产进行指导，采用半机理模型结合设计和现场数据介发的连续重整装置仿真系统已在现场成功投用。介绍了该仿真系统的软硬件结构、动态模型及仿真功能。     

Solaris2.X操作系统上NFS的环境配置

本文描述了Ｓｏｌａｒｉｓ２．Ｘ操作系统上网络文件系统ＮＦＳ的特性及其环境配置，介绍了如何建立了ＮＦＳ服务器和ＮＦＳ客户机，从而实现了远程文件系统资源共享。     

语音识别算法的确定与实现

在语音识别的实验中，对几种算法方案进行了比较、分析和择优淘劣，标准是在一定词汇量的条件下，权衡占用机器的内存空间、（正确）识别率和响应速度。力争使与话者有关的单词语音识别系统的设计达到优化，取得满意的结果。本文即是此项实验的总结。     

Growth and characterization of hot-wall epitaxial CdTe on (111) HgCdTe and CdZnTe substrates

Thin CdTe films were deposited by hot-wall epitaxy (HWE) on (111) HgCdTe and CdZnTe substrates at temperatures from about 140 to 335°C. X-ray rocking curves were used to show that crystal quality of the CdTe (111)B films improved as substrate temperature increased from 140 to about 250°C. Rocking curve values for full width at half maximum (FWHM) decreased from 2–4 degrees at 140–150°C to less than 100 arc-s at 250°C, and a FWHM of 59 arc-s was the lowest value observed near 250°C. The FWHM of the HWE CdTe was found to be insensitive to growth rate below about 400Å/min, but increased to four degrees at 1250Å/min. X-ray diffraction confirmed that films grown on the B-face at higher temperatures were epitaxial, but contained a significant volume fraction, 35% to 50%, of rotational in-plane twins. Electron microscopy confirmed a coarse twin density, and photoluminescence spectra showed an absence of excitonic emission in the HWE films. Simultaneous growth on two (111) HgCdTe substrates with different surface polarities between 230°C and 335°C showed that deposition rate on the A-face decreased relative to that on the B-face as temperature increased. Films grown on the B-face exhibited better surface morphologies than those grown on the A-face.     

哈尔滨炼油厂MTBE装置试生产

介绍了哈尔滨炼油厂ＭＴＢＥ装置的工艺路线、新技术的应用及特点；催化剂的装填及应用情况；总结了生产过程中遇到的一系列问题及解决办法；探索了平稳生产的新徐径，以保证装置安全、平稳、长周期运行；同时对反应器操作温度、催化蒸馏塔操作压力、原料中醇烯比等因素对异丁烯转化率及ＭＴＢＥ产品的影响做了简单的总结。     

Abrasive wear of dental composite resins

Abrasive wear is a major problem in the application of dental composite resins. In this study the friction and wear behaviours of two types of dental composites: one containing relatively coarse filler particles and some microfillers (Estilux) and another containing only microfiller particles (Durafill), have been investigated by using a scratch testing machine. Experimental results show that the coefficients of friction in both composites are essentially constant for applied loads up to 20 N. The wear resistance of Durafill is better than Estilux. Under the same testing conditions, the size, shape and distribution of the filler particles are more important variables than applied load and sliding speed in controlling the wear mechanism. It is shown that for Estilux, plastic ploughing by the diamond indenter is the predominant mechanism. For Durafill, however, the formation and propagation of tensile cracks on the worn surface is the main wear mechanism. The effects of two different indenters, diamond and enamel, on the basic wear mechanisms are also discussed.